Panduit FMT1A Handleiding

Panduit Niet gecategoriseerd FMT1A

Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit FMT1A (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

CONTENTS: (#) indicates FMT2A quantity

OPTICOM QUICKNET Rack Mount Angled Fiber

Cassette Enclosures and Patch Panels

Part Numbers: FMT1A, FMT2A, CFAPPBL1A, CFAPPBL2A

1 - ENCLOSURE

1 (2) - #10-32 x 5/16" SCREWS

4 (5) - #10-32 HEX NUTS

4 - #12-24 x 1/2" SCREWS

4 - M6 x 1 SCREWS

3 - #10 FLAT WASHERS

1 (2) - CABLE ENTRY GROMMET(S)

1 (2) - STRAIN RELIEF BRACKET(S)

2 - ADHESIVE BEVEL ENTRY CLIPS

2 - ADHESIVE BACKED MOUNTS

4 - TAK-TYs (6" pcs.)

2 - SLACK SPOOLS (FMS1 or FMS2)

Cover (field removable)

Fiber Adapter Panels (FAPs):

Up to 4 for FMT1A

Up to 8 for FMT2A

(sold separately) Trunk or Interconnect

Cable Entry Grommet

Strain Relief Bracket

Enclosure

CFAPPBL1A

CFAPPBL2A

PG16 Gland

(customer supplied)

1 - CAUTION LABEL

1 - LASER WARNING LABEL

Page 1 of 8

Angled Patch Panel

(CFAPPBL1A shown)

FMT1A FMT2A

(sold separately)

ASSEMBLY VIEW showing Fiber Adapter Panels (FAPs) - sold separately

CAUTION:

Fiber optic cable is sensitive to excessive pulling, bending and crushing forces. Consult the manufacturer’s cable specification sheet for

the specific cable in use.

Follow TIA/EIA-568A, 569, 606, and 607 installation guidelines where applicable.

Care should be taken when opening and closing fully loaded drawer in order to protect fiber components.

WARNING: UNMATED CONNECTORS MAY EMIT INVISIBLE LASER RADIATION. DO NOT LOOK DIRECTLY INTO THE END OF THE

CONNECTOR. DO NOT INSPECT WITH MAGNIFYING DEVICES. MAINTAIN CAP ON UNMATED CONNECTORS.

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Determine where the cable will enter the

enclosure. Carefully remove the knock-out so as

not to damage the surrounding sheet metal.

DO NOT install the grommet at this stage.

Grommet will be installed after the enclosure is

mounted to the rack.

To remove the cover, unscrew the #10-32 screw,

slide the cover back, lift up and off.

Preparation and Rack Mounting

Figure 3

#10-32 hex nuts and

#10 flat washers

#10-32 screw

Attach the angled patch panel to the enclsoure

with (2) #10 flat washers and (2) #10-32 hex nuts.

Page 2 of 8

Figure 2

Figure 1

Cover

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

(2) #12-24 x 1/2" screws

Repeat for other side.

Figure 4B

Angled Patch

Panel

(CFAPPBL1A shown)

Figure 4C

Angled patch panels may be mounted directly

to the rack without an enclosure. Place at the

desired position on the rack and secure with

(4) #12-24 x 1/2" screws.

Use (4) M6 x 1 screws if mounting to a metric

rack.

Page 3 of 8

Mount the enclosure to the rack using

(4) #12-24 x 1/2" screws.

Use (4) M6 x 1 screws if mounting to a metric

rack.

Mounting Brackets

Figure 4A

Place the mounting brackets at the desired

position on the rack.

Product specificaties

Merk:	Panduit
Categorie:	Niet gecategoriseerd
Model:	FMT1A
Kleur van het product:	Zwart
Breedte:	482.7 mm
Diepte:	282.9 mm
Hoogte:	43.7 mm
Duurzaamheidscertificaten:	RoHS