PAC BCI-CH21 Handleiding

Bekijk gratis de handleiding van PAC BCI-CH21 (6 pagina’s), behorend tot de categorie Dashcam. Deze gids werd als nuttig beoordeeld door 12 mensen en kreeg gemiddeld 4.2 sterren uit 8 reviews. Heb je een vraag over PAC BCI-CH21 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

PAC

®

| Ph. 866-931-8021 | [email protected]

©2016 Pacic Accessory Corporation

www.pac-audio.com

Rev. 090916

Page 1

Reverse Camera Input and Navigation Unlock

Interface for Chrysler / Dodge / Jeep Vehicles

Pacific Accessory Corporation

BCI-CH21

J1850

Class 2

VPW

Class 2

J1850

100011101111001001101100

111010000110110111001100

Arbitration

EOD

CRC

100011101111001001101100

111010000110110111001100

Class 2

Class 2

J1850

The BCI-CH21 will program your Chrysler / Dodge / Jeep radio to allow the addition of a reverse camera input if the

vehicle is not equipped with one from the factory (reverse camera sold separately). The BCI-CH21 will allow the factory

navigation features of your radio to be used by the passenger at anytime. The interface also offers extra features such

as: adding Blind Spot Cameras, Front Camera, VES activation & Audio/Video input capabilities.

Introduction & Features

Important Notes

1. It is very important to follow the exact sequence of installation steps as listed below. Failure to do so will result in the interface not

working as intended.

2. If you change the dipswitch settings, you must disconnect and reconnect power for the change to take effect

3. To activate the Blind Spot Camera input, a VS41 (sold separately) must be connected.

4. To activate the Front Camera input, a VS41 (sold separately) must be connected in addition to turning on DIP switch 4

5. The navigation unlock feature must be activated every time the key is cycled.

6. The AVS21 A/V switcher must be used in order to use more than one video source with the BCI-CH21.

7. If the vehicle is equipped with an external VES Player, the RCAs labeled “Audio/Video To Head Unit” will not allow an additional input

to the head unit. You must use the factory A/V aux in located in the rear of the vehicle.

8. If the vehicle’s reverse lights come on when the reverse camera feature is engaged the diode is not wired properly. Please refer to “Fig.

C” on page two for proper diode wiring.

9. If the factory radio does not come on or “ickers” off & on, the factory amplier does not turn on or you are receiving audio on only one

side of the vehicle, please make sure that the male pins in the BCI-CH21 plug are not bent or out of place.

10. In order to see the text generated by the BCI-CH21 on the multi-function display (MFD), it must be set to display audio text.

1. Turn on the DIP switches that correspond with the features you want to add.

These dipswitches must be set to the proper conguration before connecting the

interface to the vehicle.

2. Depending on the vehicle you are installing the BCI-CH21 into, you may need to

cut the white/red loop in the harness. Please refer to the chart to the right to see if

you need to cut the loop. If your vehicle is listed, cut the loop. If not, do not cut the

loop. Please see the Troubleshooting section on page 4 for further explanation of

the loop and its purpose.

3. If the vehicle is not equipped with an MFD or external Uconnect module mount

the LED in a location that is visible to the driver. In vehicles equipped with a Multi-

Function Display (MFD) in the instrument cluster or an external Uconnect module

it is not necessary to connect and mount the LED. The best way to determine if

the UConnect is external is if the vehicle has an external iPod or USB input (not

including the one built into the front of the radio).

4. Remove the factory radio and disconnect the factory harness(es).

5. Connect the BCI-CH21 harness to the back of the factory radio.

6. If adding reverse camera or additional A/V inputs, connect the BCI-CH21-AUX

Harness to the back of the factory radio.

7. Connect the aftermarket reverse camera’s video output to the female yellow RCA

located on the radio side of the BCI-CH21-AUX harness. Use the BCI-CH21’s

red camera turn on wire to power the aftermarket reverse camera. If you are only

using the BCI-CH21 as a navigation unlock, this step is not necessary.

Installation Steps

MakeModelYear

Chrysler2002011‐2014

Chrysler3002008‐2010

ChryslerSebring2008‐2010

DodgeAvenger2008‐2013

DodgeCaliber2010‐2012

DodgeChallenger2008‐2014

DodgeCharger2008‐2010

DodgeDakota2008‐2010

DodgeDurango2008‐2009

JeepCommander2008‐2010

JeepCompass2009‐2013

JeepGrandCherokee2008‐2010

JeepLiberty2008‐2013

JeepPatriot2008‐2015

CutRed/WhiteLoopinTheseVehicles

DIP

1234

ON

Aftermarket Reverse CameraNavigation UnlockVESFront Camera

1234

Set DIP switches to the ON position to activate the corresponding features.

Set DIP switches to the OFF position for any features that are not desired.

Product specificaties