Perlick 3076 Handleiding
Bekijk gratis de handleiding van Perlick 3076 (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 17 mensen en kreeg gemiddeld 5.0 sterren uit 9 reviews. Heb je een vraag over Perlick 3076 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
Installation Instructions
Air-Cooled Wall Mount Beverage Dispenser
Form No. Z2507
Rev. 11.30.2022
Air Cooled Wall Mount Dispenser Installation Instructions
2
Installation of Air cooled Wall Mount Dispenser
1. Remove screws which
secure the back plate
to the dispenser.
3. Remove screws which
secure the bottom plate to
the dispenser.
Remove bottom plate and
set aside.
Parts Bag Included with Tower:
2. Remove back
plate and set aside.
Preparing for Installation:
Black Poly-tape Clear poly-tape
Elbow drain
tting with
barbed tailpiece
Straight drain
tting with
barbed tailpiece Spanner wrench
Parts bag contents include –
Included with Tower:
Wall Mount Dispenser
(Faucets and tap handles
shown are not included)
Mounting Bracket
Other Parts Needed for Installation: The parts required will vary depending on the installation.
PART NO. DESCRIPTION
C26609 Wall Mounted Air Shaft Connector, Cooler (1 required)
1655R Blower Kit, 134 CFM
C15365-1 3” Hose duct, blower to air shaft inside cooler - 12.5 feet
C15365-2 3” Hose duct, blower to air shaft inside cooler - 25 feet
C15366-1 Coupling Sleeve for 3” air shaft tube (1 required when joining two 12” sections)
C31573 Poly housing hanger strap kit
61082-1 Aluminum housing hanger
1390D 1/2” I.D. Vinyl Drain Tube – Anti-Microbial
Air Cooled Wall Mount Dispenser Installation Instructions
Form No. Z2507
Rev. 11.30.2022
3. Determine mounting location for dispensing
unit on wall.
Secure bracket to the wall.
Note: Align screws with as many wall studs
as possible to provide adequate support for
the dispenser.
After installing one screw, check to insure the
bracket is perfectly level before installing
remaining screws.
Note: Use mounting screws and anchors if
needed which are appropriate for the wall the
dispenser is to be installed on.
4. Hang back plate on the installed hanging track
making sure the plate is centered on the track.
Trace holes onto wall.
Remove back plate and set aside.
5. Measure to locate the exact center of each hole
location.
Mark centers.
6. Cut holes for air tube and beverage leads with
a 3-1/2” to 4” hole saw. The hole is larger than the
diameter of the air inlets on the dispensing units
to provide clearance when lowering the dispenser
into position.
Product specificaties
| Merk: | Perlick |
| Categorie: | Niet gecategoriseerd |
| Model: | 3076 |
Heb je hulp nodig?
Als je hulp nodig hebt met Perlick 3076 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Perlick
9 December 2024
9 December 2024
9 December 2024
22 Augustus 2024
22 Augustus 2024
5 Augustus 2024
5 Augustus 2024
5 Augustus 2024
5 Augustus 2024
5 Augustus 2024
Handleiding Niet gecategoriseerd
- Losi
- Stelton
- Falmec
- Toomax
- Twinkly
- Parallels
- Texas
- Oatey
- Corel
- MediaMatrix
- Kipor
- DriverGenius
- Pro-Ject
- Pelgrim
- Schleich
Nieuwste handleidingen voor Niet gecategoriseerd
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025