OSD Audio ICE800ST Handleiding

OSD Audio Speaker ICE800ST

Lees hieronder de 📖 handleiding in het Nederlandse voor OSD Audio ICE800ST (5 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 59 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5

Owner’s Manual In-Ceiling Speakers

A U D I O

OSD

18AWG minimum - for distances up to ………………………. . 10 ft

16AWG - from ……………………………………………. 10 to 50 ft

14AWG - from …………………………………………… 50 to 100ft

- Where is the best place to install the speakers

- Where do the speakers sound the best?

- Try to separate the speakers 6 - 10 feet apart.

- If you intend to paint the grilles, try to do so before installation.

Q k installation uic guide

- Pencil

- Drill

- Tape Measure

- Wire cutter

- Philips-head screwdriver

- Sandpaper

Tools needed for installation

STEP 4: Mounting Dog Ear

Tighten the dog-ear brackets by simply turning the screws on the

slowly clockwise. The quick-turn mounting system and frame will

"sandwich" or clamp around the wall to hold the speaker securely in

place. (See Diagram 4)

STEP 1: Cutout Tracing

Trace along the inclusive template. Cut along the traced line using a

drywall saw or rotary drill. A simple, inexpensive drywall saw (about

$10 at your local hardware store) is the best choice for beginners.

Caution: This is the most important part of the entire installation.

If you are not certain whether any obstructions exist behind the

desired mounting area, you should start by cutting a small hole in

the center of your penciled mounting hole with a drywall saw. Use a

piece of sandpaper to sand down the cut out edge for a smoother

contour. (See Diagram 1 )

Run the cable into the cut out location while leaving an extra two

feet to make the connection to the speaker easier. Strip back

approximately ½ inch of the speaker cable insulation and twist

the copper wires tightly for easy insertion.

On the back of the speaker, press down on the gold-plated

compression terminal to reveal the "eye" and insert the speaker

cable through the eye for secure connection. Release the compres-

sion terminal to lock each cable securely. ( See Diagram 2)

STEP 3: Tweeter Adjustment

To determine the length and the gauge of speaker wire, you will need to

measure the distance between your receiver/amplifier to the speakers.

- Always buy more than you think you would need.

- Equal wire lengths should always be used to maintain an equal

balance in sound volume.

- Sound quality is lost when using thin wire gauge over a long

distance.

- Utility knife

- Safety eyewear

- Gloves

Speaker wire

- When placing the speakers in the ceiling, try to install them

listening area. (For LCR model only)

Your in-ceiling speakers come from the factory with the tweeter facing

response. However, you can adjust the tweeter to focus e sound at th

your listening location. In order to do this, gently press on the grill (See

Diagram 3). Caution: Do not touch the tweeter dome while adjusting for

your hearing preference. (See Diagram 3) -Pivoting Tweeter Model Only

Diagram 3:

Adjust the tweeter here

Tweeter

STEP 2: Cut Out

Diagram 1:

Diagram 2:

Dog Ear

Diagram 4:

Mounting Dog Ear

Lock

LOSE

Product specificaties

Merk:	OSD Audio
Categorie:	Speaker
Model:	ICE800ST
Kleur van het product:	Grijs
Gewicht:	- g
Breedte:	- mm
Diepte:	177.8 mm
Hoogte:	279.4 mm
Gebruikershandleiding:	Ja
Connectiviteitstechnologie:	Bedraad
Snelstartgids:	Ja
Gemiddeld vermogen:	120 W
Aanbevolen gebruik:	Universeel
Impedantie:	8 Ohm
Geschikt voor buitengebruik:	Ja
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Ceiling-mountable, In-wall/in-ceiling
Aantal drivers:	1
Woofer:	Ja
Frequentiebereik:	45 - 22000 Hz
Gevoeligheid:	89 dB
Versterkeraansluiting (binding post):	Ja
Diameter woofer:	8 "
Aantal woofer drivers:	1
Diameter hogetonenluidspreker:	1 "
Aantal tweeter drivers:	1
Tweeter:	Ja
AirPlay:	Nee
Multi-Room Streaming (MRS)-ondersteuning:	Nee