Ozito OSC-018 Handleiding

Ozito Zaagmachine OSC-018

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito OSC-018 (8 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
18V LITHIUM
ION
18V LITHIUM
POWERE D BY
POWERED BY
ION
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase and is intended for DIY (Do It
Yourself) use only. If a product is defective it will
be replaced in accordance with the terms of this warranty. Lithium
Ion batteries are covered by a 12 month warranty. Warranty
excludes consumable parts, for example: guide bar and chain.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specied on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
CORDLESS
CHAINSAW
18V Lithium Ion
INSTRUCTION MANUAL
SPECIFICATIONS
Voltage: 18V
Battery: 1.5Ah Li-ion
Charging time: 3 Hours
Bar length: 254mm (10”)
Chain pitch: 9.53mm (3/8”)
Chain speed: 4.3m/s
Oil tank capacity: 220ml
Weight with battery: 3.3kg
OCS-018
WHAT’S IN THE BOX
WARRANTY
ozito.com.au
1117
18V LITHIU M
Suits: OCS-018
ION
18V LITHIU M
Suits: OCS-018
ION
Chainsaw
Guide Bar Cover
Guide Bar
Chain
Battery Pack
Battery Charger
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
3
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
18V LITHIUM
ION
POWERED BY
18V LITH IUM
Suits: OCS-018
ION
18V LITH IUM
Suits: OCS-018
ION
Fitting the chain and bar
1. Completely unscrew the guide
bar locking knob, in a counter
clockwise direction.
3. Fit the chain over the guide bar,
making sure that the cutters are
facing in the direction of rotation.
1. Battery seating
2. Rear handle
3. Trigger switch
4. Oil level window
5. Side cover
6. Guide bar locking knob
7. Chain
8. Guide bar
9. Bucking spikes
10. Safety chain brake
11. Front handle
12. Chain oil tank cap
13. Motor cover
14. Lock-off button
15. Guide bar cover
16. Battery
17. Battery release tab
18. Battery charger
19. Battery charger cradle
CORDLESS CHAINSAW
ACCESSORIES
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
CAUTION! ALWAYS BE SURE THAT THE TOOL IS
SWITCHED OFF AND THE BATTERY PACK IS REMOVED
BEFORE CARRYING OUT ANY WORK ON THE TOOL.
CAUTION! ALWAYS WEAR GLOVES WHEN HANDLING
THE CHAIN AS IT IS VERY SHARP AND CAN CUT YOU
WHEN IT IS NOT MOVING.
B
2. Remove the guide bar cover.
4. Place the guide bar and chain
in position, ensuring that
the chain is around sprocket
wheel (A). Also ensure that the
chain tension pin (B) ts into
the guide bar. If it does not t,
it can be adjusted slightly with
the chain tensioning
screw. The chain must
not slip off the bar when
you do this.
5. Pull the guide bar forward
until the chain is closely
seated. Make sure that all the drive links are
in the groove of the bar.
A
6. Attach the side cover and secure it with the
side cover lock. Do not fully tighten the side
cover lock until after adjusting the chain
tension.
31 2 4 5 6 7 8
9 10 11 12 13 14
15 16 17 1918
2. OIL
IMPORTANT: IT IS VITAL FOR THE PROPER AND SAFE
OPERATION OF THE CHAINSAW THAT THE CHAIN IS
TENSIONED CORRECTLY.
IMPORTANT: THE CHAIN SHOULD BE ADJUSTED
BEFORE FIRST USE, AGAIN AFTER 2-3 MINUTES OF
OPERATION AND RECHECKED AND ADJUSTED IF
NECESSARY AFTER EACH 30 MINUTES OF USE. TAKE
CARE NOT TO OVER TENSION THE CHAIN.
IMPORTANT: ONLY USE OIL THAT IS EXPRESSLY
LABELLED “CHAIN BAR OIL”.
WARNING!: NEVER START WORK UNLESS THE
CHAIN AND BAR ARE LUBRICATED.
5. To check the lubricating system,
switch on the chainsaw and hold it
with the guide bar and chain above
some light coloured paper such as
newspaper. A steadily increasing
stain caused by oil spray shows the
lubricating system is working.
2. Fill the tank with chain bar oil.
The capacity of the chain oil
tank is 220ml. Do not over ll.
Adjusting the chain tension
1. Loosen the guide bar locking knob
slightly, by rotating it in an anti
clockwise direction.
2. Adjustment chain tension
screw CLOCKWISE to increase
chain tension. Turning screw
COUNTERCLOCKWISE will
decrease amount of tension on
the chain. Adjust the chain tension
screw for the correct tension.
For the correct chain tension, pull up
on the chain from the top and middle
of the exposed guide bar. The bottom
tip of the links should only just stay in
the track.
3mm gap is
the ideal tension
3. After the chain has been accurately
tensioned, lock the guide bar in place with
the side cover lock.
1. Remove the chain oil tank cap
3. Always ll the oil tank when
the oil level is below the
minimum mark on the oil level
window.
4. Ret cap and clean any
oil spillage.
NOTE: Chain bar oil may leak if the tool is left for long periods. This is
normal. If the tool is to be left unused for an extended time, drain the oil
from the tool. Rell before use.
18V LITH
OWER ED BY
POWERE D

Product specificaties

Merk: Ozito
Categorie: Zaagmachine
Model: OSC-018

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito OSC-018 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine Ozito

Ozito

Ozito JSW-6100U Handleiding

9 Juli 2023
Ozito

Ozito RSW-5200 Handleiding

26 Juni 2023
Ozito

Ozito JSW-4000U Handleiding

24 Juni 2023
Ozito

Ozito JSW-8100U Handleiding

20 Juni 2023
Ozito

Ozito RSW-5200U Handleiding

18 Juni 2023
Ozito

Ozito PXJSS-600U Handleiding

16 Juni 2023
Ozito

Ozito SCMS-10STANDU Handleiding

13 Juni 2023
Ozito

Ozito PXCCSS-0182U Handleiding

13 Juni 2023
Ozito

Ozito PXRSS-400U Handleiding

11 Juni 2023
Ozito

Ozito CSW-7000U Handleiding

9 Juni 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Worx

Worx Nitro WX542.9 Handleiding

26 April 2024
Fieldmann

Fieldmann FZP 25410-B Handleiding

15 April 2024
Milwaukee

Milwaukee M18 BJS Handleiding

10 April 2024
Rona

Rona Standard Plus-C Handleiding

10 April 2024
Rona

Rona Profi-C Handleiding

10 April 2024
Milwaukee

Milwaukee SCS 65 Q Handleiding

10 April 2024
Milwaukee

Milwaukee M12 BS Handleiding

10 April 2024
Milwaukee

Milwaukee M18 FMCS66 Handleiding

10 April 2024
Milwaukee

Milwaukee M18 BSX Handleiding

10 April 2024
Bavaria By Einhell

Bavaria By Einhell BFS 800E Handleiding

9 April 2024