Pioneer DVH-P5000MP Handleiding

Pioneer Autoradio DVH-P5000MP

Lees hieronder de 📖 handleiding in het Nederlandse voor Pioneer DVH-P5000MP (88 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/88
MANUEL D’INSTALLATION
DVH-P5000MP
INSTALLATION MANUAL
This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
Dieses Produkt entspricht den neuen kabelfarben.
Le code de couleur des câbles utilisé pour ce produit est
nouveau.
Questo prodotto è conforme ai nuovi codici colori.
De kleuren van de snoeren van dit toestel zijn gewijzigd.
English Español Deutsch Français Italiano Nederlands
Connecting the Units
Power cable connection 4
Connecting to separately sold power amp 6
When connecting with a multi-channel
processor 8
When connecting the display with RCA
input jack 10
When using a display connected to rear
video output 11
Installation
DIN Front/Rear-mont 12
DIN Front-mont 13
Installation with the rubber bush 13
Removng the unit 13
DIN Rear-mont 14
Installation using the screw holes
on the side of the unit 14
Fixing the front panel 15
Notes
• This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in
a recreational vehicle, truck, or bus, check the
battery voltage.
• To avoid shorts in the electrical system, be
sure to disconnect the ≠battery cable before
beginning installation.
• Refer to the owner’s manual for details on
connecting the power amp and other units,
then make connections correctly.
• Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against
metal parts.
• Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift,
handbrake, and seat rails. Do not route wiring
in places that get hot, such as near the heater
outlet. If the insulation of the wiring melts or
gets torn, there is a danger of the wiring short-
circuiting to the vehicle body.
• Don’t pass the yellow lead through a hole into
the engine compartment to connect to the
battery. This will damage the lead insulation
and cause a very dangerous short.
• Do not shorten any leads. If you do, the pro-
tection circuit may fail to work when it should.
• Never feed power to other equipment by cut-
ting the insulation of the power supply lead of
the unit and tapping into the lead. The current
capacity of the lead will be exceeded, causing
overheating.
• When replacing fuse, be sure to use only fuse
of the rating prescribed on the fuse holder.
• Since a unique BPTL circuit is employed,
never wire so the speaker leads are directly
grounded or the left and right ≠speaker
leads are common.
Contents Connecting the Units
2En
• Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speak-
ers with output and/or impedance values
other than those noted here may result in the
speakers catching fire, emitting smoke, or
becoming damaged.
• If the RCA pin jack on the unit will not be
used, do not remove the caps attached to the
end of the connector.
• When this product’s source is switched ON, a
control signal is output through the
blue/white lead. Connect to an external power
amp’s system remote control or the car’s
Auto-antenna relay control terminal (max. 300
mA 12 V DC). If the car features a glass
antenna, connect to the antenna booster
power supply terminal.
• When an external power amp is being used
with this system, be sure not to connect the
blue/white lead to the amp’s power terminal.
Likewise, do not connect the blue/white lead
to the power terminal of the auto-antenna.
Such connection could cause excessive cur-
rent drain and malfunction.
• To avoid short-circuiting, cover the discon-
nected lead with insulating tape. Especially,
insulate the unused speaker leads without
fail. There is a possibility of short-circuiting if
the leads are not insulated.
• To prevent incorrect connection, the input
side of the IP-BUS connector is blue, and the
output side is black. Connect the connectors
of the same colors correctly.
• If this unit is installed in a vehicle that does
not have an ACC (accessory) position on the
ignition switch, the red lead of the unit should
be connected to a terminal coupled with igni-
tion switch ON/OFF operations. If this is not
done, the vehicle battery may be drained
when you are away from the vehicle for sev-
eral hours.
• The black lead is ground. Please ground this
lead separately from the ground of high-cur-
rent products such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of
damage to the products or fire.
• Cords for this product and those for other
products may be different colors even if they
have the same function. When connecting
this product to another product, refer to the
supplied Installation manuals of both prod-
ucts and connect cords that have the same
function.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
En 3
English Español Deutsch Français Italiano Nederlands
Connecting the Units


Product specificaties

Merk: Pioneer
Categorie: Autoradio
Model: DVH-P5000MP

Heb je hulp nodig?

Als je hulp nodig hebt met Pioneer DVH-P5000MP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autoradio Pioneer

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio