Pure Acoustics HT 770 Handleiding

Pure Acoustics Speaker HT 770

Bekijk gratis de handleiding van Pure Acoustics HT 770 (5 pagina’s), behorend tot de categorie Speaker. Deze gids werd als nuttig beoordeeld door 39 mensen en kreeg gemiddeld 4.4 sterren uit 20 reviews. Heb je een vraag over Pure Acoustics HT 770 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/5

IMPORTANT SAFETY NOTE:PROPER SELECTION OF MOUNTING

HARDWARE NOT INCLUDED HEREIN AND PROPER ASSEMBLY AND

INSTALLATION OF BRACKETS,INCLUDING BUT NOT LIMITED TO

SELECTION OF APPROPRIATE WEIGHT BEARING SUPPORT AND

BRACKET USE WITH THE SPECIFIED SPEAKER ONLY IS THE EXCLUSIVE

RESPONSIBILITY OF THE CUSTOMER MANUFACTURER DISCLAIMS ANY

LIABILITY FOR THE SELECTION OF MOUNTING HARDWARE AND OR

BRACKET INSTALLATION.

Bracket assembly and mounting:

Bracket

Bracket assembly

assembly

assembly and

and

and mounting:

mounting:

Loosen and remove the molded nut (2) by tuming it counter clockwise.Use

the supplied metal bar (5) if necessary by inserting it in one of the holes on

the molded nut (2).

Pull the ball/shaft (3) out of the wall bracket (4).b.

Slide on the molded nut (2) onto the ball/shaft (3) with threaded opening

facing the ball,and thread on the metal nut (1) all the way onto the ball/shaft

(3),with the nut (1)’s knuned surface facing away from the ball.” ”

Screw on the ball/shaft (3) into the threaded insert on the back of the speaker

cabinet (6) until it is fully seated aganst the bottom of the insert.

Tighten the knurted nut (1) using a crescent wrench until it is firmly seated

against the back of the speaker and has fully locked the ball/shaft (3) and the

speaker cabinet together.Please note that once this nut is tightened,it may

embed some marks on the back of the speaker where the attachment is

made.However these marks will be covered by the nut (1).

” ”

Mount the wall bracket (4) onto a wood stud on the wall,using#10,minimum

1 inch long,wood screws.Make sure that all 4 screws are driven into the stud

and not in drywall if the bracket needs to be mounted on drywall,the use of

properly selected and installed wall-anchors and screws is essential.

Holding the speaker cabinet (7) with both hands,reinsert the ball portion of

the ball/shaft (3) into the wall bracket (4).

Hand tighten the molded nut (2) while positioning the speaker for the intended

orientation. Please do NOT tighten the molded nut (2) too hard to avoid

damaging the bracket.

Once the orientation of the speaker is finalized,use the metal bar (5) in one

of the holes on the molded nut (2) and tighten securely . Please do NOT

press hard and strike the speaker when it is finalized.

Product specificaties

Merk:	Pure Acoustics
Categorie:	Speaker
Model:	HT 770
Kleur van het product:	Wit
Breedte:	87 mm
Diepte:	112 mm
Hoogte:	87 mm
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	120 W
Equalizer-instellingen:	Nee
Aanbevolen gebruik:	Luidsprekerset
Impedantie:	8 Ohm
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Muur-montage
Aantal drivers:	1
Woofer:	Nee
Frequentiebereik:	65 - 200000 Hz
Gevoeligheid:	88 dB
Luidspreker soort:	1-weg
Versterker:	Nee
Diameter mid-range driver:	3 "
Tweeter:	Nee