Ozito PXCHTK-218 Handleiding

Ozito Heggenschaar PXCHTK-218

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXCHTK-218 (6 pagina's) in de categorie Heggenschaar. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
CORDLESS HEDGE
TRIMMER KIT
INSTRUCTION MANUAL
SPECIFICATIONS
Voltage: 18V
Battery: 2.0Ah Li-ion
Charge Time: 2.5Hrs
No Load Speed: 2,200/min
Max. Cutting Capacity: 11mm
Blade Length: 460mm
Weight: 2.45kg
PXCHTK-218
WHAT’S IN THE BOX
Cordless Hedge Trimmer
2.0Ah Battery & Eco Charger
ozito.com.au
Blade Cover
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE
WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING
YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER
SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer service helpline
above.
0316
WARNING
The following actions will result in the warranty being
void.
‱ If the tool has been operated on a supply voltage other
than that specied on the tool.
‱ If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
‱ Failure to perform maintenance as set out within the instruction manual.
‱ If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty. Warranty excludes consumable parts, for example: blade, blade cover.
ONLINE MANUAL
Scan this QR Code with your mobile
device to take you to the online manual.
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
The blade cover protects the blade
when not in use. Simply slide it
off the blade before use. Once
nished operating, place the cover
back over the blade.
Ensure the safety guard
is tted securely onto the
hedge trimmer before use.
Tighten the screws on either
side if necessary.
Blade Cover
Safety Guard
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND BATTERY DISCONNECTED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
WARNING! NEVER USE THE HEDGE TRIMMING
UNLESS THE SAFETY GUARD IS FITTED.
WARNING! NEVER START THE HEDGE TRIMMER
WHILE THE BLADE COVER IS FITTED.
9. Battery Release Tab
10. Battery Charge LED’s
11. Battery Charge Indicator Button
12. Blade Cover
13. Charger
14. Charger LED
ACCESSORIES
1
9
2
10
3 4 5 6
11
7
12
8
13 14
1. Impact Guard
2. Blade
3. Safety Guard
4. Front Handle
5. Safety Switch
6. On/Off Trigger
7. Rear Handle
8. Battery Seating
CORDLESS HEDGE TRIMMER
WARNING! WHEN HANDLING THE BLADE ASSEMBLY,
WEAR NON-SLIP, HEAVY-DUTY PROTECTIVE GLOVES.
DO NOT PLACE YOUR HAND OR FINGERS BETWEEN
BLADES OR IN ANY POSITION WHERE THEY COULD
GET PINCHED OR CUT. NEVER TOUCH BLADES
OR SERVICE THE UNIT WITH THE BATTERY PACK
INSTALLED.
2. BATTERY & CHARGING
Charging your lithium ion battery - Eco Charger
The tools battery has been shipped in a low charge condition, and requires charging
prior to use. Allow several cycles of charging and discharging (through use of the tool)
for the battery to reach its optimum performance / runtime.
CAUTION! IF THE BATTERY IS TOO HOT OR TOO
COLD WHEN INSERTED INTO THE CHARGER,
THE LED WILL FLASH RED AND GREEN. REMOVE
BATTERY FROM CHARGER AND STORE AT ROOM
TEMPERATURE 20 C BEFORE CHARGING.Âș
CAUTION: THE CHARGER FOR THIS PRODUCT
SHOULD BE PROTECTED BY A RESIDUAL CURRENT
DEVICE (RATED AT 30MA OR LESS).
1. Connect the charger into a mains power outlet.
4. The charger LED will illuminate red signifying that the battery is charging.
5. When removing the charger from
the battery, rst press the battery
release tab, then slide the charger
from its position.
Note: The battery will not develop a memory, it does not have to be fully
discharged before recharging
2. The charger LED will ash green
showing power is being supplied
to the charger.
3. With the battery sitting on a at
surface, align the raised ribs on
the battery with the recess in the
charger and slide onto the battery
ensuring a rm connection.
Battery Charge Indicator
The purchased battery is equipped with a
battery charge indicator to show the state of
the battery charge.
Press the charge indicator button and look to
see which LED lights.
Battery requires immediate charging
Low state of charge, requires charging soon.
Mid state of charge
Full state of charge.
Note: The battery needs to be removed from the tool to check the state of charge.
Battery protection system
The tool is equipped with the battery protection system, which helps to ensure a long
service life.
The output power automatically cuts off during operation when the tool and/or battery
are placed under the following situations:
‱ When the tool is overloaded:
If this occurs, release the trigger switch and remove causes of overload, then pull
the switch trigger again to restart.
‱ When the remaining battery capacity becomes low:
Recharge the battery pack.
Note: The battery protection system does not in any way damage the tool.
Note: The indicated capacity may be lower than the actual level during use or
immediately after using the tool.
Charger LED Indicator
LED Indicator Situation
GREEN (Flashing) Stand By (no battery pack is inserted)
RED (Illuminated) Battery is charging (low charge)
GREEN (Illuminated) Battery is fully charged
RED (Flashing) Battery or Charger fault
RED & GREEN (Flashing) Battery pack is too hot or too cold (remove battery from
charger and store at room temperature 20ÂșC. Insert
battery again when at correct charging temperature). If
this happens again, the battery is defective and needs
to be replaced.


Product specificaties

Merk: Ozito
Categorie: Heggenschaar
Model: PXCHTK-218

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXCHTK-218 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Heggenschaar Ozito

Handleiding Heggenschaar

Nieuwste handleidingen voor Heggenschaar