Planet GT-1205A Handleiding

Planet Niet gecategoriseerd GT-1205A

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet GT-1205A (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET 1-Port 10/100/1000BASE-T

to 2-Port 100/1000BASE-X Media Converter, GT-1205A.

Open the box of the GT-1205A and carefully unpack it. The box

should contain the following items:

Gigabit Media Converter x 1 User's Manual x 1

AC-DC Adapter (Output: 5V DC, 2A max.) x 1

If any item is missing or damaged, please consult the dealer

from whom you purchased your GT-1205A.

Note

The GT-1205A comes with one vacant SFP module

slot. The mini GBIC SFP module is not bundled

with in the package.

Compact in size, easy installation

Co-works with PLANET’s 10”/19” Media Converter Chassis

(MC-700/MC-1500/MC-1500R/MC-1500R48)

Wall mounting and DIN-rail installation supported

 Standard

Complies with IEEE 802.3 10BASE-T

Complies with IEEE 802.3u 100BASE-TX/100BASE-FX

Complies with IEEE 802.3ab 1000BASE-T

Complies with IEEE 802.3z 1000BASE-SX/LX

IEEE 802.3x full-duplex ow control; back pressure for

half duplex to prevent packet loss

3. Hardware Introduction

3.1 Front Panel and LED Indicators

 GT-1205A Front Panel

The GT-1205A consists of two 100/1000BASE-X SFP slots and

one auto-sensing 10/100/1000Mbps Ethernet RJ45 port. Figure

1 shows the front panel of the GT-1205A.

1000

PWR LNK/

ACT

Figure 1: GT-1205A Front Panel

4. Redundancy Overview

The GT-1205A provides rapid ber redundancy of link for highly

critical Ethernet applications. The redundant mode supports

auto-recover function. If the destination port of a packet is

linked down, it will forward the packet to the other port of the

backup pair. The following gure shows the redundant function.

Figure 4: Redundancy Behavior Topology

Link status auto detection and redundancy of dual ports with

the same connector type.

Only the Primary Port is active at a time, the Backup Port is

blocked.

3.2 Rear Panel

The rear panel of the GT-1205A has one DC jack, which

accepts an input power of 5V DC with 2A. The brand-new DIP

switch designed for 1000BASE-X SFP module or 100BASE-FX

SFP module supports on dual SFP slots. The default DIP switch

mode is 1000BASE-X.

SFP Speed

5V DC

1000BASE-X 100BASE-FX

Figure 2: GT-1205A Rear Panel

Caution

Please power off and power on the GT-1205A after

adjusting the DIP switch setting.

Power Information

The center pin diameter of the GT-1205A’s power jack is

2.5mm and the power jack allows an input power of 5V DC.

It conforms to the bundled AC-DC adapter and PLANET’s

media chassis. Should you have any issue about the power

connection, please contact your local sales representative.

Please keep the AC-DC adapter as a spare part when your

GT-1205A is installed to a Media Chassis.

2. Product Features

 Interface

Dual 100/1000BASE-X SFP ber-optic slots

One 10/100/1000BASE-T copper port with auto MDI/MDIX

function

Auto-negotiation for 10/100/1000BASE-T; half-duplex or full-

duplex for 10Mbps and 100Mbps, full-duplex for 1000Mbps

Supports maximum frame size up to 10K jumbo packet

size

IEEE 802.1Q tagged VLAN transparent, multicast passthrough

 Redundancy

Link status auto-detection and redundancy of dual ports

with the same connector type

Allows only the Primary Port or the Backup Port to acti-

vate at a time

- When Primary Port link failure occurs, the trac swaps

to Backup Port automatically

- Once the Primary Port link regains, the trac swaps

from the Backup Port to the Primary Port

- Redundant hardware ber port

 Mechanical

External 5V DC, 2.5A power supply

LED indicators for easy network diagnostics

DIP switch for 100FX or 1000X SFP module supports on

dual SFP slots

DIP switch for 3-port operation in Gigabit switch mode or

redundant mode

 GT-1205A LED Indication

 System

LED Color Function

PWR Green Lit when +5V DC power is detected.

 100/1000BASE-X SFP Slots

LED Color Function

1Green

Lit Indicates that the ber optical port is

linked up.

Blink Indicates that the converter is actively

sending or receiving data over that port.

O Indicates that the ber optical port is

linked down.

2Green

Lit Indicates that the ber optical port is

linked up.

Blink Indicates that the converter is actively

sending or receiving data over that port.

O Indicates that the ber optical port is

linked down.

 10/100/1000BASE-T Port

LED Color Function

LNK/

ACT Orange

Lit Indicates that the copper port is linked up.

Blink Indicates that the converter is actively

sending or receiving data over that port.

O Indicates that the copper port is linked

down.

1000 Green

Lit Indicates that the copper port is

operating at 1000Mbps.

O Indicates that the copper port is linked

down 10/100Mbps or .

2.5mm

DC Receptacle 2.5mm

+5V for each slot

DC receptacle is 2.5mm wide that conforms to the GT-

1205A’s 2.5mm DC jack's central post. Do not install any

improper unit.

The device is a power-required device, meaning it will not work

till it is powered. If your networks should be active all the

time, please consider using UPS (uninterrupted power supply)

for your device. It will prevent you from network data loss or

network downtime.

In some areas, installing a surge suppression device may

also help to protect the GT-1205A from being damaged by

unregulated surge or current.

3.3 Side View

The side panel of the GT-1205A has a DIP switch for setting to

the 3-port switch mode or the 2-port redundant mode. When

“ON” “OFF”, it is in the 2-port redundant mode. And when , it

is in the 3-port switch mode.

OFF ON

Redundant

3-Port Switch OFF

2-Port Redundant ON

Figure 3: GT-1205A Side Panel

When the Primary Port’s link failure occurs, the trac will

swap to Backup Port automatically.

Once the link of the Primary Port is back, the trac will

swap from Backup Port to Primary Port.

5. Installing The Converter

The GT-1205A can be connected over ber optic cabling at a

distance extended from 550 meters to 2km (multi-mode ber)

to 10/20/40/60/80/120 kilometers (single-mode ber or WDM

ber), using the 100/1000BASE-X SFP modules. The SFP

modules are hot-pluggable and hot-swappable. You can plug in

and out the SFP modules to and from any SFP port without

having to power down the GT-1205A.

To install GT1205A, please follow these steps to install the

GT-1205A:

Ethernet Installation

Step 1: Turn o the power of the device/station in a network

to which the GT-1205A will be attached.

Step 2: Ensure that there is no activity in the network.

Step 3: Slide in the 100/1000BASE-X SFP module. Make sure

both sides of the SFP modules are with the same

media type, for example, 100BASE-FX/2km multi-

mode to 100BASE-FX/2km multi-mode, 1000BASE-

SX/550m multi-mode to 1000BASE-SX/550m

multi-mode or 1000BASE-LX/10km single mode to

1000BASE-LX/10km single mode.

- 9 -

- 10 -

- 11 -

- 12 - - 13 -

100/1000BASE-X

LC Fiber 100/1000BASE-X

LC Fiber

100/1000BASE-X

SFP Module

5V DC power

10/100/1000BASE-T

UTP

Figure 5: GT-1205A Gigabit Media Converter Standalone Installation

Step 4: Connect the ber cable. Attach the duplex LC

connector on the network cable to the SFP modules.

Step 5: Attach ber cable from the GT-1205A to the ber

network. TX, RX must be paired at both ends.

Step 6: Connect the 5V DC power adapter to the GT-1205A

and verify that the Power LED lights up.

Step 7: Turn on the power of the device/station; the LINK

LED should light up when all cables are well attached.

Note

1. It is recommended to use PLANET MFB/MGB

series SFP modules for the GT-1205A. If you

insert an SFP module that is not supported, the

GT-1205A will not recognize it. Please check

appendix or go visit our Web site for detailed

specification. http://www.planet.com.tw

2. To prevent from optic acceptor malfunction,

check both the wires and transmitter before

powering on the converter.

6 Cable Connection Parameter

The wiring details are shown below:

Duplex Connection Limitation (max.)

Twisted Pair

Half/Full Node to Node

Node to Switch/Hub 100 meters

Fiber Optic Cables:

Standard

(Wavelength)

100BASE-FX

(1310nm)

1000BASE-SX

(850nm)

1000BASE-LX

(1310nm)

Fiber Type

& Cable

Specications

Multi-mode 50/125μm or

62.5/125μm

Single-mode 9/125μm

7.ProductSpecications

Model GT-1205A

Interface Specications

Hardware Version 4

Ports Copper 1 x 10/100/1000BASE-T port

Fiber 2 x 100/1000BASE-X SFP slots

Note

3. To remove the SFP module, please remove the

fiber connectors in advance and push the belt

or latch of the module. Pull out the module

with force may damage the module and the GT-

1205A.

Media Converter Chassis Installation

To install the GT-1205A in a or standard 10-inch 19-inch

rack, follow the instructions described below.

Step 1: Place your GT-1205A on a hard at surface, with the

front panel positioned towards your front side.

Step 2: Carefully slide in the module until it is fully and rmly

tted into the slot of the chassis; the Power LED of

the GT-1205A will turn ON.

Figure 6: Inserting GT-1205A into an available slot

Caution

1. Never push the converter into the slot with

force; it could damage the chassis.

2. The Media Converter Chassis supports hot-swap;

there is no need to turn off the whole chassis

before sliding in the new converter.

Cable

Twisted-

pair

10BASE-T: 2-pair UTP Cat 3, 4, 5, up to

100 meters

100BASE-TX: 2-pair UTP Cat 5, 5e up to

100 meters

1000BASE-T: 4-pair UTP Cat 5e, 6 up to

100 meters

Fiber-

optic

Cable

1000BASE-SX:

50/125μm or 62.5/125μm multi-mode ber

cable, from 220 and 550 meters to 2km.

1000BASE-LX:

9/125μm single-mode cable, with distance

of 10/20/40/80/120km (vary on SFP

module)

100BASE-FX:

50/125μm or 62.5/125μm multi-mode ber

cable, up to 2km (vary on SFP module)

9/125μm single-mode cable, with distance

for 20/40/60m (vary on SFP module)

Hardware Specications

Switch

Architecture Store and Forward

Flow Control Back pressure for half duplex.

IEEE 802.3x pause frame for full duplex

Fabric 6Gbps

Throughput

(packet per

second)

4.4Mpps

Maximum Packet

Size 10K bytes

LED Display

System: One Power LED (Green)

Fiber Port: Two LNK/ACT LEDs (Green)

TP Port : One Speed LED (Green),

One LNK/ACT LED (Orange)

Dimensions

(W x D x H) 94 x 70 x 26mm

Weight 180g (device only)

Power

Requirement 5V DC, 2A max.

Power

Consumption 2.8 watts/9.5BTU per hour (max.)

Environment

Operating

environment 0 ~ 50 degrees C

Storage

environment -10 ~ 70 degrees C

Operating

Humidity

5 ~ 95%, relative humidity

(non-condensing)

Storage Humidity 5 ~ 95%, relative humidity

(non-condensing)

Standard Conformance

EMI Safety FCC Class B, CE

Standard

Compliance

IEEE 802.3

IEEE 802.3u

IEEE 802.3ab

IEEE 802.3z

IEEE 802.3x

10BASE-T

100BASE-TX/100BASE-FX

1000BASE-T

1000BASE-SX/LX

Flow Control

PLANET TECHNOLOGY CORPORATION

e-mail: sales@planet.com.tw http://www.planet.com.tw

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219 2219 9528-9518 Fax:886-2- -

EC Declaration of Conformity

For the following equipment:

*Type of Product : 10/100/1000B -T to Dual 1000B -ASE ASE X SFP Media Converter

*Model Number : GT-1205A

* Produced by:

Manufacturer‘s Name : Planet Technology Corp.

Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,

New Taipei City 231, Taiwan R.O.C.

is herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Laws of the Member States relating to Electromagnetic Compatibility

Directive on 2014/30/EU.

For the evaluation regarding the EMC, the following standards were applied:

EN 55032 (2015)

EN 61000-3-2 (2014)

EN 61000-3-3 (2013)

EN 55024 ( : 2015) 2010 + A1

R esponsible for marking this declaration if the:

Manufacturer Authorized representative established within the EU 

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan R.O.C.

Person responsible for making this declaration

Name, Surname Kent Kang

Position / Title : Director

Taiwan

23, 2019 Aug.

Place

Date

Legal Signature

Product specificaties

Merk:	Planet
Categorie:	Niet gecategoriseerd
Model:	GT-1205A
Kleur van het product:	Zwart
Gewicht:	180 g
Breedte:	94 mm
Diepte:	70 mm
Hoogte:	26 mm
LED-indicatoren:	Ja
Stroom:	2 A
Connectiviteitstechnologie:	Bedraad
Aantal Ethernet LAN (RJ-45)-poorten:	1
Certificering:	FCC Class B, CE
Plug and play:	Ja
Ingangsspanning:	5 V
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Netwerkstandaard:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Temperatuur bij opslag:	-10 - 70 °C
Intern:	Nee
Golflengte:	- nm
Luchtvochtigheid bij opslag:	5 - 95 procent
Ethernet interface type:	Gigabit Ethernet
Maximale overdrachtssnelheid van gegevens:	1000 Mbit/s
Auto MDI/MDI-X:	Ja
Maximaal bereik:	120000 m
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Code geharmoniseerd systeem (HS):	85176990
DIN rail bevestiging:	Ja
Vezel-optische connector:	SFP
Converter input interface:	1000Base-T
Duplex systeem:	Full, Half
Converter output interface:	1000Base-X
Fibre channel-poorten:	2