Nxg NX-W5.2-LCR-P Handleiding

Nxg Speaker NX-W5.2-LCR-P

Lees hieronder de 📖 handleiding in het Nederlandse voor Nxg NX-W5.2-LCR-P (2 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Where To Place Your In-Wall Speakers

Placement can make all the difference in how your speakers sound, and how easy they will be

to install. Carefully consider where your speakers should be positioned. For optimum perform-

ance in a center-channel application, speaker should be mounted directly above or below TV

or monitor. For optimum performance when used in right and left main listening positions,

speakers should be mounted to the left and right of the main listening position and a minimum

of 8 to 10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical

wiring, heating ducts, water pipes, etc. Make sure the wall or ceiling materials are sturdy enough

to support the weight of the speakers.

Note: When the NX-W5.2-LCR-P is mounted horizontally in a center-channel application, modifi-

cation may need to be made to the stud cavity to accommodate speaker.

Pivoting Tweeter (Fig. 3)

The tweeter in the NX-W5.2-LCR-P speaker may be adjusted, allowing you to tailor the speaker

to better fit the listening area. The overall smoothest response is achieved with the tweeter fac-

ing straight out: however, you may find the sound more pleasing by aiming the tweeter toward

a particular listening area. To adjust the tweeter angle, apply pressure on the ring surrounding

the tweeter with your thumb or finger.

Tweeter Level Adjustments (Fig. 4)

The tweeter level control allows you to tailor the speakers’ frequency response to better match

the room’s acoustics. As an example, if a room has a hardwood floor, which makes it acoustical-

ly brighter sounding, you may want to adjust the tweeter level down to compensate. You can

experiment to find the sound that’ most pleasing to you in your particular listening environment. s

Speaker Installation In Existing Construction (See Fig. 5)

Once you have selected the location for your speakers, you are ready to install them.

You will need the following:

• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers

• Pencil • Utility Knife or Drywall Saw • Small Level

• Masking Tape • Phillips Screwdriver • Speaker Wire

NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer

or custom audio contractor.

1. NXG Architectural Speakers are designed to be installed in the wall area between studs.

Using a stud finder, make sure you are between two studs. Using the supplied template and a

level to ensure your template is straight, tape the template to the wall and lightly trace around the

inside with a pencil.

2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of

the outline. This will allow you to check for any obstructions that may exist behind the desired

location. CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in

the planned installation areas prior to drilling or cutting the wall.

3. Run speaker wire from your amplifier or speaker switching device to the speaker location.

4. Remove the grille from the speaker. If you like the standard white finish of your NXG In-Wall

Speakers, skip to step 5, but if if you want your speakers to blend in with a colored wall, now is

the time to paint your speakers outer frames and perforated grilles. The speakers outer surfaces

will accept ordinary latex wall paint or aerosol spray paint. Because the surface behind the grille

should remain unpainted, you will need to cover this area. Cover the speaker’s interior black

surface, woofer and tweeter. Paint the outer speaker frame and grille separately.

5. Attach the wire to the input terminals on the rear of the speaker. Remember to maintain

proper polarity with the amplifier by attaching the positive (+) lead to the red terminal and the

negative (-) lead to the black terminal.

Congratulations on choosing NXG In-Wall Loudspeakers. Like all NXG products, great care has

been taken in their design. Their combination of advanced engineering and state-of-the-art mate-

rials will provide you with years of listening pleasure, while blending smoothly into your home’s

decor. Before you get started, it is a good idea to identify all the parts and hardware (See Fig. 1).

FIG. 2

FIG. 3

Press on the

outer edge

of the tweeter

rim to rotate

NX-W5.2-LCR-P Video-Shielded Center/Left/Right In-Wall

Home Theater Speaker System

(Continued on reverse)

NXG In-Wall Speakers can be used as rear

surround sound channels by placing them (1) behind,

(2) on each side of viewer, or (3) as front main

home theater speakers. They also can be mounted

horizontally for a center-channel application (4).

Adjust

tweeter level

as shown

FIG. 4

FIG. 1

Speaker with

self-contained

mounting clamps

Cutout Template

Aluminum Grille with

foam inner backing

Grille

removal

tool

Black

grille

adhesive

Painting Mask

IR Sensor

Knockout

Tweeter Level Switch

FIG. 6

(Continued from front)

NXG Speakers Three-Year Limited Warranty

If the NXG speaker system proves to be defective in workmanship

or materials within three years from the date of the original cus-

tomer’s purchase, we will, at our option, repair or replace the

defective product.

Limitation of Implied Warranties

Any implied warranties, including warranties of merchantability

and fitness for a particular purpose, are limited in duration to the

length of this warranty.

Exclusion of Certain Damages

NXG’s liability for any defective product is limited to repair or

replacement of the product at our option. NXG shall not be liable for

incidental or consequential damages of any kind or character

because of product defects. Some states do not allow limitations

on how long an implied warranty lasts and/or do not allow the

exclusion or limitation of incidental or consequential damages, so

the above limitations and exclusions may not apply.

This Warranty Does Not Cover:

• Damage caused by abuse, accident, misuse, negligence, or

improper operation.

• Any product whose serial number has been altered, defaced,

or removed.

• Products that have been altered or modified.

• Normal wear and maintenance.

• Damages caused by shipping. (All claims for shipping damage

must be made with the carrier.)

Warranty Service

Warranty service must be performed by an authorized service

center, usually an NXG speaker systems dealer or its authorized

agent. You may obtain a list of authorized service centers by con-

tacting NXG. All warranty repairs must be accompanied by the

original bill of sales. No other document is acceptable or is

required. This warranty gives you specific legal rights, and you

may also have other rights which vary from state to state.

NXG reserves the right to revise speaker system specifications without notice.

New Construction

1. Determine speaker locations and mark them on your plans for future reference.

2. If possible, run speaker wires after HVAC and electrical wiring is in place.

3. Secure speaker wires in place along the run with insulated staples only and

be careful not to pierce the wire’s insulation. Allow a bit of slack for expan-

sion of building materials.

4. The actual speakers should not be installed until the wall board is in place.

In the meantime, leave several feet of wire coiled up and secured at the back

side of the mounting hole.

5. To complete the installation follow steps 2 through 5 above.

FIG. 5

6. See Fig. 6. With the speaker wire attached to the speaker, slide the speaker

up inside the cut-out hole. Center the speaker in the cut-out hole and turn the six

locking screws clockwise until the speaker is drawn up snugly to the wall board

from behind, clamping the speaker in place. Try to tighten each screw equally.

Replace the speaker grill by gently pressing it into place.

NX-W5.2-LCR-P Specifications

Tweeter: 1˝ (25mm) minimum-diffraction, pivoting,

fluid-cooled high tenacity teteron dome

Woofers: Dual magnetically-shielded 51

/4˝ (133mm)

metallic anodized, graphite-filled, injection-molded

RCT cones with rubber surrounds

Crossover: Optimized 12dB Electro Acoustic w/mylar

capacitors, air core inductors, and gold-plated

input terminals

Frequency Response: 45 Hz-22,000 Hz

Impedance: 8 ohms nominal, 6 ohms minimum

Power Handling: 5-120 watts

Sensitivity: 89dB @ 1 watt/1 meter

Grille: Corrosion-resistant, powder-coated aluminum

Overall Dimensions (H x W x D): 75/8˝ x 15˝ x 3 1/2˝

(194 mm x 381 mm x 89 mm)

Cutout Dimensions (H x W): 63/8˝ x 137/8

(162 mm x 352 mm)

Operational Check

After making all connections it’s a good idea to make sure everything is working

properly. Turn on your stereo system making sure the volume control is turned

down and that the balance control is in the center position. Activate a musical

source such as FM, a CD or DVD player. Gently turn up the volume. You should

hear music coming from your new NXG speakers. If no sound is heard from any

or all speakers, switch off the system immediately and check for open or loose

connections, wrong polarity or shorts.

16648 North 94th Street

Scottsdale, AZ 85260

1-800-733-0008

Product specificaties

Merk:	Nxg
Categorie:	Speaker
Model:	NX-W5.2-LCR-P

Heb je hulp nodig?

Als je hulp nodig hebt met Nxg NX-W5.2-LCR-P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Speaker Nxg

Nxg NX-W5.2-LCR-P Handleiding

7 Juli 2023

Nxg NX-W6.2-P Handleiding

7 Juli 2023

Nxg Onyx NX-C8.2-ENC-X Handleiding

1 Juli 2023

Nxg NX-C8.3-P Handleiding

29 Juni 2023

Nxg NX-C8.2-P Handleiding

28 Juni 2023

Nxg NX-AW5 Handleiding

3 November 2022

Handleiding Speaker

Nieuwste handleidingen voor Speaker

OTTO Bluetooth Revo NC2 Handleiding

20 April 2024

REL Acoustics Strata Handleiding

20 April 2024

REL Acoustics Strata III Handleiding

20 April 2024

Soen Transit Handleiding

18 April 2024

Miller & Kreisel MP300RC Handleiding

18 April 2024

Soen Transit XS Handleiding

18 April 2024

Miller & Kreisel MP7 Handleiding

18 April 2024

Qian QRBT1801 Handleiding

17 April 2024

Focal Twin6 Handleiding

17 April 2024

Kenwood KFC-WPS1000F Handleiding

16 April 2024