Pyle PLBX8A Handleiding

Pyle Subwoofer PLBX8A

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PLBX8A (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
PLBX8A
8” 600 Watts Low-Profile Active Amplified
Car Audio Subwoofer System
Suitable for Under-seat Installations
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
www PyleUSA com
2www PyleUSA com 3
Introduction
With the , we are introducing a low-prole amplied subwoofer. Low enough to PLBX8A
easily t below the seat of your car. This system oers you a quick and easy way to add a
high-powered subwoofer system to your audio system.
The integrated amplier in the features low pass crossovers, and a control forPLBX8A
adjusting the input sensitivity from 0.12V to 3.5V.
Both high level (speaker level) and low level (RCA type) inputs are present, making this a
universal solution for use with any head unit or other input source.
For further exibility in the use of a subwoofer, a variable bass boost control has been
included. You can control the subwoofer level with the remote level control module.
Mounting the Subwoofer
1. Find a suitable location in the vehicle in which to mount the amplier.
A typical location is shown below:
2. Make sure there is sucient air circulation around the intended mounting location.
3. Mark the location for mounting hole screws by positioning the cabinet where you wish to
install it. Make a small mark to identify the position and remove the unit. Thoroughly clean
the area you plan to attach the subwoofer, using a vacuum cleaner and press down on it
securely.
Control Panel and Features
1. POWER ON LED INDICATOR
2. PROTECT LED INDICATOR
3. PHASE SHIFT: Use this switch to help compensate for time alignment problems in the
system. Such problems usually result from having the subwoofer at a dierent distance
from the listener than the other speakers in the system.
4. AUTO POWER ON: During ON mode, It’s not necessary to connect the remote cable if
you’re using the high level inputs. Do not function with the RCA inputs. On the contrary
while it is during AUTO POWER OFF mode that it needs remote cable connection to turn
on the unit.
5. LOW PASS FILTER: This control permits you dene the ferquency range you want the
subwoofer amplier to receive. The subwoofer will reproduce all sound BELOW the
frequency you set. If the rest of your system is weak on the mids, you may wish to set this
control relatively high. If the midrange is well covered by the rest of your system, you will
probably want the subwoofer to only receive lower frequency signal.
6. BASS BOOST: The bass boost feature will increase the sound level the bass frequencies.
7. INPUT GAIN CONTROL: After you have installed your system, turn this control to minimum.
Turn the head unit on (and the subwoofer will turn on via the remote connection).
Turn the head unit volume to about 2/3 full level. Slowly turn up the subwoofer input
gain control until you hear a small amount of distortion. Then reduce the level until the
distortion is completely gone. Leave the control at this setting.
8. REMOTE LEVEL CONTROL PORT: Attach the included remote level control to cotrol the
volume level of the subwoofer independently.
9. HIGH LEVEL (speaker level) INPUTS: If your head unit does not have RCA outputs, you
can use the speaker outputs for the audio source for the . Use the supplied PLMRSBA8
cable and connect the outputs properly as shown in the connection diagram in this manual.
10. LOW LEVEL RCA INPUTS: Low level inputs are the recommended way to introduce the
audio signal to the subwoofer if RCA outputs are present on your head unit or other
signal source (such as a sound processor).
11. The fuse is rated at 25A. Do not use a fuse with a dierent value and FUSE: NEVER
replace the fuse with a wire or coin.
12. POWER TERMINALS
www PyleUSA com
4www PyleUSA com 5
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance.
Most trunk or hatchback installations will require a 15-20 foot RCA cable, while pickup trunks
and under-seat installations will require a 6-12 foot RCA cable. Always use a high quality
cable.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplier at the same time!
High Level Input Wiring
The high level input(s) should only be used when your receiver lacks RCA outputs.
If the RCA outputs are not present, connect the speaker outputs from the receiver to the
high level input connector of the amplier. Be sure to observe polarity to avoid audio phase
problems.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplier at the same time!
Power Connections
Connect the ground terminal to the closest point on the chassis of the vehicle.
Keep this ground wire to less than 39” (100 cm) inlength. Use 8 gauge (or heavier) wire.
AUTO POWER ON During o mode, connect the remote terminal to the remote output of
the head unit using 16 gauge (or heavier) wire. Connect an empty fuse holder within 18” (45
cm) of the car battery, and run 8 gauge (or heavier) cable from this fuse to the amplier
location. Then connect the fuse holder to the “ ” connection on the subwoofer rear BATT+
panel.
Remote Level Control Connection
Instal the remote control securely under the
dash or in a similar location where using it will
not distract the driver.
To REMOTE TURN-ON
terminal of head unit

Product specificaties

Merk: Pyle
Categorie: Subwoofer
Model: PLBX8A

Heb je hulp nodig?

Als je hulp nodig hebt met Pyle PLBX8A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Subwoofer Pyle

Pyle

Pyle PLR38I Handleiding

24 Februari 2024
Pyle

Pyle PLRG23C Handleiding

24 Februari 2024
Pyle

Pyle PLND35 Handleiding

24 Februari 2024
Pyle

Pyle PLMG85 Handleiding

12 Juni 2023
Pyle

Pyle PLML50FB Handleiding

5 Juni 2023
Pyle

Pyle PLBS122 Handleiding

4 Juni 2023
Pyle

Pyle PPA12 Handleiding

3 Juni 2023
Pyle

Pyle PLML51DB Handleiding

31 Mei 2023
Pyle

Pyle PLMRM4BTA Handleiding

26 Mei 2023
Pyle

Pyle PSABASS12 Handleiding

22 Mei 2023

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

RCF

RCF S 19 Handleiding

10 April 2024
RCF

RCF S 29 Handleiding

10 April 2024
KEF

KEF KC92 Handleiding

6 April 2024
Klipsch

Klipsch Reference Premiere RP-1200SW Handleiding

3 April 2024
Klipsch

Klipsch Reference Premiere RP-1000SW Handleiding

3 April 2024
Velodyne

Velodyne Deep Waves 10 Handleiding

27 Maart 2024
Klipsch

Klipsch PRO-1000SW Handleiding

27 Maart 2024
Totem

Totem KIN Sub Handleiding

27 Maart 2024
Velodyne

Velodyne Deep Waves 12 Handleiding

27 Maart 2024
Kanto

Kanto SUB8V Handleiding

27 Maart 2024