Philips MG7965 Handleiding

Bekijk gratis de handleiding van Philips MG7965 (2 pagina’s), behorend tot de categorie Grooming set. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.4 sterren uit 5 reviews. Heb je een vraag over Philips MG7965 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Manufactured for: Philips Personal Health

a division of Philips North America LLC

P.O. Box 10313, Stamford, CT 06904, USA

This symbol on the product’s nameplate means

it is listed by Underwriters’ Laboratories, Inc.

Norelco is a registered trademark of Philips North

America LLC.

PHILIPS and Philips shield are registered trademarks of

Koninklijke Philips N.V.

©2025 Philips North America LLC. All rights reserved.

3000.150.3795.2 (01/05/2025)

English

IMPORTANT SAFETY INSTRUCTIONS

When using an electric product, basic precautions

should always be followed, including the following:

Read all instructions before using this product.

DANGER

To reduce the risk of electric shock:

-To charge the product, only use a USB power

source on a certied product with output

rating 5V, ≥ 1A. For safe charging in a moist

environment (e.g. in a bathroom), only use an

IPX4 (splash-proof) power source. A suitable

power source (e.g. Philips HQ87) is available via

www.philips.com/support. If you need support

nding the correct USB power source, contact

Philips support at 1-800-243-3050. Using a non-

certied USB power source may cause hazards or

serious injuries.

-Keep the USB cable, the USB power source and the

charging stand (if provided) dry.

-Do not reach for a corded product that has fallen

into water. Unplug immediately from the power

outlet.

-Do not place or store the product where it can

fall or be pulled into a tub or sink. Do not place or

drop the product into water or other liquid.

-This product does not work while it is connected

to the power outlet. Except when charging, always

unplug this product from the power outlet.

-Remove USB power source from power outlet and

product before cleaning the product with water.

WARNING

To reduce the risk of burns, re, electric shock, or

injury to persons:

-This product is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

product by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the product.

-Use this product only for its intended household

use as described in this manual. Misuse can lead to

hazards or serious injuries. Do not use attachments

not recommended by Philips North America LLC.

-Never operate this product if it has a damaged

USB power source, if it is not working properly,

after it has been dropped or damaged, or after

the product or the USB power source has been

dropped into water. For assistance call 1-800-243-

3050.

-Keep the USB cable and the USB power source

away from heated surfaces.

-Never drop or insert any object into any opening.

-Do not use the USB power source in or near a

power outlet that contains an electric air freshener

to prevent damage to the USB power source.

-Do not use product outdoors or operate where

aerosol (spray) products are being used or where

oxygen is being administered.

-Always check cutting units and other attachments

and accessories before you use the product. Never

use the product with a damaged cutting unit,

attachment or accessory, as injury may occur.

-Always attach the USB cable to the USB power

source and the product rst, then attach the USB

power source to the power outlet. To disconnect,

set all controls to 'o' position. Then remove the

USB power source from the power outlet.

-Plug USB power source directly into power outlet.

Do not use an extension cord.

-Unplug USB power source before plugging in or

unplugging the product.

-The batteries used in this product may present

a re or chemical burn hazard if mistreated. Do

not disassemble, heat above 100°C (212°F) or

incinerate.

-Only use original Philips accessories or

consumables.

-Charge, use and store the product at a

temperature between 50 °F / 10°C and 95 °F /

35°C.

-Keep product and batteries away from re and

do not expose them to direct sunlight or high

temperatures.

-If the product becomes abnormally hot or smelly,

changes color or if charging takes longer than

usual, stop using and charging the product and

contact Philips.

-Do not place products and their batteries in

microwave ovens or on induction cookers.

-Do not open, modify, pierce, damage or dismantle

the product or battery to prevent batteries

from heating up or releasing toxic or hazardous

substances. Do not short-circuit, overcharge or

reverse charge batteries.

-If batteries are damaged or leaking, avoid contact

with the skin or eyes. If this occurs, immediately

rinse well with water and seek medical care.

-When you handle batteries, make sure that your

hands, the product and the batteries are dry.

-To avoid accidental short-circuiting of batteries

after removal, do not let battery terminals come

into contact with metal objects (e.g. coins,

hairpins, rings). Do not wrap batteries in aluminum

foil. Tape battery terminals or put batteries in a

plastic bag before you discard them.

SAVE THESE INSTRUCTIONS

Introduction

Congratulations on your purchase and welcome to

Philips Norelco!

To fully benet from the support that Philips

Norelco oers, register your product at:

www.norelco.com/register.

You can nd the model number on the back of your

product.

The full model number (e.g. MG1234/56) is located

on the bottom of the packaging, your receipt or order

conrmation.

IMPORTANT TO KNOW

-This product is waterproof. It is suitable for use in

the bath or shower and for cleaning under the tap.

For safety reasons, the product can therefore only

be used without cord.

-The guards provided with the product have

dierent colors depending on their intended use.

Select the type of guard suitable for the part of the

body that you want to trim.

-Switch o the product before removing or

attaching attachments and before cleaning.

-Clean the product after each use (see 'Cleaning').

This product has no other user-serviceable parts. For

assistance call 1-800-243-3050.

Features (Fig. 1)

1 Nose and ear hair trimmer

2 Precision shaver (only with models MG7970,

MG7975)

3 Precision trimmer

4 Extra-wide hair trimmer

5 Travel lock attachment (only with models

MG7965, MG7975)

6 Full-size hair trimmer

7 On/o button

8 Battery status indicator

9 Socket for small plug of USB cable

10 USB cable

Note: A suitable power source (e.g. Philips HQ87)

is available via www.philips.com/support.

11 Stubble guard 1 mm (3/64in.) (only with model

MG7970)

12 Stubble guard 2 mm (5/64in.) (only with model

MG7970)

13 Beard guard 5 mm (3/16 in.) (only with model

MG7965)

14 Beard guard 7 mm (9/32 in.) (only with model

MG7965)

15 Long beard guard 9 mm (23/64 in.) (only with

model MG7970)

16 Precision trimming guard 1 mm – 3 mm (3/64 in.

– 1/8 in.)

17 Adjustable beard and hair guard 3 mm – 7

mm(1/8 in. – 9/32 in.) (only with models MG7970,

MG7975)

18 Eyebrow guard 6 mm (1/4 in.)

19 Hair guard 4 mm (5/32 in.)

20 Hair guard 9 mm (3/8in.)

21 Hair guard 12 mm (15/32in. (12mm)

22 Hair guard 16 mm (21/32in.)

23 Fading hair guard 4mm – 9mm (5/32 in.– 3/8in.)

24 Fading hair guard 9mm – 4mm (3/8in. – 5/32in.)

25 Body guard 3 mm (1/8in.)

26 Body guard 5 mm (3/16in.)

27 Skin Protect guard 0.5 mm (1/32 in.) (only with

models MG7965, MG7975)

Not shown: cleaning brush, styling comb and pouch.

Charging

-Charging or using the product at temperatures

below 50 °F / 10 °C or higher than 95 °F / 35 °C

adversely aects the lifespan of the battery.

-If the product is subjected to a major change in

temperature, pressure or humidity, let the product

acclimatize for 30 minutes before use.

-The USB power source is not included. To safely

charge your product, only use a certied IPX4

power source with output rating 5 V, ≥ 1.

Charging with USB power source

Charge the product before rst use and when the

battery status indicator shows that the battery is

almost empty. When the product has charged for

3 hours, it has a cordless operating time of up to 5

hours.

Warning: Keep the USB cable and the USB

power source dry.

1 Make sure the product is switched o.

2 Insert the small plug of the USB cable into the

socket in the bottom of the product (Fig. 2).

3 Insert the USB plug into the USB power source (not

included) (Fig. 3).

4 Insert the USB power source into the power outlet

(Fig. 4).

5 After charging, pull the small plug out of the

product and remove the USB power source from

the power outlet.

Quick charge

After approx. 5 minutes of charging, the product

contains enough power for one trimming session.

Battery status indications

Battery statusIndicator mode

Almost emptyFlashing orange light

ChargingFlashing white light

Fully chargedSolid white light

Note: Approx. 30 minutes after the battery is fully

charged, the battery status indicator switches o

automatically.

MG7970

MG7965

,

MG7975

,

Using the product

Always check the product and all accessories

before you use it. Do not use the product or any

accessory if it is damaged, as this may cause injury.

Always replace a damaged part with one of the

original type.

Because of hygiene, only one person should use

the product.

Trimming tips

-When trimming for the rst time, start by using the

guard with the maximum trimming length setting

to familiarize yourself with the product.

-Since all hairs do not grow in the same direction,

you may want to try dierent trimming directions

(i.e. upwards, downwards, or across). Practice is

best for optimum results.

-Always make smooth and gentle movements and

make sure that the surface of the guard always

stays in contact with your skin.

-For best results, use the product on clean, dry hair,

as wet hair tends to stick to the body.

-When too many hairs have accumulated on the

product, remove the hairs before and/or during

use, for best trimming results (see 'Cleaning').

Detaching and attaching cutting elements

1 To detach a cutting element, place your thumb

below the teeth of the cutting element and gently

push upwards until the cutting element comes o

the handle (Fig. 5).

2 To attach a cutting element, insert the plastic

notch at the back of the cutting element into the

guiding slot in the handle. Then gently press the

teeth of the cutting element downwards until the

cutting element clicks into place (Fig. 6).

Detaching the nose and ear hair trimmer

1 Place your nger on the recess at the back of the

attachment and push the attachment o the

handle (Fig. 7). Use your other hand to prevent the

attachment from dropping on the oor.

Attaching and detaching guards

1 To attach any type of guard onto the cutting

element,slide the front part of the guard onto the

teeth and press the plastic notch at the back of the

guard downwards until it clicks into place (Fig. 8).

2 To detach any type of guard from the cutting

element, carefully push its back part o the

product and then slide it o the cutting element

(Fig. 9).

Guard colors

The guards provided with the product have dierent

colors depending on their intended use. Select the

type of guard suitable for the part of the body that

you want to trim.

Guard

color

Intended useCutting

element

BlueSkin Protect guardFull-size hair

trimmer

BlackBeard and scalp hairFull-size hair

trimmer

Medium

gray

Scalp hairExtra-wide hair

trimmer

Light grayEyebrows

Full-size hair

trimmer

GreenBodyFull-size hair

trimmer

Switching the product on and o

1 Press the on/o button once to switch the product

on or o (Fig. 10).

Attachments for use on beard

Always comb your beard or moustache with a ne

comb before you start trimming.

Full-size hair trimmer

Use the full-size hair trimmer without a guard to trim

hair close to the skin (to a length of 1/32in./0.5mm)

or to create clean lines around your beard, neck and

sideburns.

1 To trim hair close to the skin, place the at side of

the cutting element against your skin and make

strokes against the direction of hair growth (Fig.

11).

2 For contouring, hold the cutting element

perpendicular to the skin and move it upwards or

downwards with gentle pressure (Fig. 12).

Trimming with the Skin Protect guard (only

MG7965, MG7975)

Attach the Skin Protect guard to the full-size hair

trimmer to trim your beard close to the skin (to a

length of 1/32in./0.5mm) for extra protection of the

skin.

Beard guards

Attach a black beard guard to the full-size hair

trimmer to trim your beard and mustache evenly to

the desired length (see 'Attaching and detaching

guards'). The numbers on the guards relate to the

number of millimeters of hair length that will remain

after trimming.

1 Attach a beard guard to the full-size hair trimmer.

2 To trim in the most eective way, move the guard

against the direction of hair growth (Fig. 11). Make

sure that the surface of the guard always stays in

contact with the skin.

Attachments for use on beard and head

Precision trimming guard

Attach the black precision trimming guard to the

full-size hair trimmer to trim your beard or hair to a

short length ranging from 1/25 in. to 1/8 in. (1 mm –

3 mm).

1 Attach the precision trimming guard to the full-

size hair trimmer (see 'Attaching and detaching

guards').

2 Scroll the wheel on the guard to set the length

(Fig. 13). The numbers on the guard relate to the

number of millimeters of hair length that will

remain after trimming.

3 To trim in the most eective way, move the guard

against the direction of hair growth (Fig. 11). Make

sure that the surface of the guard always stays in

contact with the skin.

Adjustable beard and hair guard

Attach the black adjustable beard and hair guard to

the full-size hair trimmer to trim your beard or hair

evenly to a length ranging from 1/8 in. to 9/32 in. (3

mm – 7 mm) (see 'Attaching and detaching guards').

1 Attach the adjustable beard and hair guard to the

full-size hair trimmer.

2 Use the slide switch on the guard to adjust the

length (Fig. 14). The numbers on the guard relate

to the number of millimeters of hair length that

will remain after trimming.

3 To trim in the most eective way, move the guard

against the direction of hair growth (Fig. 11). Make

sure that the surface of the guard always stays in

contact with the skin.

Attachments for use on head

Always comb your hair before you start trimming.

For best results, use the product on clean, dry hair.

Extra-wide hair trimmer

Use the extra-wide hair trimmer without a guard

to trim the hair on your head very close to the skin

(1/32in /0.5mm) or to contour the neckline and area

around the ears.

1 To contour the hairline around the ears, comb the

hair ends over the ears. Tilt the product in such a

way that only one edge of the cutter teeth touches

the hair ends when you shape the contours

around the ears.

2 To contour the nape of the neck or sideburns, turn

the product and make downward strokes (Fig. 15).

Move the product slowly and smoothly following

the natural hairline.

Hair guards

Attach a medium gray hair guard to the extra-wide

hair trimmer to evenly trim the hairs on your head

(see 'Attaching and detaching guards'). The numbers

on the guards relate to the number of millimeters of

hair length that will remain after trimming.

1 Attach a hair guard to the extra-wide trimmer.

2 Move the trimmer slowly over the crown from

dierent directions to achieve an even result. Make

sure that the surface of the guard always stays in

contact with the skin.

3 Always move the trimmer against the direction of

hair growth (Fig. 16). Press lightly.

4 Make overlapping passes over the head to ensure

that all hair that should be cut has been cut.

5 Gently shake the hairs o the product in between

strokes to prevent hairs from collecting between

the cutting element and the guard.

Fading hair guards

Attach a dark gray fading hair guard to the extra-wide

hair trimmer to create a fade line around the ears. The

product comes with 2 fading hair guards. Use both

guards to trim hair around both ears. Choose a guard

based on the preferred trimming direction of back to

front or front to back.

1 Attach one fading hair guard to the extra-wide

hair trimmer to trim the hair around the ear (see

'Attaching and detaching guards').

2 Place the trimmer on your hair close to the ear.

Place the trimmer at the back or front of your ear,

depending on the trimming direction you prefer.

Always make sure that the side of the guard with

the short teeth is closest to your ear (Fig. 17).

3 Move the trimmer slowly around the ear, while

holding it steady.

4 Repeat the movement several times around one

ear to make sure that all the hair that should be

cut has been cut to a fade. Then attach the other

fading hair guard to trim the hair around the other

ear.

5 Gently shake the hairs o the product in between

strokes to prevent hairs from collecting between

the cutting element and the guard.

Attachments for use on body

Always use a body guard when you trim sensitive

areas.

Body guards

Attach a green body guard to the full-size hair

trimmer to trim hairs below the neckline. The numbers

on the guards relate to the number of millimeters of

hair length that will remain after trimming.

1 Attach a body guard to the full-size hair trimmer

(see 'Attaching and detaching guards').

2 To trim in the most eective way, stretch the skin

with your free hand and move the guard against

the direction of hair growth (Fig. 18). Make sure

that the surface of the guard always stays in

contact with the skin.

Precision attachments for use on face

Precision trimmer

Use the precision trimmer to create ne lines and

contours around your facial style close to the skin, to a

length of 1/32in. (0.5mm).

1 Hold the precision trimming head perpendicular to

the skin and move the trimming head upwards or

downwards with gentle pressure (Fig. 19).

Eyebrow guard

Use the light gray eyebrow guard to tidy up eyebrows

or trim sideburns to a length of 1/4in. (6mm).

1 Attach the light gray eyebrow guard to the full-

size hair trimmer (see 'Attaching and detaching

guards').

2 Comb your eyebrows in the direction of hair

growth.

3 Slowly move the trimmer against the hair growth

direction. Press lightly and make sure that the

surface of the guard always stays in contact with

the skin (Fig. 20).

Nose and ear hair trimmer

Use the nose and ear hair trimmer to trim your nose

and/or ear hair.

-Make sure nasal passages are clean. Make sure

outer ear canals are clean and free from wax.

-Do not insert the cutting element too deep into

your nostrils or ear canals (max. 3/16 in. or 5 mm).

-When trimming both nose and ear hair, make

rm, rotary movements to ensure that the cutting

element reaches all the hairs.

-Clean the nose and ear hair trimmer after each use

(see 'Cleaning the nose and ear hair trimmer').

Note: The nose and ear hair trimmer is designed not

to clean-shave your nostrils or ear canals, but to cut

the hairs to a shorter length. Nose and ear hairs have

important protective functions and should not be fully

removed.

Trimming nose hair

1 Gently insert the cutting element into one of the

nostrils. Move the tip in and out of the nostril in

a rm, rotary motion to cut the hairs to a shorter

length (Fig. 21).

Trimming ear hair

1 Slowly move the cutting element along the outer

ear to trim hairs that stick out beyond the rim.

2 Gently insert the cutting element into the outer

ear canal. Move the tip in and out of the outer ear

canal in a rm, rotary motion to cut the hairs to a

shorter length (Fig. 21).

Precision shaver

Use the precision shaver after trimming to shave

unwanted hairs on cheeks, chin and along the beard

with precision. Make sure to pre-trim your beard

rst, with the full-size hair trimmer without guard, to

obtain the best result.

Use the precision shaver to remove remaining hairs

and for detailing your beard style. The precision

shaver is not suitable for a full face shave.

1 Gently press the precision shaver onto the skin

and shave along contoured edges to remove any

unwanted hairs (Fig. 22).

Cleaning

Switch o the product before removing or

attaching attachments and before cleaning.

Only use cold or lukewarm water to clean the

product.

Never use scouring pads, abrasive cleaning agents

or aggressive liquids such as gasoline or acetone to

clean the product.

Never dry the cutting element with a towel or

tissue, as they may get caught in the teeth and

cause damage.

After every use: cleaning under the tap

1 Make sure that the product is switched o and

that the USB power source has been removed

from the power outlet and from the product.

2 Remove any guard (see 'Attaching and detaching

guards') and cutting element (see 'Detaching and

attaching cutting elements') from the product.

3 Remove any hairs that have accumulated in the

hair chamber with the cleaning brush supplied.

4 Clean the cutting element and guard under

running tap water (Fig. 23).

5 Carefully shake o excess water and let all parts

air-dry completely.

Cleaning the nose and ear hair trimmer

Clean the nose and ear hair trimmer immediately after

use and when a lot of hair or dirt has accumulated on

the cutting element.

1 Rinse the nose and ear hair trimmer head under

running tap water (Fig. 24).

2 Switch on the product and rinse the cutting

element once more to remove any remaining

hairs. Then switch o the product again.

For a thorough clean, detach the nose and ear hair

trimmer head from the product and immerse it in

a bowl with warm water for a few minutes to soak

and soften the debris. Reattach the nose and ear

trimmer head and turn on the product to rinse o

stubborn hair/debris.

3 Carefully shake o excess water and let all parts

air-dry completely.

Cleaning the precision shaver

1 Hold the precision shaver at the grooves on each

side and pull the top part o the bottom part.

2 Blow and/or shake out any hair that has

accumulated inside the precision shaver.

3 Clean the top part of the precision shaver under

running tap water (Fig. 25).

4 Carefully shake o excess water and let all parts

air-dry completely.

5 Reattach the top part onto the bottom part of the

precision shaver.

Storage

Do not place or store the product where it can fall or

be pulled into a tub or sink, water or other liquid.

-Make sure that the product is switched o and

that the USB power source has been removed

from the power outlet and from the product.

-Do not wrap the USB cable around the product

when storing.

-Store the product, the USB power source and all

the accessories in the pouch supplied. Place the

pouch in a safe, dry location, where it will not be

crushed, banged, or subject to damage.

-Make sure that the product and the accessories

are dry before you store them in the pouch.

Travel lock attachment

Attach the travel lock attachment onto the full-size

hair trimmer to prevent the product from accidentally

switching on (Fig. 26).

Assistance

For assistance, visit our website:

www.philips.com/support or call toll free 1-800-

243-3050.

Disposal

-This product contains a rechargeable lithium-ion

battery which must be disposed of properly.

-Contact your local town or city ocials for battery

disposal information. You can also call 1-800-822-

8837 or visit: for battery www.call2recycle.org

drop-o locations (Fig. 27).

-For assistance, visit our website

www.philips.com/support or call 1-800-243-

3050 toll free.

-Your product is designed and manufactured with

high quality materials and components, which can

be recycled and reused. For recycling information,

please contact your local waste management

facilities or visit: .www.recycle.philips.com

Full Two-Year Warranty

Philips North America LLC warrants this new product

(except cutters and guards) against defects in

materials or workmanship for a period of two years

from the date of purchase, and agrees to repair or

replace any defective product without charge.

IMPORTANT: This warranty does not cover damage

resulting from accident, misuse or abuse, lack of

reasonable care, the axing of any attachment

not provided with the product or loss of parts or

subjecting the product to any but the specied

voltage or batteries.*

NO RESPONSIBILITY IS ASSUMED FOR ANY

SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES.

In order to obtain warranty service, simply go to

www.philips.com/support for assistance. It is

suggested that for your protection you return

shipments of product by insured mail, insurance

prepaid. Damage occurring during shipment is not

covered by this warranty.

NOTE: No other warranty, written or oral, is

authorized by Philips Personal Health, a division of

Philips North America LLC.

This warranty gives you specic legal rights, and you

may also have other rights which vary from state

to state. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so

the above exclusion and limitations may not apply to

you.

*Read enclosed instructions carefully.

45-DAY MONEY-BACK GUARANTEE

If you are not fully satised with your product send

the product back and we’ll refund you the full

purchase price.

The product must be shipped prepaid by insured

mail, insurance prepaid, have the original sales

receipt, indicating purchase price and date of

purchase.

We cannot be responsible for lost mail.

The product must be postmarked no later than 45

days after the date of purchase. Philips reserves

the right to verify the purchase price of the

product and limit refunds not to exceed suggested

retail price.

To obtain the money-back guarantee service,

please go to www.PhilipsMoneyBack.com and

follow the simple 3-step process.

Delivery of refund check will occur 6–8 weeks after

receipt of returned product.

Español

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD

Cuando utilice un producto eléctrico, siempre

debe seguir las precauciones básicas, incluidas las

siguientes:

Lea todas las instrucciones antes de usar este

producto.

PELIGRO

Para reducir el riesgo de descarga eléctrica:

-Para cargar el producto, use solo una fuente de

alimentación USB en un producto certicado

con valores de salida de 5V, ≥ 1A. Para la carga

segura en ambientes húmedos (por ejemplo, en

un baño), use solo una fuente de alimentación

IPX4 (a prueba de salpicaduras). Una fuente

de alimentación adecuada (por ejemplo,

Philips HQ87) se encuentra disponible en

www.philips.com/support. Si necesita asistencia

encontrando la fuente de alimentación USB

correcta, comuníquese con asistencia de Philips al

1-800-243-3050. Usar una fuente de alimentación

USB no certicada podría causar lesiones graves o

peligrosas.

-Mantenga el cable USB, la fuente de alimentación

USB y la base de carga (si viene incluida) secos.

-No intente agarrar un producto con cable que

haya caído al agua. Desconéctelo inmediatamente

del enchufe de la pared.

-No coloque ni guarde el producto en un lugar

desde donde pueda caerse a una bañera o

fregadero. No coloque el producto en un lugar

desde donde pueda caerse al agua o a cualquier

otro líquido ni sumerja el producto en ningún tipo

de líquido.

-Este producto no funciona mientras está

conectado al enchufe de pared. Excepto cuando se

esté cargando, siempre desenchufe este producto

del enchufe de pared.

-Desconecte la fuente de alimentación USB del

tomacorriente y del producto antes de limpiar el

producto con agua.

ADVERTENCIA

Para reducir el riesgo de quemaduras, incendio,

descarga eléctrica o lesiones:

-Este producto no está destinado a personas

(adultos o niños) con capacidades física, sensorial

o mental disminuidas, o que no tengan los

conocimientos o la experiencia necesarios, a

menos que una persona responsable de su

seguridad los supervise o los instruya sobre el uso

del producto. Evite que los niños jueguen con este

producto.

3/64 in.

1 mm

1/16 in.

2mm

3/8 in.

9 mm

3/16 in.

5 mm

9/32 in.

7 mm

1/4 .in

6 mm

3/64 in. – 1/8 in.

1 mm – 3 mm

1/8 in. – 9/32 in.

3 mm – 7 mm

1/8 .in

3 mm

3/16 in.

5 mm

5/32 in. – 3/8 in.

4 mm – 9 mm

5/32 in.

4 mm

3/8 in.

9 mm

15/32 in.

12 mm

21/32 in.

16 mm

1/32 in.

0.5 mm

3

4

1

2

5

6

7

8

11

13

15

16

17

18

2324

20

22

26

12

14

19

21

25

27

9

10

NOT INCLUDED

1

2

NOT INCLUDED

1

2

= mm

1

2

= mm

2

5

8

11

14

17

20

23

26

3

6

9

12

15

18

21

24

27

4

7

10

13

16

19

22

25

1

Product specificaties