Polaroid 8x10 Film Processor Handleiding

Polaroid Fotocamera 8x10 Film Processor

Lees hieronder de 📖 handleiding in het Nederlandse voor Polaroid 8x10 Film Processor (11 pagina's) in de categorie Fotocamera. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/11

8 x 10 Film Processor

User Guide

HOW TO USE THE POLAROID 8 X 10

FILM PROCESSOR, THE FILM HOLDER

MODEL 81-O6, AND THE LOADING

TRAY MODEL 81-09

Introduction

Polaroid 8 x 10 photography provides a self-contained

larger format instant photographic system. You need

no darkroom, no chemical solutions and no time-

consuming processing procedures. The Polaroid 8x10

film holder can be used on most 8 x 10 cameras that

take standard 8 x 10 film holders, on specially adapted

copy cameras and other cameras of extra large format,

and on a variety of technical imaging devices.

The system described in this booklet consists of:

1. Polaroid 8 x 10 film.

2. The Polaroid 8 x 10 film holder Model 81-06.

3. The Polaroid 8 x 10 film processor.

4. The processor loading tray Model 81-09.

Please note that the film holder Model 81-06 cannot be

used without both the processor and the loading tray

Model 81-09, available separately. For the most up-to-

date film information, see the Film Data sheets at

www.polaroid.com (select Customer Support).

Camera adaptation

To adapt cameras or imaging devices of extra large

format for use with the Polaroid 8 x 10 film holder, some

basic requirements must generally be met:

1. The film holder must be centered on the lens axis.

2. It must lie perpendicular to the lens axis.

3. The film must lie in the same plane in the camera

as the ground glass screen at the time of focusing.

Power supply

The film processor should be operated only at the

voltage indicated on each unit. Processors intended for

use in the U.S. are designed for the 110-120 volt supply.

For countries with a 220-240 volt supply, appropriate

processors are provided.

A power cord is supplied with the processor. When

not in use, the cord can be stored in the special recess

in the base of the processor.

If electricity is not available, the processing rollers can

be operated manually with the manual drive arm.

Instructions for its use are packaged with it. A manual

timer or stopwatch must also be used, because the

electronic timer will not function.

Information and technical assistance

If you should require help with your Polaroid 8 x 10 film

system, or if you have any other photographic problem,

please call us toll free from within the U.S. at 1-800-

225-1618, Monday to Friday, 8 a.m. to 8 p.m. Eastern

Time. Outside the U.S.A., please contact the Polaroid

office nearest you.

Underwriters’ Laboratories, Inc. (UL) requires that

the following safety information be provided in the

U.S.

IMPORTANT SAFEGUARDS

AS WITH ANY ELECTRICALLY OPERATED

EQUIPMENT, BASIC SAFETY PRECAUTIONS

SHOULD BE OBSERVED IN THE USE OF THE

POLAROID 8 X10 FILM PROCESSOR. THESE ARE

PROVIDED AS A REMINDER:

1. FOLLOW ALL INSTRUCTIONS.

2. DO NOT LEAVE UNIT UNATTENDED WHILE IN

USE.

3. IF UNIT WILL NOT BE USED FOR EXTENDED

PERIOD OF TIME, UNPLUG FROM ELECTRICAL

OUTLET. GRASP PLUG, NOT CORD, AND PULL

TO DISCONNECT FROM OUTLET.

4. DO NOT OPERATE UNIT WITH DAMAGED CORD

OR UNIT WHICH HAS BEEN DROPPED OR

DAMAGED, UNTIL IT HAS BEEN EXAMINED BY

AUTHORIZED SERVICE REPRESENTATIVE.

5. DO NOT LET CORD HANG OVER FRONT EDGE

OF TABLE OR COUNTER OR TOUCH HOT

SURFACES.

6. UNIT MUST BE GROUNDED. POWER CORD HAS

THREE-PRONGED GROUNDING PLUG, WHICH

MUST BE PLUGGED INTO APPROPRIATE

OUTLET. DO NOT, UNDER ANY CIRCUM-

STANCES, REMOVE GROUND PRONG FROM

PLUG.

7. IF EXTENSION CORD IS NEEDED, USE

GROUNDED CORD WITH SUITABLE CURRENT

RATING. CORDS RATED FOR LOWER

AMPERAGE THAN UNIT MAY OVERHEAT.

ARRANGE CORD SO THAT IT WILL NOT BE

TRIPPED OVER OR PULLED.

8. TO AVOID ELECTRIC SHOCK HAZARDS, DO NOT

ATTEMPT TO DISASSEMBLE UNIT. FOR

SERVICE OR REPAIR WORK, CONSULT AN

AUTHORIZED POLAROID SERVICE CENTER.

INCORRECT REASSEMBLY CAN CAUSE

ELECTRICAL SHOCK HAZARD WHEN

APPLIANCE IS USED SUBSEQUENTLY. DO NOT

IMMERSE UNIT IN WATER OR OTHER FLUIDS.

DO NOT OPERATE UNIT NEAR WATER OR WITH

WET HANDS.

The Polaroid 8 x 10 System

Please see the photos at the back of the booklet.

The film holder Model 81-06

A. Buttons, to unlatch holder

B. Dark slide (partly removed)

C. Dark slide handle

D. Dark slide stop line

E. Orange tongue, to secure negative envelope

F. Negative guide lines

G. Felt strips (light seal)

The film processor

H. Processing timer

L. Loading tray insertion slot

K. Process button

L. Processing compartment (extended)

M. Lid for processing compartment (partly open)

N. Roller assembly (removable unit)

O. Latches for roller assembly

P. Roller access lid

Q. Processing rollers

R. Location for manual drive arm

The processor loading tray Model 81-09

S. Positive sheet insertion slot

T. Film holder insertion slot

The numbers throughout the text refer to

illustrations at the back of the booklet.

Set up the equipment

When the processor is in its operating position, it will

extend about 30 inches (75 cm) front to back. Select a

working surface which is deep enough. Be sure you also

have enough space to hold the negative and positive

film containers, and for loading the film holder.

Place the processor so that its insertion slot is facing

toward you and is about level with the front edge of the

table (fig. 1). Plug the power cord in at the rear of the

processor (fig. 2) and into the power supply socket.

Swing back the processing compartment and its lid

(fig. 3). The opened compartment must lie horizontally,

as shown, so be sure there is no obstruction behind the

processor which might prevent this.

If your processor is new, and has not been used before,

you must insert the processing roller assembly, which

is packaged separately. Carefully lower the rollers into

the well in the processor (fig. 4). Lower the side near

the timer into place first (fig. 5); the assembly will fit only

when the circular hole is aligned with the circular pin.

Then lower the right side. When the assembly is seated

properly, lock it in place by pushing back the two latches

(fig. 6). Be sure the roller access lid is seated properly

(fig. 7).

Hold the processor loading tray in front of the

processor in the way shown (fig. 8). Insert the tray into

the processor, easing it in gently as far as it will go. It

will then sit snugly against the front edge of the processor

(fig. 9).

The processor is now ready for operation.

Locate the processor in an area that is in subdued

lighting. Also protect the film holder and the film

from strong light as much as possible.

Unnecessarily bright and directional light on

photographic equipment always introduces the

possibility of some light leakage. The heat generated

by strong light can also be harmful to the film.

Cleanliness is important

To get the most satisfactory results, the equipment and

the film must be clean. The following require particular

attention:

1. Processing rollers

You should wipe the rollers before you process each

photograph, to be sure they are free from dust and

other foreign matter. Remove the roller access lid by

pressing down with the thumb at the point indicated (fig.

10) and then lifting it out. Press the process button and

hold it down and, while the rollers rotate, wipe a dry, lint-

free cloth back and forth along the full length of each

roller (fig. 11) Release the process button. Replace the

lid.

Occasionally the rollers may need a more thorough

cleaning. Remove the roller assembly from the

processor and clean the entire length of the rollers (fig.

12), using a dampened cloth if necessary.

Before you reinsert the assembly, remove all dirt and

particles that may have collected in the processor, below

the rollers.

2. Felt strips on film holder

Before you load film, be sure the felt strips on the

film holder are clean. The felt strips (fig. 13) serve as

a light trap. During the use of the holder, these strips

may gradually gather dust. At regular intervals, gently

rub a finger back and forth along the strips, to remove

dust. Alternatively, wipe the full length of each strip very

lightly with the sticky side of a small piece of masking

tape. This will collect dust and other particles that may

have accumulated.

3. Felt strips on loading tray

Below each of the two protrusions indicated by the

arrows (fig.14) there is a short felt strip. These strip are

Product specificaties

Merk:	Polaroid
Categorie:	Fotocamera
Model:	8x10 Film Processor

Heb je hulp nodig?

Als je hulp nodig hebt met Polaroid 8x10 Film Processor stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Fotocamera Polaroid

Polaroid I-2 Handleiding

5 Maart 2024

Polaroid Go 2 Handleiding

8 December 2023

Polaroid Impulse 600 series Handleiding

22 November 2023

Polaroid Instant I-2 Handleiding

22 November 2023

Polaroid SLR 690 Handleiding

14 November 2023

Polaroid NOW+ Generation 2 Handleiding

16 Augustus 2023

Polaroid NOW Generation 2 Handleiding

16 Augustus 2023

Polaroid EE-66 Handleiding

21 Juni 2023

Polaroid EE-33 Handleiding

17 Juni 2023

Polaroid t1035 Handleiding

2 Juni 2023

Handleiding Fotocamera

Nieuwste handleidingen voor Fotocamera

Camouflage EZ2 Handleiding

18 April 2024

Camouflage SM4-PRO Handleiding

18 April 2024

Bushnell Prime L20 Handleiding

13 April 2024

Samsung NX30 Handleiding

9 April 2024

Samsung ST65 Handleiding

8 April 2024

Denver WCT-8026W Handleiding

8 April 2024

Denver WCT-8016 Handleiding

8 April 2024

Ring Stick Up Cam Battery (3rd Generation) Handleiding

6 April 2024

Joy-it rb-camera-ww Handleiding

3 April 2024

Joy-it rb-camera_JT Handleiding

3 April 2024