QSC SC-2150 Handleiding

QSC Speaker SC-2150

Lees hieronder de 📖 handleiding in het Nederlandse voor QSC SC-2150 (7 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7
TD-001624-01-A
*TD-001624-01*
SC-2150
Quick Start Guide
SC-2150 Screen Channel Loudspeaker System
®
2
TD-001624-01-A
EXPLANATION OF SYMBOLS
The term
“WARNING!”
indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death.
The term
“CAUTION!”
indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result
in damage to the equipment that may not be covered under the warranty.
The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.
The term
"NOTE"
is used to indicate additional useful information.
The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important safety, and
operating and maintenance instructions in this manual.
IMPORTANT SAFETY INSTRUCTIONS_____
Refer to TD-000142 Safety Precautions contained in the shipping carton.
Warranty
For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com
Introduction
The SC-2150 is a 3-way, selectable passive full-range or bi-amplified screen channel loudspeaker system comprised of two main units. These
units are shipped in separate cartons.
DCS-2150-HF Mid-High Frequency Loudspeaker System
Part Quantity
DCS-2150-HF Loudspeaker System 1
Wiring Harness *
TD-000142 Safety Precautions 1
TD-000453 Warranty 1
* Part of the HF Loudspeaker System
DCS-2150-LF Low-Frequency Enclosure
Part Quantity
DCS-2150-LF Loudspeaker Enclosure 1
Hex-head Screw 3
Flat Washer 3
Split Washer 3
TD-000142 Safety Precautions 1
TD-000453 Warranty 1
— Figure 1 —
DCS-2150-HF
DCS-2150-LF
3
TD-001624-01-A
Assemble the SC-2150
This procedure assumes that both items and associated hardware is unpacked and the two
units are placed on a solid flat surface near the installation location.
Refer to — Figure 2
1. Place the HF horn assembly (1) on top of the LF enclosure (2) with the three holes in
the pan-and-tilt bracket (not visible in the illustration), aligned with the three holes (3)
in the top of the LF enclosure.
2. Assemble the three bolts (4a), split washers (4b), and flat washers (4c) and install
through the pan-and-tilt bracket into the LF enclosure.
3. Tighten the bolts. Be careful not to over tighten.
Refer to — Figure 3
4. Connect the Neutrik SpeakON NL4 plug (1) (end of the wiring harness coming from the
HF System) to the LF Enclosure connector plate NL4 receptacle (2).
NOTE:The NL4 is a keyed plug/receptacle that can only go in one way.
5. After engaging the plug all the way, twist the plug clockwise until it locks.
6. Use the Mode switch (3) to select Bi Amp or Passive.
Passive Mode
– (— Figure 4) a single amplifier channel drives the entire system. The
Mode Switch (3) must be in the PASSIVE position and only the right-side pair of terminals
are used to connect the amplifier to the loudspeaker system.
Bi-Amp Mode
– (— Figure 5) two amplifier channels are required. One for the LF
enclosure and one for the Mid-Hi system.
CAUTION!
An active crossover must be used to protect the loudspeaker from
damage. It is highly recommended to use a QSC processor with factory DSP
presets for the SC-2150 for best results.
The Mode Switch must be in the BI-AMP position and all four terminals are used to connect the amplifier to the loudspeaker. The Low
Frequency amplifier connects to the left pair of terminals and the High Frequency amplifier connects to the right pair of terminals.
CAUTION!
In all cases, be sure to observe proper polarity when making connections. The “+” terminal of the amplifier
should connect to the “+” terminal of the loudspeaker.
In Bi-Amp mode, be sure that LF and HF connections are not reversed. HF drivers can be damaged if they are connected
to the low frequency amplifier.
— Figure 2 —
1
2
3
4
4a
4b
4c
DCS-2150-HF
DCS-2150-LF
— Figure 3 —
To Mid-High System
1
2
3
®
— Figure 4 —
To amplier channel
— Figure 5 —
To amplier channel two (HF)
To amplier channel one (LF)

Product specificaties

Merk: QSC
Categorie: Speaker
Model: SC-2150

Heb je hulp nodig?

Als je hulp nodig hebt met QSC SC-2150 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker QSC

QSC

QSC SC-1120 Handleiding

20 Juni 2023
QSC

QSC AD-S282H Handleiding

20 Juni 2023
QSC

QSC GP218-sw Handleiding

18 Juni 2023
QSC

QSC SR-5152 Handleiding

14 Juni 2023
QSC

QSC AD-P6T Handleiding

12 Juni 2023
QSC

QSC AD-DWL.180 Handleiding

11 Juni 2023
QSC

QSC AD-DWL.SUB Handleiding

5 Juni 2023
QSC

QSC KLA181 Handleiding

5 Juni 2023
QSC

QSC SR-1290 Handleiding

24 Mei 2023
QSC

QSC WL2082-i Handleiding

20 Mei 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

OTTO

OTTO Bluetooth Revo NC2 Handleiding

20 April 2024
REL Acoustics

REL Acoustics Strata Handleiding

20 April 2024
REL Acoustics

REL Acoustics Strata III Handleiding

20 April 2024
Soen

Soen Transit Handleiding

18 April 2024
Miller & Kreisel

Miller & Kreisel MP300RC Handleiding

18 April 2024
Soen

Soen Transit XS Handleiding

18 April 2024
Miller & Kreisel

Miller & Kreisel MP7 Handleiding

18 April 2024
Qian

Qian QRBT1801 Handleiding

17 April 2024
Focal

Focal Twin6 Handleiding

17 April 2024
Kenwood

Kenwood KFC-WPS1000F Handleiding

16 April 2024