Pyle PLMRC500X1 Handleiding

Pyle Receiver PLMRC500X1

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PLMRC500X1 (12 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
Mono-Block Weather Resistant Audio Amplifier System
PLMRC500X1
Class D Compact Designed Suit for Car, ATV,
UTV, 4X4, Jeep, Motorcycle and Marine,
and any other Weather Resistant Application
www.PyleUSA.com
2
INTRODUCTION
This power amplier has been designed to provide high quality performance
with a minimum of maintenance. However, it's performance will only be as good
as the care and quality of components with which is installed.
We therefore advise that you read these instructions very carefully to familiarize
yourself with the product and it's features.
Before installing the power amplier please read this instruction manual
carefully. The instructions for mounting and connecting the set have to be
followed precisely. If necessary, a service center should be consulted.
All connections for DC power, signal input and speaker outputs can be carried
out easily and safely byway of RCA and screwed terminals.
INSTALLATION INSTRUCTIONS
Please choose a mounting place without any direct weather inuences.
Note that the amplier generates heat so that a well ventilated place is necessary.
According to your car's construction the set can be made very carefully in order
to ensure the amplier's full performance and reliability.
Keep the wire connections as short as possible with sucient dimensions in
order to minimize power losses and provide a higher audio output of the system.
For safety reasons route all power and speaker wiring by using the exiting wire
channels. To minimize damage to the cables, take care that they do not pass
sharp edged metal. Lay all cables as far away as possible from the ignition cables,
modules in the boot and under the key dashboard, as this create interference.
Add a fuse into the (+) power cable in a distance of not more than 30 cm from
the positive battery pole.
Keep the length of the power wires as short as possible. It is better to use power
cables which are short and then longer speaker cables.
In order to reduce interference, also pay attention to the instructions.
www.PyleUSA.com 3
PRECAUTIONS
This unit is designed for negative ground 12-14.50 VoIts (DC) operation only
Use speakers with an impedance of 1 to 4 Ohms (2 to 8 Ohm when used as
bridged two amplier)
Avoid installing the unit where:
It would be subject to high temperatures, such as from direct sunlight or hot
air from the heater.
It would be exposed to rain or moisture.
It would be subject to dust or dirt.
If your car is parked in direct sunlight and there is a considerable rise in
temperature inside the car, allow the unit to cool o before operation.
When installing the unit horizontally, be sure not to cover the heatsink ns
with the oor carpet.
If this unit is placed too close to the car radio, an interference may occur in this
case, separate the amplier from the car radio.
This power amplier employs a protection circuit to protect the transistors and
speakers if the amplier malfunctions.
Do not attempt to test the protection circuits by covering the heatsink or
connecting improper loads.
Do not use the unit with a weak auto battery as its optimum performance
depends on a normal battery supply voltage.
For safety reasons, keep the volume of your car audio system moderate so that
you can still hear normal trac sounds outside your car.
FUSE REPLACEMENT
If the fuse blows, check the power connection and replace the fuse. If the fuse
blows again after replacement, there may be an internal malfunction.
In this case, consult your dealer.
WARNING: Use the specied amperage fuse. Use of a higher amperage fuse
may cause serious damage.
PROTECTION CIRCUIT
This amplier is provided with a protection circuit which operates in the
following cases when:
the unit is overheated.
the speaker terminals are short circuited.


Product specificaties

Merk: Pyle
Categorie: Receiver
Model: PLMRC500X1

Heb je hulp nodig?

Als je hulp nodig hebt met Pyle PLMRC500X1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Pyle

Pyle

Pyle PLAM2001D Handleiding

24 Februari 2024
Pyle

Pyle PT1100 Handleiding

24 Februari 2024
Pyle

Pyle PFA100 Handleiding

24 Februari 2024
Pyle

Pyle PDA35BT Handleiding

24 Februari 2024
Pyle

Pyle PHDA6BT Handleiding

18 December 2023
Pyle

Pyle PDA77BU Handleiding

18 December 2023
Pyle

Pyle PT865BT Handleiding

13 December 2023

Handleiding Receiver

Nieuwste handleidingen voor Receiver