PowerWalker VI 600 ST ZA Handleiding

Bekijk gratis de handleiding van PowerWalker VI 600 ST ZA (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.9 sterren uit 6 reviews. Heb je een vraag over PowerWalker VI 600 ST ZA of wil je andere gebruikers van dit product iets vragen? Stel een vraag

User Manual

Line-interactive UPS

PowerWalker VI ST ZA Series

600 / 1200 / 2200

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation

and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION!To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area

free of conductive contaminants. (See the specifications for the acceptable temperature and humidity range.)

CAUTION!

To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid exposing the

unit to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces. The

location should provide adequate air flow around the UPS with 20 CM minimum clearance on front, rear, left and right

sides for proper ventilation

CAUTION! Do not attach non-computer-related items, such as medical equipment, life- support equipment,

microwave ovens, or vacuum cleaners to UPS.

CAUTION! Do not plug the UPS input into its own output.

CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-

containing vessels on or near the unit.

CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power

supply to properly disable the UPS.

CAUTION! Do not attach a power strip or surge suppressor to the UPS.

CAUTION! Internal battery voltage is 12Vdc. Sealed, lead-acid, 6-cell battery.

CAUTION! Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the

required precautions. Keep unauthorized personnel away from batteries.

CAUTION! When replacing the batteries, use the same number and type of batteries.

CAUTION! Do not dispose of batteries in a fire. The battery may explode. Do not open or mutilate the battery or

batteries. Released electrolyte is harmful to the skin and eyes.

UNPACKING

Inspect the UPS upon receipt.

The box should contain the following: (1) UPS x1; (2) User Manual x1; (3) USB Cable x1.

OVERVIEW

The UPS provides automatic voltage regulation for inconsistent utility power, and provides battery backup during

power outages, and ensures consistent power to your computer system.

HARDWARE INSTALLATION GUIDE

1.Your new UPS may be used immediately upon receipt. However, recharging the battery for at least 8 hours is

recommended to ensure that the battery's maximum charge capacity is achieved. Charge loss may occur during

shipping and storage. To recharge the battery, plug the UPS into an AC outlet. The unit will charge in both the on

and off position.

2.With the UPS turned off and unplugged, connect the computer, monitor, and any equipment into the battery power

supplied outlets. DO NOT plug a laser printer, copier, space heater, vacuum, paper shredder or other large

electrical device into the battery power supplied outlets. The power demands of these devices will overload and

possibly damage the unit.

3.Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is protected

by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air conditioner,

refrigerator, copier, etc.) Avoid using extension cords.

4.Depress the power switch to turn the UPS on. The power on indicator light will illuminate and the UPS will "beep".

5.If an overload is detected, an audible alarm will sound and the UPS will emit one long beep. To correct this, turn

the UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Wait 10 seconds.

Make sure the circuit breaker is depressed and then turn the UPS on.

6.To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7.To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery

every three months to ensure battery life.

1200/2200 600 1200 600 2200

6.USB COMM. Port

This port allows connection and communication

from the USB port on the computer to the UPS

unit.

7.Input Circuit Breaker

The circuit breaker provides optimal overload

protection.

8.Input power cord

Connect to utility power.

9.Battery Backup & Surge Protected Outlets

Provide battery backup and surge protection. They

ensure power is provided to connected equipment

over a period of time during a power failure.

1.Power Switch

Press the switch for 2 seconds to turn the UPS ON

or OFF.

2.Led Indicators

This LED is illuminated when the UPS is working.

3.AC Mode LED

The green LED will light when utility power is

normal.

4.Battery Mode LED

The yellow LED will light when input power is

abnormal and the unit will work in battery mode.

5.Fault LED

The red LED will light when fault or over load

occurs.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY INSTRUCTIONS

Product specificaties