Optoma 3D-RF Glasses Handleiding

Optoma Projector accessoire 3D-RF Glasses

Lees hieronder de 📖 handleiding in het Nederlandse voor Optoma 3D-RF Glasses (24 pagina's) in de categorie Projector accessoire. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24

User’s Manual – Optoma - System Optoma - Glasses and Optoma -3D RF : 3D RF 3D

RF Emier

Contains Patent Pending soware and technology from Bit Cauldron

Conent les logiels de brevet en instance et la technologie de la compagnie Bit Cauldron

Optoma - Emier Manual 3D RF

The Optoma - Emier connects Optoma 3D-XL converter box to the Optoma -3D RF 3D RF Shuer Glasses

for the ulmate in 3D stereoscopic viewing. This document describes the features, connecon, setup,

and operaon of the Optoma -3D RF Emier with Optoma 3D-XL converter box.

Features

 RF synchronizaon for uninterruptable 3D glasses performance

 Ready to watch compability with 3D Ready Optoma projectors with Optoma 3D-XL converter box

 LED indicators assist with IR Sensor placement

 Management Soware enables Upgrade funconality for compability with future 3D TVs

 Manual performance adjustment capability

Connecons

Optoma 3D-XL converter box with 3D Emier Port

1: Connect the Optoma - emier to the Optoma 3D-XL converter box using the IR Emier Port as 3D RF

shown below.

Basic Features

RF Communicaon of Synchronizaon Signal

RF communicaons enables the Optoma - System to provide an awesome and uninterruptable 3D 3D RF

viewing experience. Line of sight obstrucons, emier placement and viewer seang arrangements

have no impact on the performance of the emier to glasses synchronizaon. Opmal seang distance

and viewing angle is determined by the capabilies of the 3D Ready Projector coupled to the Optoma

3D-XL converter box and - System. 3D RF

LED Indicators

The Optoma - Emier uses 5 mulcolored LEDs 3D RF

to indicate modes of operaon or other informaon.

The LEDs are located on the top of the emitter close

to the joysck and display red, green, or orange.

Joysck

The Optoma -3D RF Emier uses a joysck to allow

the user to enable various modes and change

sengs. The joysck has two axes and a center

buon funcon. Funcon of the axes and buons

are dependent on the operang mode as described

in following secons.

Modes of Operaon

The Optoma - Emier has 5 modes of operaon. 3D RF

 Normal

 Sync Signal Status (Strength)

 Manual Tuning of Glasses Performance

 Pairing the Optoma - Emier with Optoma 3D RF 3D- Glasses RF

 Set Polarity

Accessing Modes

During normal operaon, the joysck is used to

access dierent modes of operaon. Press and

hold the joysck to cycle through the available

modes. Release the joysck to select a mode. In

any mode, the normal mode of operaon

resumes aer 60 seconds of inacvity with the

excepon of Set Polarity mode. Set Polarity mode

will me out in 10 seconds.

Product specificaties

Merk:	Optoma
Categorie:	Projector accessoire
Model:	3D-RF Glasses
Kleur van het product:	Zwart
Gewicht:	57 g
Compatibiliteit:	Optoma HD83, HD33, HD300X, GT750
Afmetingen (B x D x H):	160 x 160 x 55 mm