Radial Engineering Pro-ISO Handleiding

Bekijk gratis de handleiding van Radial Engineering Pro-ISO (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 49 mensen en kreeg gemiddeld 4.7 sterren uit 5 reviews. Heb je een vraag over Radial Engineering Pro-ISO of wil je andere gebruikers van dit product iets vragen? Stel een vraag

SPECIFICATIONS

ProISO J•ISO

Freq. response 20Hz to 18kHz +/- 1dB 10Hz to 50kHz +/- 1dB

THD @ 1k 0.01% 0.001%

Stereo Inputs Balanced, low-Z, +4dB line-level, 600-Ohm,

female XLR, pin-2 hot

Outputs Unbalanced, high-Z, -10dB line-level

RCA, ¼”, and 3.5mm TRS

Power None, completely passive

Size 3.25” x 5” x 1.875”

Weight 2 lbs.

INPUT PANEL

2. Ground lift disconnects the

signal ground to eliminate buzz and

hum caused by ground loops.

1. XLR INPUTfor balanced,

low-impednce, +4dB line-level

signals.

3. Secondary Ground Liftused

for instances where two separate

devices are connected to the

outputs.

OUTPUT PANEL

4. Output Level provides signal

attenuation to prevent clipping.

5. 3.5mm TRS output connection

for stereo -10dB consumer audio

devices like the iPOD.

6. RCA Phono left and right stereo

outputs for -10dB consumer audio

electronics.

7. ¼” Phone left and right stereo

outputs for high-impedance audio

electronics like mixers.

CONSTRUCTION

8.Bookend design14 gauge steel

outer shell creates protective zone

around connectors and switches.

9.I-beam enclosureeliminates

stress that could torque the PC

board and cause solder joint

failure.

10. PCB mountedswitches are

high-cycle rated for long life.

11.Jensen Radial (J•ISO) and

(ProISO) transformers offer

outstanding audio performance.

12. Military-grade double-sided

PCB with plated through-holes is

bolted to welded steel standoffs.

13. Full-bottom no-slip padThis

provides electrical isolation and

plenty of "stay-put" friction.

www.radialeng.com

Radial Engineering

1638 Kebet Way, Port Coquitlam BC V3C 5W9

Tel: 604-942-1001 Fax: 604-942-1010

email: [email protected]

J•ISO

Pro-ISO

Users Guide

True to the Music

Radial J•ISO and ProISO users guide V1.0 - Part #: R870 1220 00

Subject to change without notice

RADIAL ENGINEERING 3 YEAR LIMITED WARRANTY

RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free from

defects in material and workmanship and will remedy any such defects free of

charge according to the terms of this warranty. Radial will repair or replace (at

its option) any defective component(s) of this product (excluding finish and wear

and tear on components under normal use) for a period of three (3) years from

the original date of purchase. In the event that a particular product is no longer

available, Radial reserves the right to replace the product with a similar product of

equal or greater value. To make a request or claim under this limited warranty, the

product must be returned prepaid in the original shipping container (or equivalent)

to Radial or to an authorized Radial repair center and you must assume the risk

of loss or damage. A copy of the original invoice showing date of purchase and

the dealer name must accompany any request for work to be performed under

this limited warranty. This limited warranty shall not apply if the product has been

damaged due to abuse, misuse, misapplication, accident or as a result of service

or modification by any other than an authorized Radial repair center.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE

FACE HEREOF AND DESCRIBED ABOVE. NO WARRANTIES WHETHER

EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD

DESCRIBED ABOVE OF THREE YEARS. RADIAL SHALL NOT BE RESPON-

SIBLE OR LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES OR LOSS ARISING FROM THE USE OF THIS PRODUCT. THIS

WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU

LIVE AND WHERE THE PRODUCT WAS PURCHASED.

1 23

+4dB Balanced to -10dB Unbalanced

Stereo Signal Conversion Tool

J•ISO ProISO User GuideRadial Engineering Ltd.J•ISO ProISO User GuideRadial Engineering Ltd.

11 12 13

9 10

87654

Product specificaties