POWEREX MH-C940 Handleiding

Bekijk gratis de handleiding van POWEREX MH-C940 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 11 mensen en kreeg gemiddeld 4.3 sterren uit 2 reviews. Heb je een vraag over POWEREX MH-C940 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

PRINTED IN TAIWAN A03-3713510-000

Thank you for purchasing the Powerex MH-C9 Charger-40

Analyzer. Read these instructions carefully before

operating this unit.

GET STARTED VIDEO

Learn how to use the MH-C940 Charger-Analyzer

YouTube Video Link: https://youtu.be/oQFK8UqIxjQ

Or Scan the QR Code with your phone

GENERAL PRECAUTIONS

Do not charge battery cells other than NiMH or NiCD. AA

batteries must be able to accept a 1000mA (Turbo Mode)

/ 500mA (Default Mcharge current. AAA Batteries ode)

must be able to accept a 500mA (Turbo Mode) / 250mA

(Default Mode) charge current.

Do not use the T Mode on AA batteries rated 2 hour urbo

under 2000mAh and AAA batteries under 700mAh. To

charge them, use the Default Mode (refer to “Default

Mode”).

Do not expose the unit to rain or moisture due to the risk

of re.

Do not operate the charger if it appears damaged in any

way.

Always place the battery cells with positive tip facing the

top. Incorrect polarity may cause re or explosion.

Observe polarity diagrams located on the charger.

Do not allow the unit to be exposed to direct sunlight.

Operate in well-ventilated area.

Do not allow the battery terminals to become shorted.

To reduce the risk of damage to the power cord, always

pull by connector rather than the cord.

FEATURES & SPECIFICATIONS

Charges 1-8 AA or AAA NiMH rechargeable batteries

independent ly

2 Charging Speeds: Default Soft Mode and Turbo Mode

Deep Battery Conditioning System to rejuvenate older

batteries with capacity readout

Backlit LCD display with On/O option

Ultra quiet fanless operation with thermal protection

Turbo Charge Current:

1000mA (AA), 500mA (AAA)

Default Charge Current:

500mA (AA), 250mA (AAA)

Microprocessor:

Ninth-Generation MH-

NM7108 Powerex Precision

Microprocessor

Charge Time*:

120 Minutes (Turbo), 240

Minutes (Default)

Input Voltage:

AC 100-240V 50-60Hz

* Charge time based on 2000mAh capacity batteries. Charge

time will vary depending upon the brand, capacity, and

condition of batteries being charged.

MODES

This section explains various charging modes and when to use

them. To enable each mode, refer to the “Operation” section.

Default Mode

Soft charge to maximize battery life and

performance. Recharging time is approximately 4-6

hours.

NOTE: Time may vary depending on battery

capacity and how much charge is remaining in the

battery.

Suitable for most NiMH or NiCD batteries.

Recommended if recharging time is not critical.

Turbo Mode

Faster recharging time. Charges twice as fast as the

Default Mode, approximately 2-3 hours.

Recommended for AA NiMH batteries with capacity

of at least 2000mAh and AAA NiMH with capacity of

at least 700mAh.

Conditioning Mode

Rescues degraded batteries and exercise

infrequently used batteries.

Rejuvenates and cycles the batteries. It applies a

special conditioning cycle which restores battery

performance. Requires up to 48 hours to complete

the cycle.

Actual capacity will be displayed at the end of the

conditioning cycle.

Recommended every 6 months or once a year to

ensure battery performance.

OPERATION

Default Mode

1. Plug the power connector to the charger rst then plug

the AC adapter into the wall outlet.

2. Insert AA and/or AAA batteries. For best performance,

insert the batteries from the left to right.

3. Once the battery is inserted, charging will commence for

that slot. Each slot number will start flashing indicating it’s

charging.

The displayed mAh value represents the amount of

energy that was charged into the battery. It is NOT

the actual capacity of the battery.

4. Charging time will take approximately 4-6 hours.

Once a battery is done charging, the slot number will stop

ashing and remain solid. The charger will display DONE

for each channel that is done charging. The charged

battery may be removed for use.

The displayed mAh value represents the amount of

energy that was charged into the battery. It is NOT

the actual capacity of the battery.

MH-C940

Charger-Analyzer

Product specificaties