QuickCool QC-PC-C01C Handleiding

QuickCool Niet gecategoriseerd QC-PC-C01C

Lees hieronder de 📖 handleiding in het Nederlandse voor QuickCool QC-PC-C01C (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Quick-Ohm Küpper & Co. GmbH
Components – Heat-Management - Ceramics
www.quick-ohm.com vXIII/07/nk
- 1 -
TEC - Controller QC-PC-C01C
Manual
Temperaturecontroller for Cooling
Technial Data:
Dimensions: 65mm x 50mm x 20mm
Temperature range: -20°C…+50°C
Input voltage: 10V…24V
Max. output voltage: equal to input voltage
Max. output current: 10A
1. Basic information QC-PC-C01C
The QC-PC-C01C was designed as controller for cooling to adjust a TEC (Thermoelectric coller)
at a certain temperature. The controller is operated by low DC voltage and should not be exposed
to main voltage. To set up the controller electrical wiring is required, which request some basic
knowledge of electrical circuits. All wiring must be done without connection to the power supply.
Be aware that same components can be damaged or destroyed be incorrect use. Despite of low
voltage, high currents can occur and serious warming and the danger of fire can appear by using
wrong lead wires. Please read this instruction carefully and consult an electrician by any question.
If you remark any warming during operation, the controller must be switched off immediately.
Scope of delivery:
1 TEC - Controller QC-PC-C01C
1 Temperaturesensor NTC 10K ( =3977K) Ω β
1 Potentiometer 10K Ω
1 Manual
Quick-Ohm Küpper & Co. GmbH
Components – Heat-Management - Ceramics
www.quick-ohm.com vXIII/07/nk
- 2 -
2. Operating principle:
A TEC is able to transfer thermal power from one side of the module to the other by consuming
electrical power. The temperature drops on one side of the element, because of heat consumption
while it rises on the other side. For using this heatpump effect in a technical application, a setup
similar to figure 1 is to be built up.
This is the basic setup for any TEC-Application. The area to be temperature controlled must be
equipped with a temperature sensor. On the opposite side, the removed heat must be dissipated to
the ambient. The size of the heatsink and the quality of the thermal contact to the TEC has the
biggest influence on the performance of the whole system. The gap between the TEC and the
mounted parts (hot/cold side) must be as small as possible and only a very little amount auf
thermal conductive should be used to avoid air inclusions in the contact areas. For further
information such as mechanical loads for a durable setup visit our website www.quick-ohm.com.
Heatsink/ hot
side
Thermal
conductive
(Paste, Foil,
etc.)
TEC
(printing on
upper side)
Temp. controlled
area/ cold side
figure 1:
Temperatur
e
sensor
Quick-Ohm Küpper & Co. GmbH
Components – Heat-Management - Ceramics
www.quick-ohm.com vXIII/07/nk
- 3 -
3. Electrical connection:
For operating the controller a DC power supply is needed. Please be aware that the controller has
no internal voltage or current limits and therefore will output the maximum voltage of the power
supply when the set-temperature is much lower than the actual temperature. Make sure, that the
maximum voltage of the power supply is within the range of the TEC. A series connection of
similar TECs can also be used to reduce the voltage for each TEC. Figure 2 shows the electrical
connection of the whole circuit, the colors follow the lead colors of the controller.
By following these instructions and using TECs from QUICK-OHM, the top side of the TEC will
get cold when the right wire showing in the direction of the viewer is red. Applied on the figure
above, the top side would be the warm side.
4. Temperature setting:
The controller has a working range from -20°C to + 50°C. Please notice, that the controller can
only be operated in cooling mode. 50°C can only be reached, when the hot side is above this
temperature. It could be useful to make marks on the potentiometer while the first use. By
adjusting some positions between the left and right stop of the potentiometer and while measuring
the temperature at that steps a small scale can be marked on the potentiometer.
It is possible to integrate a Display (QC-PC-D-100) in the setup. This device shows the set-
temperature as well as the actual temperature.
Controller
QC-PC-C01C
+ -
Power supply
10V … 24V
TEC
Temperatur-
Sensor
NTC 10K Ω
Potentiometer 10K
Ω
figure 2:
White
+5V Poti
Yellow
Control
Poti-Signal
Green
Gnd
Sens/Poti
Grey
Sensor
Signal
Red
+PE
Blue
-PE
Black
GND
Orange
10..24V

Product specificaties

Merk: QuickCool
Categorie: Niet gecategoriseerd
Model: QC-PC-C01C

Heb je hulp nodig?

Als je hulp nodig hebt met QuickCool QC-PC-C01C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd QuickCool

QuickCool

QuickCool QC-PC-C01C Handleiding

28 Februari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024