Nuc Electronics NFS-9000U - Combo 3 Food Processor Handleiding

Nuc Electronics Keukenmachine NFS-9000U - Combo 3 Food Processor

Lees hieronder de 📖 handleiding in het Nederlandse voor Nuc Electronics NFS-9000U - Combo 3 Food Processor (1 pagina's) in de categorie Keukenmachine. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Instruction Manual
updated in MAY, 2006
FOOD PROCESSOR InstruCtIon Manual
Important Safeguards
SAVE THESE INSTRUCTION
BOOKLET ADVANTAGES
OF FOOD PROCESSOR
For Juicer
ㆍRead all instructions carefully before using.
ㆍBlades are sharp. Please handle them with care.
ㆍDo not use the product outdoors.
ㆍVerify that the voltage in your home corresponds to that of your appliance.
ㆍDo not operate any appliance with damaged cord or plug, or after appliance has been dropped or
damaged in any way. Return the appliance to the nearest authorized service facility for examination,
repair or electrical or mechanical adjustment.
ㆍTo protect against the risk of electrical shock, do not put cord, plug, base, or motor in water or other liquid.
ㆍAlways unplug from outlet when not in use, before removing food and before cleaning.
To unplug, grasp plug and pull from electrical outlet. Never pull cord.
ㆍDo not let cord hang over the edge of table or counter, or touch hot surface.
ㆍKeep hands, spatulas and other utensils away from moving blades or discs while processing food,
to prevent the possibility of severe personal injury or damage to food processor.
A plastic scraper can be used, but only when the food processor motor is stopped.
ㆍAvoid contact with moving parts. Never push food down by hand when slicing or shredding.
Always use pusher, or injury can be occurred.
ㆍMake sure motor has completely stopped before removing cover
ㆍNever store any blade or disc on motor shaft, to reduce the risk of injury.
Store blades and discs out of reach of children.
ㆍMake sure that the cover and feed tube are securely locked in a place before operating food processor.
ㆍThe unauthorized use or not sold by NUC may cause fire, electrical shock or damage to
your food processor.
ㆍImmediately unplug and contact authorized service facility, during operation, when you hear
unusual sound or when you smell unusual or when you see smoke
ㆍPower full motor enables chops, minces, blends, mixes and emulsifies in a matter
of seconds, even very hard substances and fibrous vegetables.
ㆍMultipurpose functions such as juicing, mincing, chopping, mixing, doughing,
slicing, shredding and etc.
ㆍTwo ways safety system: Your food processor will not operate unless the work
bowl and work bowl cover are properly locked on the base.
ㆍDetachable system for multifunction and easy cleaning: The work bowl and
blades can be detachable, so you can choose accessories for your purpose and
can be cleaned with easy.
ㆍTwice wide mouth of feed tube than others, perfect for slicing whole fruits and
vegetables.
ㆍGood and state-of-art design
combo 3
For
Juicer
For
Crushing/
Chopping/
Mixer
For
Slice/
Shred
FOOD PROCESSOR FEATURES
OPERATING GUIDE SWITCH PANNEL JUICER ASSEMBLY INSTRUCTION
For Crushing/Chopping/Mixer
For Slice/Shred
FOOD PROCESSOR combo 3
04/05
FOOD PROCESSOR InstruCtIon Manual
combo 3
06/07
1. JUICING FUNCTION
ㆍPush “Low” button
ㆍNeed Juicing Screen
ㆍMake natural juice with fruits, carrot, cucumber and edible roots.
ㆍMake potato pan fried cake or croquette or tofu with Juicing Screen.
2. CRUSH FUNCTION
ㆍPush “High” button.
ㆍNeed Crush Blade.
ㆍMake flour with dried beans, parched adlay.
3. CHOPPING FUNCTION
ㆍPush “Off” button.
ㆍNeed Chopping Blade.
ㆍGarlic, onion, unripe hop pepper, dried pepper, fish, and meat can be chopped.
4. MIXING FUNCTION
ㆍPush “High” button.
ㆍNeed Crush Blade.
ㆍMake fibroid Juice with crushed fibroid fruits, vegetables along with beverage.
5. SHAVED ICE FUNCTION
ㆍPush “Off” button
ㆍNeed Chopping Blade
ㆍShave Ice
6. SHRED & SLICE FUNCTION
ㆍPush “Low” button
ㆍNeed Disc for Shred/Slice
ㆍShred/Slice with vegetables, carrots, radish, cucumbers, sweet potato, lotus root and onion.
1.Put Juicing Bowl on Base Body. Insert
Round Juicing Screen firmly as drawing.
2.Put Juicer Cover on Juicing Bowl and
lock firmly fixing clamps with both hands
till you hear click as drawing.
3.Put Waste Container to the Juicer Cover
outlet direction as drawing.
4.Put button first 3-5 seconds,
and then put materials.
REMARK: DISASSEMBLY CAN BE DONE CONVERSELY.
FOOD PROCESSOR InstruCtIon Manual
combo 3
08/09
CRUSHING/CHOPPING
ASSEMBLY INSTRUCTION
HOW TO USE BLADE OPENER
1.Insert desired blade into spindle axle of
Work Bowl as drawing.
FOOD PROCESSOR InstruCtIon Manual
combo 3
10/11
HOW TO USE DISC FOR SHRED/SLICE
WARRANTY
NOTICE BEFORE USE SLICE
HOW TO MAINTAIN
2.Put materials in Work Bowl first and
assemble Work Bowl Cover as drawing.
3.Put Work Bowl on Base Body, position
the side lockers of the Work Bowl to the
fixing clamps of Base Body. And lock
fixing clamps with both hands till you
hear click as drawing.
When the blade cannot be opened with you finger,
please use the blade opener as drawing.
4.Push button for working.
REMARK: DISASSEMBLY CAN BE DONE CONVERSELY.
Blade Opener
SHRED & SLICE ASSEMBLY
1.Put Slice Body on Base
Body and then position Slice
Bowl on the Slice Body to
the direction of the oval
sliced base Body as drawing.
2.Put Disc for Outlet on Slice
Body and then assemble
desired Disc for Shred/Slice
as drawing.
3.Put Slice Cover the direction
of the oval sliced base Body
as drawing.
4.Put Waster Container or other
Container to the direction of
Outlet as drawing
5.Push “Low” button, after 2-3
seconds, put materials with
Small/Large Feed Tube Pusher.
REMARK: DISASSEMBLY CAN BE DONE CONVERSELY.
You can use disc front or rear side according to desired function as table shown.
Slice Low
Shred Low
Function Material Shape Disc Direction Button Function
Slice for all kinds of vegetables,
radish, carrot, cucumber, sweet
potatoes, lotus root and onions.
Shred for radish, carrot, cucum-
ber, sweet potatoes, and onions.
1.Wash with warm water and neutral detergent
and wipe with a dishtowel. Do not use luffa.
Clean Round Juicing Screen with supplied
brush.(Be careful when you clean knives)
2.Be careful not to be wet Main Body and Slice
Bowl and wipe with dried dishtowel.
Water in motor can be caused mal-function or
electric shock.
3. When you wash the product, do not use
chemical product. If you use chemical
product, the color of product can be changed.
4. Do not put product in the direct ray of light or
humid area.
1.Be careful of knives for they are very sharp.
2.When you stop and want to open slice cover, be sure of complete stop of knife.
3.Do not push Small/Large Feed Tube Pusher too strongly to protect knife.
4.When you hear noise or vibration, stop machine and take out the remnants from knife and start again.
5.Please use Small Feed Tube Pusher only in Large Feed Tube Pusher.
GENERAL NOTICE BEFORE USE
ELECTRICAL SPECIFICATION
1.Make sure to use appropriate voltage.
2.Make sure of assembling status for main body, bowl, bowl cover and clamp.
3.For safety purpose, do not put the product near by children.
ITEM
VOLTAGE/HERZ
STANDARD WATTAGE
MODEL NUMBER
CONTINUOUS MAXIMUM USE
JUICER/MIXER/SLICER (COMBO 3)
120V, 60Hz
350W
NFS-9000U
3 MINUTES
#679 CHIMSAN-3DONG, BUKGU, DAEGU-CITY, R.O.KOREA
TEL. 82-(0)53-665-5066 FAX. 82-(0)53-353-7018
Homepage. http://www.nuc.co.kr
NUC Electronics Co., Ltd. and its authorized dealers guarantee this product against defects for 12
months from date of purchase for all parts and 5 years for motors and will replace them as
follows:
1. NUC and its authorized dealers shall replace any and all parts (12 months from the date of
purchase) at no charge if this product is defective due to faulty materials or manufacturing.
After the warranty period you must pay for all charges including parts, labor, shipping and
handling.
2. To receive service from authorized dealers, you must present the proof of purchase, showing
name and address of supplier, together with the date of purchase. You must also supply, in
writing, your name and full address including postcode, together with a contact telephone
number, detailing any fault in full. The Proof of Purchase in the form of a bill of sale or
receipted invoice, which is evidence that the unit is within the warranty period, must be
presented to receive warranty service.
3. When returning the product to authorized dealer, the item should be packed carefully in a
carton box with protective materials inside to avoid damage during transportation.
4. This warranty does not cover wear and tear, cosmetic damage or damage due to acts of nature,
accident, misuse, abuse, negligence, commercial use, or modification of, or to any parts of the
product, including the accessories. This warranty does not cover damage due to improper
operation or maintenance, use of improper voltage supply or attempted repair by anyone other
than a facility authorized by NUC to service the product. This warranty is valid all over the
world.
5. This warranty is in addition to the consumer’s statutory rights and does not diminish the above
rights in any way.
REFAIR/REPLACEMENT AS PROVIDED UNDER THIS WARRANTY
IS AVAILABLE EXCLUSIVELY TO THE CONSUMER. NUC SHALL
NOT BE LAIBLE FOR ANY INCIDENTAL OR CONSEQUENTAL DAM-
AGES FOR BREACH OF ANY EXPRESS OR IMPRIED WARRANTY
ON THIS PRODUCT. EXCEPT TO THE EXTENT PROVIDED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PROD-
UCT IS LIMITED IN DURATION TO THIS WARRANTY.
IMPORTANT SAFEGUARDS
FOOD PROCESSOR FEATURES
OPERATING GUIDE SWITCH PANNEL
JUICER ASSEMBLY INSTRUCTION
CRUSHING/CHOPPING ASSEMBLY INSTRUCTION
SHRED & SLICE ASSEMBLY
HOW TO USE DISC FOR SHRED/SLICE
ELECTRICAL SPECIFICATION
WARRANTY
03
04
06
07
08
09
10
11
12
Table of Contents
NUC ELECTRONICS CO., LTD.
Feed Tube Pusher
Round Juicing Screen
Juicer Cover
Cleaning Blush
Stainless Juicing Bowl
Waste Container
Base (common use)
Fixing Clamp
Base (common use)
Fixing Clamp
Base (common use)
Fixing Clamp
Air Cover
Work Bowl Cover
Work Bowl
Blade for Chop/Dough
Blade for Crush
Blade Opener
Small Feed Tube Pusher
Large Feed Tube Pusher
Slice Cover
Disc for slice
Disc for shred
Disc for Outlet
Slice Bowl
Slice Body

Product specificaties

Merk: Nuc Electronics
Categorie: Keukenmachine
Model: NFS-9000U - Combo 3 Food Processor

Heb je hulp nodig?

Als je hulp nodig hebt met Nuc Electronics NFS-9000U - Combo 3 Food Processor stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Keukenmachine Nuc Electronics

Nuc Electronics

Nuc Electronics NFS-9000U - Combo 3 Food Processor Handleiding

9 Oktober 2023
Nuc Electronics

Nuc Electronics NUC-4300U - Yogurt maker Handleiding

9 Oktober 2023
Nuc Electronics

Nuc Electronics Red Ginseng Maker Handleiding

9 Oktober 2023
Nuc Electronics

Nuc Electronics Herb Brewing Maker Handleiding

9 Oktober 2023
Nuc Electronics

Nuc Electronics NJM-9000U Combo Handleiding

9 Oktober 2023
Nuc Electronics

Nuc Electronics Power Blender 3000 Handleiding

9 Oktober 2023

Handleiding Keukenmachine

Nieuwste handleidingen voor Keukenmachine

Dash

Dash Masha 2X DMA001 Handleiding

10 April 2024
Philips

Philips Cucina HR7633 Handleiding

8 April 2024
Philips

Philips HR7772 Handleiding

5 April 2024
Philips

Philips Viva Collection HR2515 Handleiding

3 April 2024
Philips

Philips Viva Collection HR7757 Handleiding

3 April 2024
LERAN

LERAN HMX 0576 M Handleiding

31 Maart 2024
Max Pro

Max Pro 330012 Handleiding

31 Maart 2024
Binatone

Binatone MFP 414 Handleiding

31 Maart 2024
Max Pro

Max Pro 330010 Handleiding

31 Maart 2024
Sage

Sage the Kitchen Wizz Pro BFP800 Handleiding

27 Maart 2024