Panasonic WV-SPW532L Handleiding

Panasonic Bewakingscamera WV-SPW532L

Lees hieronder de 📖 handleiding in het Nederlandse voor Panasonic WV-SPW532L (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

Included Installation Instructions

PoE device (hub)

Adjustment monitor

Ethernet cable

(category 5e or better, straight)

PGQX1993VA sL0915-4109 Printed in China

IMPORTANT:

●Stretch the tape to approx. twice its length (see the

illustration) and wind it around the cable. Insufficient

tape stretch causes insufficient waterproofing.

●To prevent the Ethernet cable hook from coming

loose easily, fit the LAN connector cover (

B: accessory)

onto the pigtail cable as illustrated, and then slide it in

the direction indicated by the arrow. The connector of

the Ethernet cable used with this camera must meet

the following restrictions.

Height when inserted (From bottom to hook.):

Max. 16 mm {5/8 inches}

Connector width: Max. 14 mm {9/16 inches}

●To install this product outdoors, be sure to waterproof

the cables. Waterproof grade (IEC IP66 or equiva-

lent) is applied to this product only when it is installed

correctly as described in these operating instructions

and appropriate waterproof treatment is applied. The

camera mount bracket and camera arm are not

waterproof.

●:

Installation Guide

Network Camera

Model No.

WV-SPW532L / WV-SPW312L

● This manual describes the installation procedures, network camera installation, cable

connections, and eld-of-view adjustment.

● Before reading this manual, be sure to read the Important Information.

● This manual describes how to install the network camera using model WV-SPW532L as

an example.

Parts and functions

The component names of the camera are as follows. Refer to the illustration when

installing or adjusting the camera.

Standard accessories Making connections

Important Information 1 pc. ...............................

Warranty card 1 set ...........................................

Code label*2 .............................................. 1 pc.

Installation Guide (this document) 1 set ............

CD-ROM*1 ................................................. 1 pc.

The CD-ROM contains the operating instructions and different kinds of tool software programs.

*2 This label may be required for network management. The network administrator shall retain

the code label.

A Template ......................................... 1 Sheet

B LAN connector cover 1 pc. ...........................

C Safety wire 1 pc. ...........................................

D Wire lug fixing screw

M3 × 10 mm {3/8 inches} 2 pcs. ...................

(of them, 1 for spare)

E Safety wire lug 1 pc. .....................................

F Auxiliary handle .................................... 1 pc.

G Desiccant 1 Sheet .........................................

H Waterproof tape 1 pc. ...................................

Turn off each system’s power supply before making a connection. Before making connections,

prepare the required peripheral devices and cables.

IMPORTANT:

●Use all 4 pairs (8 pins) of the Ethernet cable (category 5e or better, straight).

●The maximum cable length is 100 m {328 feet}.

●Make sure that the PoE device in use is compliant with IEEE802.3af standard.

●When the Ethernet cable is disconnected once, reconnect the cable after around 2

seconds. When the cable is quickly reconnected, the power may not be supplied

from the PoE device.

●When cables are used outdoors, there is a chance that they may be affected by light-

ning. In this case, install a lightning arrester just before where the Ethernet cable

connects to the camera.

Connect an Ethernet cable (category 5e or better, straight)

Waterproof treatment for the cable joint sections

Adequate waterproof treatment is required for the cables when installing the camera with

cables exposed or installing it under the eaves.

The camera body is waterproof, but

the cable ends are not waterproof.

Be sure to use the supplied

waterproof tape at the points where

the cables are connected to apply

waterproof treatment in the following

procedure.

Failure to observe this or use of

a tape other than the provided

waterproof tape (such as a vinyl tape)

may cause water leakage resulting in malfunction.

When connecting to a network using a PoE hub

Before starting the installation, check the entire system conguration.

The following illustration gives a wiring example of how to connect the camera to the network via

a PoE device (hub).

Stretch the tape to

approx. twice its length.

2×

IMPORTANT:

● The adjustment monitor is used to adjust the field of view when installing or servicing

the camera. It is not provided for recording/monitoring use.

● Depending on the adjustment monitor, some characters (camera title, preset ID, etc.)

may not be displayed on the screen.

●Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.

The hook engages

with the connector

terminal

LAN connector cover

(B: accessory)

*1 SDXC/SDHC/SD memory card is described as SD memory card.

*2 Depending on the scanning application used, the Data Matrix may not be

able to be read correctly. In this case, access the site by directly entering the

following URL.

http://security.panasonic.com/pss/security/support/qr_sp_select.html

Ethernet cable (category 5e or better, straight)

Use an Ethernet cable (category 5e or better, cross) when directly connecting the camera to a PC.

For U.S. and Canada:

Panasonic i-PRO Sensing Solutions

Corporation of America

800 Gessner Rd, Suite 700 Houston, TX 77024

https://www.security.us.panasonic.com/

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada

1-877-495-0580

https://www.panasonic.com/ca/

For Europe and other countries:

Panasonic Corporation

http://www.panasonic.com

Panasonic i-PRO Sensing Solutions Co., Ltd.

Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

The following parts are used during installation procedures.

RJ45 (female)

Network cable

Ethernet cable

(category 5e or better,

straight)

Wind the tape in a

half-overlapping manner.

Waterproof tape

( : accessory)H

WV-SPW532L

TELE

WIDE

Auto focus (AF)

button

Two-dimensional

matrix barcode

(Data Matrix):

To our website*2

●When the camera is able to communicate with the Lights orange

connected device

LINK indicator

●When data is being sent via the network camera Blinks green (accessing)

ACT indicator

●When AF (Auto Focus) operation is being executed

Blinks red (about once per second)

●When the camera is being started Lights red

●When an SD memory card

is recognized normally

Lights red → Lights off

● When the SD memory card slot is not used or an abnormality Lights red → Stays red

is detected in SD memory card after the camera has started

SD ERROR/AF indicator

● When an SD memory card is inserted and could Lights off → Blinks green →

be recognized Lights off

● When data can be saved after the SD memory card is inserted Lights off → Lights green

and the SD ON/OFF button is pressed (for less than 1 second)

●When data can be saved to the SD memory card Lights green

●When the SD memory card is removed after holding down

Lights green → Blinks green →

the SD ON/OFF button for about 2 seconds Lights off (recording)

Lights green →

Lights off (waiting for recording)

●When data cannot be saved to the SD memory card because Lights off

an abnormality was detected or the SD memory card is

configured not to be used

SD MOUNT indicator

● How to initialize the camera

Follow the steps below to initialize the network camera.

1 Turn o the power of the camera. When using a PoE hub, disconnect the Ethernet cable from the

camera.

Turn on the power of the camera while holding down the INITIAL SET button, and keep the INITIAL

SET button held down till the SD MOUNT indicator is lit in green (more than 10 seconds). In about

2 minutes after releasing the INITIAL SET button, the camera will start up and the settings including

the network settings will be initialized.

● When the INITIAL SET button (i.e. the initializing button) is pressed (less than 1 second) to switch

the output signal of the MONITOR OUT terminal (NTSC



PAL output), the MONITOR OUT terminal

can be switched for the NTSC monitor/PAL monitor.

IMPORTANT:

●When the camera is initialized, the settings including the network settings will be initialized.

Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.

●Before initializing the settings, it is recommended to write down the settings in advance.

●Do not turn off the power of the camera during the process of initialization. Otherwise, it

may fail to initialize and may cause malfunction.

INITIAL SET button (Initializing / NTSCPAL switch button)

1 When the SD ON/OFF button is pressed for less than 1 second, the SD MOUNT indicator is lit

green and data can be saved to the SD memory card.

2 When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT indicator goes

out, and the SD memory card can be removed.

SD ON/OFF button

TILT lock screw

Camera

Front cover

Safety wire ( : accessory)C

Sunshield

Camera mount

bracket

Camera Arm

PAN lock screw

[2] Remove the front cover

Installation

Step 1 Before starting the installation

The installation tasks

are explained using

5 steps.

Tear off the blue tape attached on camera arm before installing the camera.

Prepare the required parts for installation method before starting the installation. The

following is the requirements for the installation method.

Installation method Recommended

screw

Minimum pull-

out strength

Directly mount the camera onto the ceiling or

wall (when there is a space for wiring in the

ceiling or the wall)

M4 screws × 3

724 N {163 lbf}

(per 1 pc.)*1

*1 To mount the camera onto the ceiling or wall, the safety wire ( : accessory)C

must be attached. Have an M6 bolt and nut or anchor (with the minimum pull-

out strength of 724 N {163 lbf}) ready for securing the safety wire.

Step 1

Before starting the

installation

Step 2

Preparation

Step 3

Fixing the camera

Step 4

Adjusting the camera

Step 5

Congure the network

settings

IMPORTANT:

●For the screws or anchor bolts used in the above method, be sure to secure the mini-

mum pull-out strength of 724 N {163 lbf} per screw or bolt.

●Select screws according to the material of the ceiling or wall that the camera will be

mounted to. In this case, wood screws and nails should not be used.

●If a ceiling or wall board such as plaster board is too weak to support the total weight,

the area shall be sufficiently reinforced.

● Because the front cover is temporarily removed when installing or adjusting the camera,

make sure no liquid enters the camera at these times.

Loosen the 4 front cover fixing screws, and then remove the front cover.

Pass the safety wire (

: accessory)

through the wire mounting hole in

the safety wire lug (E

accessory).

Wire mounting hole Front cover fixing screws

Front cover

[1] Attaching the safety wire

Step 2 Preparation

Safety wire lug

: accessory)

Safety wire

(C: accessory) Wire fitting

Wire lug fixing screw

(D: accessory)

Safety wire lug

(E: accessory)

2 Fit the Safety wire lug to the camera.

Recommended tightening torque:

0.59 N·m {0.44 lbf·ft}

* The safety wire is not shown in the

subsequent illustrations.

YAW lock screw

Name plate

Zoom knob

MONITOR OUT jack

(Video Out terminal

Default:

For NTSC monitor)

SD memory card slot

IR LED

Note:

● Any of the PAN, TILT and YAW lock screw can be adjusted by loosening them about

1 turn. Do not unscrew them more than necessary.

● Make sure the camera is supported by hand when loosening screws and adjusting the

direction of the camera.

● When the camera is mounted on the wall, adjust the camera direction by turning the PAN,

TILT and YAW parts as shown in the illustration below.

●The range of angles that the camera portion can actually be turned to in regards to a wall

or ceiling is as follows.

Wall mounting Ceiling mounting

Angle AngleAdjustment part Adjustment part

Horizontal ±90 ° TILT rotation

part*

±180 ° PAN rotation

part

Vertical ±90 ° TILT rotation

part*

0 ° to 90 ° TILT rotation

part

Yaw from -190 ° to

+100 °

YAW rotation

part

from -190 ° to

+100 °

YAW rotation

part

* You can change between horizontal and vertical angles by adjusting the PAN

rotation part.

IMPORTANT:

●Avoid touching the tilting part near the warning

label when you change the tilting angle to secure

the camera.

●If the TILT or PAN lock screw is loosened, the

camera may not be held in place when it is

secured to the wall or ceiling. If this is the case,

temporarily tighten the appropriate lock screws to

keep the camera from moving.

IMPORTANT:

●Each M6 bolt and nut or anchor (locally procured) for securing the safety wire

(C: accessory) must have the minimum pull-out strength of 724 N {163 lbf}.

●Be sure to secure the safety wire (C: accessory) to the foundation of a structure or

an area that is strong enough.

●Be sure to install the camera at least 2 m 80 cm {9.2 feet} from the floor (the dis-

tance between the lowest part of the installed camera and the floor).

●Attach the safety wire (C: accessory) so that if the camera were to become

detached, it would not fall on nearby people.

IMPORTANT:

● After adjustment, be sure to tighten the PAN, TILT and YAW lock screws.

E) As shown in the upper figure, insert the Auxiliary handle ( : accessory) into the wF

zoom knob and loosen the knob by rotating it to the left, and move it between TELE

and WIDE to obtain the desired field of view. Then, lock the zoom knob by rotating it

back to the right. Adjust the focus by pressing the auto focus (AF) button.

F) Adjust the camera angle and field of view by repeating steps A) through E). When

the desired angle and field of view are achieved, tighten the PAN lock screw,

TILT lock screw and YAW lock screw.

Recommended tightening torque

PAN lock screw: 2.7 N·m {2.0 lbf·ft}

TILT lock screw: 4.3 N·m {3.2 lbf·ft}

YAW lock screw: 2.7 N·m {2.0 lbf·ft}

Step

4 Adjusting the camera , , 123

1 Turn on the camera.

Insert an SD memory card into the SD memory card slot, if necessary.

Insert the SD memory card with its label

facing the lens.

●To remove the SD memory card, hold down

the SD ON/OFF button for about 2 seconds.

When the blinking SD MOUNT indicator

goes out, you can remove the SD memory

card.

●After the SD memory card has been

replaced, press the SD ON/OFF button (for

less than 1 second), and make sure the SD

MOUNT indicator is continually lit.

●If you do not press the SD ON/OFF button

after replacing the SD memory card, the SD

MOUNT indicator is automatically lit approx-

imately 5 minutes later.

3 Adjust the camera field of view.

Adjust the direction of the camera with

the PAN, TILT and YAW rotation parts,

and turn the zoom knob until the desired field of view is achieved.

A) Using a 5 mm {3/16 inches} hex wrench (locally procured), loosen the PAN lock

screw on the base of camera arm. To direct the camera to the left, turn the camera

arm part clockwise when viewed from the front. To direct the camera to the right,

turn it counterclockwise. (Panning range: ±180 °)

B) Using a 3 mm {1/8 inches} hex wrench (locally procured), loosen the TILT lock

screw in the middle of camera arm and roughly adjust the direction of the camera.

(Tilting range: 0 ° to 90 °)

C) Temporarily tighten PAN lock screw and TILT lock screw to prevent the camera

from moving.

D) Using a 5 mm {3/16 inches} hex wrench (locally procured), loosen the YAW lock

screw, turn the camera until the sunshield faces up and adjust the tilt of the camera.

(Yawing range: -190 ° to +100 °)

■

When the camera is installed to the ceiling

●Attach the template ( : accessory) to the A

ceiling with the FRONT mark of template

towards the same direction which the camera

is facing.

●Drill holes for securing the camera and wiring

as shown in the illustration to the right.

■

When the camera is mounted on the wall

●Attach template ( : accessory) onto the A

installation wall with the TOP mark facing

upward.

●Drill holes for securing the camera and wiring

as shown in the illustration to the upper right.

●When the side cable is installed, the Ethernet

cable can come out from the direction towards

the ceiling.

* After drilling holes at the ceiling or wall, remove

the template.

●Turn off each system’s power supply before making a connection. Before making

connections, prepare the required peripheral devices and cables.

●Connect the Ethernet cable coming from the camera and coming through the ceiling or

wall according to the instructions in “Making connections”. Waterproof the connections

according to the instructions in “Waterproof treatment for the cable joint sections”.

The following example describes the case when the camera is mounted on the wall.

Attach the camera body by following steps 1～4.

* In the following illustrations, the safety wire is omitted.

* Do not adjust the PAN

rotation part more than

±180 °. This may cause

cables to be wrenched.

Loosen the TILT lock screw by about

1 turn until the camera faces down-

ward and then temporarily tighten the

TILT lock screw.

Change the direction the camera is

facing from directly down to facing up

and temporarily fix the camera in

place.

Fit a pin cable (locally procured) to the

MONITOR OUT jack on the camera

and connect an adjustment monitor.

3 The camera faces upward and then

temporarily tighten the PAN lock screw.

After this, use the lower M4 screw

(locally procured) to secure the camera.

●M4 × 3 screws, Minimum pull-out

strength: 724 N {163 lbf} (per 1 pc.).

After fixing the camera, set the camera

back to downward as described in .2

Use the 2 upper M4 screws (locally

procured) to secure the camera.

And then loosen the PAN lock

screw about 1 turn.

Step 3 Fixing the camera

[1]

Paste the template (A: accessory) on the installation position, and

drill a securing and wiring hole

[2]

Connect the camera with an Ethernet cable

[3]

Fixing the camera

[4]

Connect the adjustment monitor to the camera

ഴ౛/TEMPLATE

TOP

FRONT

्ܰ

Outline

PAN rotation part

YAW rotation part

TILT rotation part

Camera arm part

YAW lock

screw

PAN lock screw

TILT lock screw

Cable access hole

Side cable

access hole

FRONT

direction

TOP

direction

Template

( :A accessory)

Side cable

access hole

Step 4 Adjusting the camera (continued)

4 After adjusting the focus by pressing the AF button, remove the adjustment

monitor.

7 Remove the protection sheet on the front cover.

5 

Stick the desiccant ( : accessory) to the bottom sides inside the front cover and G

mount the front cover.

●Peel off the backing paper of the double-sided tape from the desiccant.

●As shown in the illustration below, stick the desiccant onto the bottom of the lens cover, and

then mount the front cover to the camera with the 4 fixing screws as soon as possible (with-

in 5 minutes).

* Fasten the front cover fixing screws along the diagonal direction.

6 Secure the safety wire ( : accessory) to the ceiling or wall.C

■ When the camera is installed to the ceiling

IMPORTANT:

●Once the front cover is installed, the camera may be slightly out of focus. After

installing the front cover, use the auto focus via the settings menu.

Note:

●When sticking the desiccant, make sure it will not spill over the front cover.

●Do not let the desiccant (G: accessory) get damp, nor touch it with wet hands.

● While adjusting the lens, do not let water drops drip into the lens cover or the camera.

●Do not stick the desiccant (G: accessory) until you have finished adjusting the field of view

and the camera focus. Do not unpack the desiccant too early; otherwise its performance

may be affected.

●Desiccant should be replaced after about 3 years. The effective period may be shortened

according to environment. Besides, when removing the front cover to adjust the camera

or process other operations, replace the desiccant with a new one.

Model No. of replacement part Desiccant 3CJ001261AAA

When the camera has been installed, remove the protection sheet from the front

cover. After removal, be sure not to touch the clear part of the front cover.

Note:

●When removing the camera, perform removal by following the installation proce-

dure in the reverse order.

Step 5 Configure the network settings

M6 bolt and nut

or anchor (locally

procured)

Safety wire

(C: accessory)

Ceiling

■ When the camera is mounted on the wall

Safety wire

(C: accessory)

M6 bolt and nut

or anchor (locally

procured)

Wall

Camera mount

bracket

M4 × 2

(locally procured)

M4 × 3

∅25 mm {1"}

M4 (locally

procured)

MONITOR OUT jack

(Video Out terminal

Default:

For NTSC monitor)

PAN lock screw

TILT lock screw

Front cover

Front cover fixing

screws × 4

Desiccant (G: accessory)

Ceiling

The following are descriptions for when the camera with default settings is configured. If you are using fire-

wall software on your PC, the Setup Program may not be able to find any cameras on your network.

Configure the setting of the camera after temporarily invalidating the firewall software. Contact the network

administrator or your Internet service provider for information about configuring the settings of the network.

q Insert the provided CD-ROM into the CD-ROM drive of your PC.

w Click the [Run] button next to [IP Setting Software].

[Panasonic IP Setting] screen will be displayed. When a camera is found, information

about it, such as its MAC address and IP address, is displayed.

e Select the camera you want to congure, and click [Access Camera].

Note:

●Refer to “Using the CD-ROM” in the operating instructions on the provided

CD-ROM for further information about CDLauncher.

Note:

● When no image is displayed on the “Live” page, refer to the Troubleshooting in

the operating instructions on the provided CD-ROM.

●It is possible to enhance the network security by encrypting the access to camer-

as using the HTTPS function. Refer to the operating instructions on the provided

CD-ROM for how to configure the HTTPS settings.

●Click the [Setup] button on the “Live” page, the user authentication window will be

displayed. Enter the default user name and password as follows, and log in.

User name: admin

Password: 12345

●When changing settings related to the network settings, such as connection

mode, IP address, and subnet mask, click the [Network Settings] button in

[Panasonic IP Setting] screen as shown in step

e, then change each setting.

●Due to security enhancements in “IP Setting Software”, “Network settings” of the

camera to be configured cannot be changed when around 20 minutes have

passed after turning on the power of the camera. (When the effective period is set

to “20 min” in the “Easy IP Setup accommodate period”.)

However, settings can be changed after 20 minutes for cameras in the initial set

mode.

●“Network Camera Recorder with Viewer Software Lite” which supports live moni-

toring and recording images from multiple cameras is available. For further infor-

mation, refer to our website

(http://security.panasonic.com/pss/security/support/info.html).

Note:

●When cameras are displayed in [Panasonic IP Setting] screen, click the cam-

era with same MAC address as the MAC address printed on the camera that

you want to configure.

Conguring the camera so that it can be accessed from a PC r If the installation screen of the viewer software “Network Camera View 4S” is displayed,

follow the instructions of the wizard to start the installation. (The viewer software is in-

stalled from the camera.)

● The License Agreement will be displayed. Read the Agreement and choose “I accept

the term in the license agreement”, and click [OK].

●The launcher window will be displayed. If the launcher window is not displayed, double

click the “CDLauncher.exe” le on the CD-ROM.

●The “Live” page will be displayed.

●

If you cannot install the viewer software “Network Camera View 4S” or if images are not

displayed, click the [Install] button next to [Viewer Software] on the launcher window to

install the software.

●Perform the [Time & date] settings in the “Setup” - “Basic” page before using the camera.

IMPORTANT:

●Securely tighten the 4 front cover fixing

screws. Failure to do so may cause the cam-

era to fall or waterproof failure.

Recommended tightening torque: 0.59 N·m

{0.44 lbf·ft}

Warning label

Auto focus

(AF) button Zoom knob

MONITOR OUT jack

SD memory card

(Ensure that the label faces the lens.)

Auxiliary handle

( : accessory)F

TELE

WIDE

Product specificaties

Merk:	Panasonic
Categorie:	Bewakingscamera
Model:	WV-SPW532L
Kleur van het product:	Chroom
Soort:	IP-beveiligingscamera
Internationale veiligheidscode (IP):	IP66
Ondersteunde videoformaten:	H.264
Vormfactor:	Rond
Automatisch scherpstellen:	Ja
Ondersteuning voor plaatsing:	Binnen & buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Montagewijze:	Plafond/muur
Ondersteunde video-modi:	1080p
Maximum resolutie:	2048 x 1536 Pixels
Videocompressieformaten:	H.264
Type stroombron:	Power over Ethernet (PoE)
Minimale belichting:	0.07 Lux
Aantal cameras:	1
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	SD, SDHC, SDXC
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Video bewegings-detectie:	Ja
Brandpuntbereik:	2.8 - 10 mm
Volledige HD:	Ja
Omvang optische sensor:	1/3 "
Type beeldsensor:	MOS
Optische zoom:	3.6 x
Ondersteunde grafische resoluties:	1920 x 1080 (HD 1080), 2048 x 1536 (QXGA)
Ruisonderdrukking:	Ja
Ondersteunde beveiligingsalgoritmen:	SSL/TLS
Veiligheidsfunties:	Dust resistant, Water resistant
Maximaal 30 frames per seconde:	30 fps
Power over Ethernet (PoE):	Ja
Pan bereik:	-90 - 90 °
Dag/nacht modus:	Ja
Maximum aperture number:	1.6
Weerbestendig:	Ja
Bereik kantelhoek:	-90 - 90 °