Rane MS 1 Handleiding
Rane
Niet gecategoriseerd
MS 1
Bekijk gratis de handleiding van Rane MS 1 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 5.0 sterren uit 1.5 reviews. Heb je een vraag over Rane MS 1 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/2
Data Sheet-1
MS 1
MICROPHONE STAGE
Parameter Specification Limit Units Conditions/Comments
Input Impedance 1k 1% W Balanced 500 + 500
Gain Range +21.5 to +60 1.5 dB
Phantom Power +48 4% VDC DIN 45596 & IEC 268-15
Max Input Level 0/-38 1 dBu 21.5/60 dB gain
Equivalent Input Noise -130/-117 2 dBu 20k BW, 60/21.5 dB gain, Rs=150 ohms
Signal-To-Noise Ratio 102/75 (re +4 dBu) typ dB 20k BW, 21.5/60dB gain
Frequency Response 20-20 kHz 0.1 dB -3 dB @ 130/90 kHz, 21.5/60 dB gain
THD+Noise 0.007/.03 .001 % +20 dBu, 20-20 kHz, 21.5/60 dB gain
IM Distortion (SMPTE) 0.008 .002 % 60 Hz/7 kHz, 4:1, +20 dBu
Slew Rate 6 1 V/µs Fully symmetrical
Max Output Level +20 1 dBu Balanced out, 600 ohms
Output Impedance 50 1% W Balanced
Output Cable Length 1000' (305 m) typ Belden 8451 or equivalent
Unit: Agency Listing
..........120 VAC model Class 2 Equipment National Electrical Code
UL & CSA Exempt Class 2 equipment
..........230 VAC model CE-EMC EMC directive 89/336/EEC
CE-Safety Exempt per Art. 1, LVD 73/23/EEC
Power Supply: Agency Listing Class 2 Equipment
..........120 VAC model UL File no. E88261
CSA File no. LR58948
..........230 VAC model CE-EMC EMC directive 89/336/EEC
CE-Safety LV directive 73/23/EEC
..........100 VAC model Built to JIS Japan only
Power Supply Input 18 VAC w/center tap 10% Vrms Rane RS 1 supplied with MS 1
Max Current Consumption 220 mA
Unit Size 1.65" H x 5.1" W x 4.25" D (4.2 cm x 13 cm x 10.8 cm)
..........Weight 1 lb (0.45 kg)
Shipping Size 3.6" H x 11.75" W x 7.2" D (9.5 cm x 30 cm x 18 cm)
..........Weight 4 lb (1.8 kg)
General Description
The Rane MS 1 Mic Stage preamplifier provides the
answer when you need just one microphone input in an
otherwise line-level world. Give us a call to go from either a
dynamic, condenser or electret microphone to a line level
input with a minimum of noise, distortion, cost and hassle.
The MS 1 provides 48 V switchable Phantom Power with
indicator LED, continuous rotary Gain trim between 21.5 dB
and 60 dB, overload LED, and XLR balanced Input & Output
connectors. A Phase Invert switch and high-current cross-
coupled output line drivers round out the features.
The MS 1 utilizes one of the finest ultra low noise
amplifier designs available. Featuring a true differential input
with high common-mode rejection, use of the MS 1 guaran-
tees performance usually found only in mixing consoles
costing thousands of times as much. Of course, for all of that
extra money you receive a proportional increase in KPSI
(knobs per square inch).
Features
• Gain Control with Overload Indicator
• Phase Invert Switch
• Switchable 48V Phantom Power
• Ultra Low Noise Design
DATA SHEET
• True Differential Input
• Cross-Coupled Line Driver
• UL/CSA/CE and 100/120/230 VAC Remote Power Supply
Data Sheet-2
All features & specifications subject to change without notice DOC 103169 PN 08037 2-98
MS 1
MICROPHONE STAGE
Application Information
Uses and applications for the MS 1 should be obvious. But
then again, its obvious to us our taxes are too high and
nothing is being done about that. With this in mind, perhaps a
few words on using the MS 1 might not be wasted.
BALANCED USE
The MS 1 provides a true cross-coupled balanced Output.
This is equivalent to an electronic simulation of a transformer
output. Rane follows the AES standard of pin 2 = hot.
When running a long cable back to the mixer, run a line
level balanced line rather than a mic level line. The compact
MS 1 can mount closer to the microphone, provide a local
volume control (or not, just pull the knob off), while the
stronger signal minimizes RF and hum irritations.
UNBALANCED USE
Balanced use is recommended to minimize noise. When
you must drive an unbalanced device with the MS 1's bal-
anced Output, connect pin 2 to the “+” or “hot” lead, and tie
pin 3 and ground together at the shield.
MIXING
The MS 1 is designed to fill the need for adding one or
two microphone channels to line level mixers, such as the
Rane SM 26B or SM 82. Many installations using either of
these products invariably wind up with one unused input that
would do the job perfectly if only it could operate at mic
level. In rides the MS 1 to the rescue.
DIGITAL RECORDING AND SAMPLING
Another handy use for the MS 1 is in recording applica-
tions. Many popular products do not have a high enough
quality mic preamp to suit the resolution of the digital
processing electronics! Such irony. Using the ultra low noise
MS 1 to bring the mic inputs up to extremely high quality line
level is an easy and affordable solution for this dilemma. No
garbage in; no garbage out. Clippity-clop; clippity-clop.
Block Diagram
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)355-6000 FAX (425)347-7757 WEB http://www.rane.com
MICROPHONE TYPES
The available gain range of the MS 1 allows the use of
virtually any type of microphone. True 48V phantom power
guarantees the MS 1 works with every microphone made. The
better the mic, the better the MS 1 sounds.
Ah, the sound of the thundering hoofs is deafening.
Architectural Specifications
The microphone preamplifier shall be a single channel
stand-alone unit with remote power supply. The power supply
shall be U.L. listed, C.S.A. certified, and CE certified. The
input and output shall be fitted with XLR connectors. A
polarity inverting switch shall be included. Phantom power
shall be provided in compliance with DIN 45596 & IEC 268-
15 and be controlled by a slide switch with an LED indicator.
A gain control shall be provided with 21.5-60 dB adjustment
range. A power indicator and a system overload indicator
shall be provided. High current cross-coupled active output
line driver shall be standard, as well as input RFI filter
protection.
The unit shall be a Rane MS 1 Microphone Stage.
CHASSIS GROUNDING
Units with outboard power supplies do not ground the
chassis through the line cord. Make sure that these units
are grounded either to another chassis which is earth
grounded, or directly to the grounding screw on an AC
outlet cover by means of a wire connected to a screw on
the chassis with a star washer to guarantee proper contact.
Please refer to RaneNote 110, “Sound System Inter-
connection” (supplied in your manual and available on
request separately) for further information on system
grounding.
Product specificaties
| Merk: | Rane |
| Categorie: | Niet gecategoriseerd |
| Model: | MS 1 |
Heb je hulp nodig?
Als je hulp nodig hebt met Rane MS 1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Rane
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
19 Juni 2025
18 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
Handleiding Niet gecategoriseerd
- RME
- Choice
- Teradek
- Nivona
- Teia
- Master Lock
- Seville Classics
- Fannova
- MBZ
- Robus
- LG
- Aeris
- Thetford
- Adastra
- Storm Audio
Nieuwste handleidingen voor Niet gecategoriseerd
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025
30 Juni 2025