PAC WRI-P Handleiding
PAC
Niet gecategoriseerd
WRI-P
Bekijk gratis de handleiding van PAC WRI-P (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 24 mensen en kreeg gemiddeld 4.4 sterren uit 12.5 reviews. Heb je een vraag over PAC WRI-P of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/2
1
11-17-09
WRI-P
Wired Remote Input Control Interface
Before You Start
A. Prepare for the installation.
• If possible, install the WRI-P while you are installing the new head unit.
• Plan a general installation location for both the WRI-P infrared eye and the control body.
• If you are installing the WRI-P in conjunction with a SWI-PS, please refer to the SWI-PS instructions for all wiring
and programming information.
Pacific Accessory Corporation
IP-BUS input
Antenna jack
Power
To Infrared Eye
Fuse Jack for the SWI-PS
IP-BUS cable
Installation Instructions
Compatible with Pioneer in-dash
navigation units that lack an IR receiver
but have a wired remote input.
Wiring Connections
Step 1.
Connect the BLACK
wire to ground (-).
Verication: Wire
or location registers
a constant (-) when
probed.
Step 2.
Connect the RED wire
to switched +12V.
Verication: Wire reg-
isters +12V when the
ignition key is turned
to the ACC or ON posi-
tions.
Black
Red
Black
Red 12V+ (Switched)
2
Step 3.
Connect the 3.5mm stereo plug on 5 pin Molex to the wired remote input on
the back of the radio..
Black
Red 12V+ (Switched)
Back of Radio
Wired Remote In
Step 4
Mount the infrared eye in a suitable location
Compatibility Notes
1. The voice recognition command via wireless remote is not supported on the following models: AVIC-F700BT, AVIC-F900BT,
AVIC-U310BT, AVIC-X710BT, and AVIC-X910BT.
2. PAC recommends the use of the Pioneer CD-R510 or CXC9115 remote for maximum compatibility with the WRI-P. Other
Pioneer remotes may work, but some functions / buttons may not be supported.
Step 5
If applicable, install the SWI-PS and connect
the 3.5mm plug to the SWI-PS input on the
side of the WRI-P
WRI-P Functions
CD-R510 Function
VOLUME + Volume up
VOLUME - Volume down
BAND Band
SRC Source
ATT Mute/Attenuate
PGM Phone Status
OFF/H Answer Call
ON/H End Call
Joystick Function
UP Preset +
DOWN Preset -
RIGHT Seek >>
LEFT Seek <<
Center Voice Activation
Note: CLEAR
button is for self
testing of WRI-P.
Black
Red 12V+ (Switched)
To Suitable
Location
Troubleshooting
The WRI-P has a self test mode which can determine if it is sending and receiving the proper signals. Follow the steps below to
engage the self test mode:
1. Connect the module to a 12v source (do not apply power yet).
2. Connect the 3.5mm output plug on 5 pin Molex to the 3.5mm input on the side of the module.
3. Connect the IR receiver to the WRI-P.
4. Power up the WRI-P
5. Using the CD-R510 remote, point the remote at the IR receiver and press the CLEAR button on the remote to start the test.
The LED will blink 9 times while testing the analog outputs and inputs then pause for a second. It will blink 3 times to conrm it
passed the test.
See
troubleshooting
section below
Pacic Accessory Corporation - Santa Ana, CA 92705
866-931-8021• www.pac-audio.com
Product specificaties
| Merk: | PAC |
| Categorie: | Niet gecategoriseerd |
| Model: | WRI-P |
Heb je hulp nodig?
Als je hulp nodig hebt met PAC WRI-P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd PAC
2 Mei 2025
10 Maart 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
19 Februari 2025
11 Februari 2025
Handleiding Niet gecategoriseerd
- MaedHawk
- Tempmate
- AirTurn
- Zagg
- Excalibur
- Mattel
- Dangerous Music
- T.akustik
- SIG Sauer
- OBH Nordica
- Ledlenser
- Earbreeze
- Ravanson
- IP-COM
- Karlik
Nieuwste handleidingen voor Niet gecategoriseerd
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025