Princeton Tec Switch RGB Handleiding
Princeton Tec
Niet gecategoriseerd
Switch RGB
Bekijk gratis de handleiding van Princeton Tec Switch RGB (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 10 mensen en kreeg gemiddeld 4.6 sterren uit 5.5 reviews. Heb je een vraag over Princeton Tec Switch RGB of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
SWITCH
®
RGB
HELMET LIGHT
Operating and Maintenance Instructions
English
Battery Installation
See Figure 1
(2) CR2016 Coin Cells - 6V
Princeton Tec cares about the environment and recommends recy-
cling batteries. For more information about battery recycling, please
go to: batteryrecycling.com To install the batteries, rotate light unit out
of base. Lift tab of battery door on the underside of light unit to expose
coin cell(s)
Install coin cell(s) batteries with the (+) positive side facing up. Improper
installation of the batteries will damage the light and void the warranty.
Replace the battery door with the lift tab properly aligned with lift tab
slot of the housing. Press door rmly in place making sure it is all the
way seated in place.
WARNING !
Never mix fresh and used batteries.Never mix different battery brands
or chemistry types.
Always remove drained batteries immediately.
Remove batteries during long periods of storage.
Switch Operation
Switch RGB (White mode version). See Figure 2a
Starts in color mode
Press 1x Color Low
Press 2x Color High
Press 3x Off
Press & Hold in color mode White High
Next Press Off
Press & Hold 5s in off Programming mode
Switch RGBIR (IR mode version). See Figure 2b
Starts in IR mode
Press 1x IR Low
Press 2x IR High
Press 3x Off
Press & Hold in IR mode Color High
Next Press Off
Press & Hold 5s in off Programming mode
Programming Mode
See Figure 3
1. The Switch RGB ships with red light selected
2. From off, press and hold for 5 seconds to enter programming
mode
3. When in programming mode, click to activate the desired color
(Red, Blue, or Green)
4. Press and hold for 5 seconds to exit programming mode and
save changes
Troubleshooting
If the Switch RGB fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is conrmed.
• This light has been designed to be water resistant. Check the light for
water contamination on the circuit board. The light will resume normal
operation once any water is shaken or blown out and the light is left
open until completely dry. If the light has been contaminated with salt
water, ush the unit with fresh water and dry as described above.
USA– International 1-Year Warranty
WARRANTY – Princeton Tec warrants this product to be free from de-
fects in workmanship and materials under normal use for one year. This
warranty covers all of the component parts of the product except batter-
ies. This warranty does not cover deterioration due to normal wear or
damage due to misuse, alteration, negligence, accidents, or unautho-
rized repair. Princeton Tec will repair or replace parts which are defective
in workmanship or materials. Your authorized Princeton Tec Dealer and
Princeton Tec are the only facilities authorized to repair the product.
After (3) unsuccessful attempts (within the warranty
period) to repair the product, you have the right to elect replacement of
the product or a refund of the purchase price less allowance for use of
the product. NO INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE
INCLUDED IN THIS WARRANTY. (Some states do not allow the exclu-
sion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.) This warranty gives you
specic legal rights, and you may also have other rights which vary from
state to state.
Princeton Tec reserves the right to change product specications with-
out notice.
FOR CALIFORNIA RESIDENTS
WARNING: This product contains Bisphenol A (BpA) a chemical
known to the State of California to cause birth defects or other re-
productive harm.
Return Policy
If your light fails to operate, follow these simple steps:
1. Check batteries. Replace if necessary.
2. To send your light in for repair or replacement, rst contact Prince-
ton Tec customer service on
1-800-257-9080 to request an RMA number. Please have your
light model, date of purchase and a brief description of the fault
your are experiencing. No warranty repairs will be accepted with-
out an RMA number.
3. Return the light to: Princeton Tec, PO Box 8057 Trenton NJ
08650. Postage due and freight collect items will not be accepted.
4. Upon receipt your light will be processed in about two weeks.
Please allow additional time for return transportation from NJ.
Princeton Tec
PO Box 8057, Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
© 2023 Princeton Tec
Figure 1 – Battery Installation
1 2 3 4
Figure 2 – Switch Operation
Press 1x:
Red Low
Press 2x:
Red High
Press 1x:
O
Press 3x:
O
2s hold from red:
White
Press 1x:
IR Low
Press 2x:
IR High
Press 1x:
O
Press 3x:
O
2s hold from IR:
Color High
IR
IR
2a
2b
Figure 3 – Programming Mode
5s hold from o:
Programming Mode
Press & cycle
to desired color:
5s hold on
desired color:
Save color
Figure 4 – ARC Rail Installation
Slide ARC Rail Adapter into ARC rail to desired position and secure in place with
center anti-slip lock screw.
DO NOT OVERTIGHTEN this screw.
1
2 3
Figure 5 – MOLLE Mount
Slide clip inside any strap position, pinch MOLLE strap to hook the lower end of
the metal clip onto the strap.
1
2
3
Figure 6 – M-LOK
®
Mount
Insert screw and T-nut into M-LOK
®
mount. T-Nut “gap” must be slightly greater
than the thickness of the
mounting surface. Slide mount on to M-LOK
®
rail and tighten with screwdriver.
1
2
SET GAP
3 4
Figure 7 – MICH Mount Installation
Back the screw out so the end of screw is ush with metal U-clip. Slide the
exposed U-clip over the bottom edge of your helmet with the metal clip on the
inside and the plastic base exposed on the outside of your Helmet. Holding Mount
rmly upward, tighten center slotted screw until it stops.
1
2 3
Figure 8 – Picatinny Rail Mount
Remove the center through screw from the side of the Picatinny base mount.
Slide Picatinny to desired position and insert side locking screw aligning with any
slot in Picatinny rail and tighten to clamp in place.
DO NOT OVERTIGHTEN this screw.
1 2 3
Figure 9 – (ABR) Above Rail Mount
A. If using MPLS ABR on a ballistic helmet, skip to step two. For use with
nonballistic helmets, begin by snapping off unneeded portion of ABR mount by
hand or with a pair of pliers, and discarding the smaller ‘hook’ portion
1a 2a
B. Loosen or remove front rail screw, and slide ABR into desired position beneath
rail. Retighten front rail screw.
1b 2b 3b 4b
C. Select Charge MPLS mount and secure with included machine screws, gently
tightening with a Phillips screwdriver. Install Switch/Point onto mount.
1c
1c
2c
2c
3c
3c
English
Product specificaties
| Merk: | Princeton Tec |
| Categorie: | Niet gecategoriseerd |
| Model: | Switch RGB |
Heb je hulp nodig?
Als je hulp nodig hebt met Princeton Tec Switch RGB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Princeton Tec
25 Februari 2025
25 Februari 2025
7 December 2024
17 April 2024
30 Januari 2024
Handleiding Niet gecategoriseerd
- Alecto
- BDI
- Brondell
- Yaesu
- CubuSynth
- Urbanista
- Master Kitchen
- CELLFAST
- Avantone Pro
- Burigotto
- EtherWAN
- Kindermann
- Philos
- Alpha Tools
- Numatic
Nieuwste handleidingen voor Niet gecategoriseerd
14 September 2025
14 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025