NuTone HDN6430SS Handleiding
Bekijk gratis de handleiding van NuTone HDN6430SS (8 pagina’s), behorend tot de categorie Afzuigkap. Deze gids werd als nuttig beoordeeld door 7 mensen en kreeg gemiddeld 4.5 sterren uit 4 reviews. Heb je een vraag over NuTone HDN6430SS of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
1
VERTICAL OR HORIZONTAL DISCHARGE
USING 3¼" x 10" DUCT
CUTOUT DIMENSIONS
TOP
VIEW
BACK
VIEW
18"
12"
6"
7⁄8"
3¼" x 10"
3¼" x 10"
ELEC. K.O.
9³⁄8"
1
7
⁄ "16
1
7
⁄ "16
7"
1"
1⁄2"
1⁄2"
SUPPLIED DUCT
TRANSITION
RANGE
HOOD
WALL
WALL
CAP
ELBOW
(
If required)
ROOF CAP
EAVE
CAP
3¼" x 10"
DUCT
C
L
INSTALLATION INSTRUCTIONSFOR HDN64 SERIES RANGE HOOD
READ & SAVE THESE INTRUCTIONS
IMPORTANT TRUCTIONSAFETY INS S
1. For indoor use only.
2. For general ventilating only. Do not use to exhaust hazardous or explosive
materials and vapors.
3. To reduce the risk of fire or electrical shock, this range hood shoul not
be used with an additional solid-state speed control device.
4. To reduce the risk of shock, disconnect power before servicing.
5. To reduce the risk of fire and to properly exhaust air, be sure to duct
air outside. Do not vent exhaust air into spaces within walls or ceilings
or into attics, crawl spaces or garages.
IMPORTANT TRUCTIONSAFETY INS S
WARNING - TO REDUCE THE RI K OF FIRE, ELECTRICS
SHOCK, OR INJURY TO PERS SON , OBSERVE THE
FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you
have any questions, contact the manufacturer at the address or
telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and lock
service panel to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by qualified person(s)
in accordance with all applicable codes and standards - including
fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to prevent
backdrafting. Follow the heating equipment manufacturer’s guidelines
and safety standards such as those published by the National Fire
Protection Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and local
code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
6. This unit must be grounded.
7. Ducted fans must always be vented to the outdoors.
8. To reduce the risk of fire, use only metal ductwork.
9. When applicable local regulations comprise more restrictive installation
and/or certification requirements, the aforementioned requirements
prevail on those of this document and the installer agrees to conform
to these at his own expenses.
10. When performing installation, servicing or cleaning this unit, it is
recommended to wear safety glasses and gloves.
TO REDUCE THE RI K OF A RANGE TOP GREA E FIRE:S S
1. Never leave surface units unattended at high settings. Boilovers cause
smoking and greasy spillovers that may ignite. Heat oils slowly on low
or medium setting.
2. Always turn hood ON when cooking at high heat or when flambeing
food (i.e.: Crêpes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
3. Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the size of
the surface element.
TO REDUCE THE RI K OF INJURY TO PER IN THE EVENT OFS S SON
A RANGE TOP GREA E FIRE, OBS SERVE THE FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal
tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - you may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - a violent
steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher, and you already know
how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
*Based on “Kitchen Fire Safety Tips” published by NFPA.
KITCHEN
CABINET
CUTOUT DIMENSIONS
WIRING
CUTOUT
5
1
⁄ "8
10¼"
3¾"
1
7
⁄ "16
HORIZONTAL DISCHARGE THROUGH WALL
7"
SUPPLIED DUCT
TRANSITION
RANGE HOOD
REMOVE DAMPER FLAP
FROM TRANSITION FOR
THIS INSTALLATION
WALL
WALL
CAP
18"
12"
6"
7⁄8 "
ELEC. K.O.
9³⁄8"
1
7
⁄ "16
7"
1⁄2"
1⁄2"
7"DIA
4
7
/ "8
RANGE HOOD
VERTICAL DISCHARGE USING 7" ROUND DUCT
(TRANSITION NOT INCLUDED)
ROOF CAP
ADJUSTABLE
ELBOW
7" ROUND
DUCT
ROOF
REMOVE BOTH
3¼" x 10" AND
4½" x 8"
KNOCKOUTS
FOR 7" DUCT
CUTOUT DIMENSIONS
TOP
VIEW
BACK
VIEW
C
L
1
7
⁄ "16
1"
FIGURE 1
FIGURE 3
3 300424 9A
FIGURE 2
REGISTER YOUR PRODUCT ON LINE AT
WWW.NUTONE.CA
INSTALLATION INSTRUCTIONSFOR HDN64 SERIES RANGE HOOD
READ & SAVE THESE INTRUCTIONS
PLANNING
• This hood can be connected to ductwork to discharge through the top
or the back of the hood to outside. It can also be installed without ducts
to return filtered air back into the room. For a ductless installation, a
separate filter is required.
Order conversion kit FKM65.
• Mounting height MUST BE at a minimum of 22” and at a maximum of
30” above the cooking surface from the bottom edge of the range
hood.
• The hood shall be mounted to the bottom of a standard wall cabinet.
If the hood must be mounted directly to a wall, secure the hood to wall
studs.
• All wiring must comply with local codes and the unit must be properly
grounded. Connection should be made to a 110-120 VAC lighting
circuit (15A) in the circuit breaker or fuse box.
IF THE RANGE HOOD I TO BE DUCTED:S
• Ductwork can be installed vertically or horizontally.
• Duct runs should be as short as possible.
• Avoid the use of elbows.
• Use metal duct tape at all joints.
• Do not use duct smaller than the discharge on the hood.
NON DUCTED:
• Disregard instructions for knockout.
• Discard the transition, it will not be used.
PREPARATION
1. Use the dimensional drawing to lay out the range hood’s mounting
holes, wiring access and ductwork.
2. Make cut-outs for wiring and ductwork.
3. If the hood is to be ducted, install the ductwork so that it is flush to the
range hood’s mounting surface.
• Refer to Figure 1 if the range hood is to be installed with a horizontal
discharge.
• Refer to Figure 2 if the range hood is to be installed with a vertical
discharge.
4. Remove the necessary duct opening and wiring knockout from the range hood.
NOTE: If the range hood is to be installed as a ducted unit, install
baffle plate (refer to figure 4) by sliding into place behind
grille. Use locator bumps to orient the grille.
NOTE: If the range hood is to be installed as a ductless unit, do
not remove any knockouts.
5. Run two-conductor wires (with ground) from a power source to the hood
location. Bring approximately 12” of wiring through wiring hole in cabinet.
6. Drill four 3 3/ 2” diameter pilot holes at points where mounting holes are
marked in the filler strips or cabinet bottom.
7. Insert four (4) mounting screw (not supplied), leaving approximately
1/4” of thread exposed. Use no. 8 or no. 10 round head screws.
IN TALLATIONS
1. Refer to Figure 6 for a vertical discharge installation.
Secure the ¼” x 10” transition (if used) to top of hood.3
Refer to Figure 7 for a horizontal discharge installation.
If using the supplied ¼” x 10” duct transition, remove the damper from 3
the transition to prevent possible venting interference. Position transition
into wall cutout (the transition does not fasten to the hood).
Refer to Figure 5 for 7” round discharge installation.
Secure 7” round adaptor to top of hood using screws provided.
2. Feed the wiring through the access hole and into the electrical box.
3. Align hood’s keyhole mounting slots over the four (4) partially installed screws.
4. Making sure the duct position over the hood’s duct transition (or adaptor),
push the hood against the rear wall. Secure hood by tightening screws.
5. Using a long blade screwdriver, reach into the discharge opening and
make sure the damper operates freely.
WIRING CONNECTIONS
All wiring connections must comply with local code and the unit must be
properly grounded.
1. Make sure box connector is secure.
2. Refer to Figure 8. Make wiring connections.
3. Replace electrical box cover and secure with screw.
7" ROUND
ADAPTER
(Not included)
SECURE TRANSITION
WITH SCREWS (included)
POSITION DUCT
TRANSITION IN
WALL CUTOUT
HORIZONTAL
WHITE
HOOD WIRING
SUPPLY WIRING
GROUND CREWS
BLACK
GREEN OR BARE
(GROUND)
BLACK
WHITE
LOCATORS
BAFFLE
PLATE
FIGURE 4
FIGURE 5
FIGURE 6
FIGURE 7
FIGURE 8
2
FILTER
CLIPS
FKM-65 FILTER
(FOR DUCTLESS
OPERATION ONLY)
ALUMINUM FILTER
COMPLETING ASSEMBLY
1. Install a 75 W (maximum) light bulb in the receptacle.
2. Install filter and light lens assembly.
3.For ductless use with charcoal filter (FKM-65): Install 2 filter clips by
sliding into the receivers on the sides of the hood fan housing.
See Figure 9.
OPERATION AND MAINTENANCE
FILTERS
IMPORTANT: The aluminium filter should be removed once a week and
washed in hot detergent water. Rinse in clear, warm water and shake off
excessive moisture before replacing. The filter may also be cleaned in
your dishwasher. Always install the aluminium filter with the domed side
away from the fan.
IN A NON-DUCTED INSTALLATION
Refer to Figure 9. In non-ducted installations use FKM-65 filter and
replace every -6 months as needed. Always install the FKM-65 filter first3
(nearest fan) with carbon side towards fan and the aluminium
filter second. Install filter clips by sliding into brackets on side of air chamber.
CLEANING
The hood should be wiped off occasionally both inside and outside using
warm water, mild dish detergent and a soft cloth. Never use scouring powders,
steel wool pads or any other abrasive cleaners, which will destroy the
hood’s finish.
FIGURE 9
3
INSTALLATION INSTRUCTIONSFOR HDN64 SERIES RANGE HOOD
READ & SAVE THESE INTRUCTIONS
Product specificaties
| Merk: | NuTone |
| Categorie: | Afzuigkap |
| Model: | HDN6430SS |
Heb je hulp nodig?
Als je hulp nodig hebt met NuTone HDN6430SS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Afzuigkap NuTone
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
Handleiding Afzuigkap
- FORS
- Adelberg
- Thor
- Gemini
- MPM
- AEG Electrolux
- Pando
- Zanussi
- Soler And Palau
- XO
- Point
- Master Kitchen
- Ilve
- Helios
- Porter & Charles
Nieuwste handleidingen voor Afzuigkap
18 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025