NiteRider Pro 3600 Enduro Remote Handleiding
NiteRider
Fietslampen
Pro 3600 Enduro Remote
Lees hieronder de đ handleiding in het Nederlandse voor NiteRider Pro 3600 Enduro Remote (2 pagina's) in de categorie Fietslampen. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
PRO 2800 ENDURO REMOTE
PRO 3600 ENDURO REMOTE
USER GUIDE
Now with Remote Switch
MOUNTING THE HEADLAMP
The Pro 2800 / 3600 Enduro headlamp can be mounted to the
handlebar or a helmet.
Universal Handlebar Mount
The Universal Handlebar Mount (UHM) is designed to ît on virtually
any handlebar. Included with the mount is a 2.5 mm Allen wrench
for adjusting the mount.
1. Turn the knob counter-clockwise, allowing the hinge to swing open.
2. Place the UHM on the handlebar on the left side of the stem,
orienting the rectangular notch in the slider clip to the rear.
3. Swing the hinge down to make contact with the handlebar.
4. Swing the bolt up, seating the knob into its recess.
5. Turn the knob clockwise to tighten and secure the mount
to the handlebar.
The UHM can be adjusted to accommodate any handlebar angle.
By loosening the 2.5 x 30 mm Allen screw, you can move the
swing arm back and forth to straighten the headlamp.
Tighten the 2.5 x 30 mm screw after the adjustment. To pivot the
headlamp, loosen the 2.5 x 12 mm screw located under the slider
clip and swing arm and rotate the headlamp to the desired position.
Make this adjustment before tightening the 2.5 x 30 mm screw.
Inserting the Headlamp into the Handlebar
Insert the headlamp into the handlebar or helmet mount slider clip
from the rear moving forward. Gently rocking the lamp as you slide it
may help. Do not push the release lever when inserting the headlamp
into the slider clip; let the lamp snap into place by itself.
To remove the headlamp, push the release lever forward and slide the
lamp backward.
Note: After mounting the headlamp, adjust it so the beam illuminates the roady without
distracting oncoming riders.
USE THE LIGHT THAT PROS USE
NiteRider⢠provides mountain bike riders the most durable, reliable
and best performing lights in the market. Itâs not a statement we make
lightly, as the backbone of our success has been built on providing
lights of exceptional quality to this very demanding market sector.
Through 22 years of actively supporting professional riders at 12 and
24 hour endurance events we have learned what it takes to become
the stand alone leader in mountain bike lighting.
PARTS LIST AND IDENTIFICATION
Please verify the contents of your Pro 2800 / 3600 Enduro system:
A. Pro 2800 / 3600 Enduro Headlamp
B. Remote Switch
C. Li-Ion Enduro Battery
D. Universal Handlebar Mount (UHM)
E. 36â Extension Cable
F. AC Adapter
C.
D.
E. F.
A.
B.
CLICK!
Handlebars not included
MOUNTING THE BATTERY
Warning: For safety reasons, a cyclist should never be tethered to
the bike. If the headlamp is mounted to the helmet, do not mount
the battery to the frame. Conversely, if the headlamp is mounted
to the handlebar, do not place the battery in a pocket or pack.
Frame Mount
1. Thread the hook/loop straps through the two slots on the bottom
of the battery.
2. Attach the concave surface of the battery to a safe,convenient
location on the frame (typically under the top or down tube),
placing the hook/loop strap over the tube, but under any shift
or brake cables. The cable from the battery should extend
toward the stem.
3. Secure the headlamp and battery cable to the frame using the
thin hook/loop strapettes. Make sure the cables do not interfere
with any moving parts.
OPERATION
1. Connect the headlamp cable to the battery.
2. Press and release the headlamp power button to turn the light on.
Cycle through the four brightness levels by pressing and releasing
the power button.
3. To access the daylight safety î
ash mode, press and hold the
power button until the headlamp starts to î
ash.
4. With the headlamp in î
ash mode, press and release the power
button to access beacon, SOS or walk modes. From walk mode
you can return to normal mode by pressing and releasing the
power button.
5. To turn the headlamp oî from normal, î
ash or walk modes, press
and hold the power button until the headlamp shuts oî.
6. Always disconnect the battery from the headlamp when
transporting the light system. This prevents accidentally
turning on the headlamp, which may cause overheating
î andîpotentialîdamageîfromîhighîheatîorîevenîaîriskîofîîre.
PROTECTING YOUR INVESTMENT
Properly charge your battery to maximize its lifespan (see the
âBattery Charging and Careâ section for detailed information).
The Pro 2800 / 3600 Enduro will perform in wet weather conditions,
but submerging it in water will damage the system.
SUPPORT
If you experience diîculties during product installation or operation,
NiteRider⢠provides free telephone support on weekdays from
8:00 am to 4:30 pm (Paciîc Time) at 800.466.8366, Ext 4.
You may also e-mail us at support@niterider.com.
WARRANTY
NiteRider⢠stands behind its products with the following warranties:
⢠Lifetime warranty on all mechanical components
⢠2 Years on electrical components
⢠1 Year on rechargeable batteries
To obtain warranty service, it is preferable to have your original
sales receipt. Contact the NiteRider⢠Customer Service
Department at 800.466.8366, Ext. 4 to obtain a Return
Merchandise Authorization (RMA) number. The RMA number
must be prominently displayed on the outside of your package.
The product must be properly packaged to prevent damage
in transit.
For complete warranty information, please visit our website at
www.NiteRider.com.
RUN TIMES
RIDING AT NIGHT CONT.
⢠Carry an auxiliary light and emergency supplies
⢠Make sure the headlamp, mounting bracket
and battery are securely fastened
⢠Always disconnect the battery from the headlamp
when transporting the light system
NiteRider⢠Technical Lighting Systems, Inc.
8295 Aero Place, Suite 200
San Diego, CA 92123
www.NiteRider.com
OPERATION (cont.) Fuel Gauge
The 8-step, LED Fuel Gauge is located on top of the headlamp in
front of the power button. When all four LEDâs are lit solid green,
the battery is fully charged. As the battery discharges â
increments
of capacity, the LEDâs from right to left, successively go from
solid green to blinking green, to out. With only the înal â
capacity
remaining one LED blinks red. At this time, the headlamp should
be turned oî and the battery recharged.
BATTERY CHARGING AND CARE
1. Plug the AC Adapter into an electric outlet, then plug the cable
from the AC Adapter into the battery.
2. The LED indicator on the battery will turn red while the battery
is charging. When the battery is fully charged, the LED will
turn blue.
3. Unplug the AC Adapter from the battery by grasping the
connectors rather than the cable.
4. Leaving the battery and AC Adapter connected indeînitely will
not harm the battery or AC Adapter.
5. When storing for an extended period of time, charge the battery
every three months to maximize its lifespan.
USB OUTPUT PORT
Your battery pack is equipped with a USB output port for
convenient recharging of electronic devices.
1. Plug in your USB adapter cord (not supplied) into USB output
port, then connect your electronic device to charge.
Please note to power off lighting system before recharging your electronic device.
RIDING AT NIGHT
While a Pro 2800 / 3600 Enduro lighting system will improve your
view, control and enjoyment of night riding, please remember that
cycling at night is an inherently dangerous activity. In addition to
using your lighting system properly and riding with extreme caution,
NiteRider⢠urges you to:
⢠Never ride alone
⢠Always let someone know where you are going
â˘îWearîaîhelmetîandîreî
ectiveîclothing
*Run times are approximations and will vary.
**Race mode is intended for endurance races.
PRO 2800 ENDURO REMOTE
Low 6:00h 825 Lumens
Med 3:00h 1400 Lumens
High 1:30h 2800 Lumens
Flash >56:00h
Race 17:00h 375 Lumens
Walk 56:00h 125 Lumens
PRO 3600 ENDURO REMOTE
Low 6:00h 1000 Lumens
Med 3:30h 1800 Lumens
High 1:30h 3600 Lumens
Flash >16:30h
Race 16:30h 450 Lumens
USB OUTPORT PORT
Product specificaties
| Merk: | NiteRider |
| Categorie: | Fietslampen |
| Model: | Pro 3600 Enduro Remote |
Heb je hulp nodig?
Als je hulp nodig hebt met NiteRider Pro 3600 Enduro Remote stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Fietslampen NiteRider
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
Handleiding Fietslampen
- Fietslampen Axa
- Fietslampen Sigma
- Fietslampen Silva
- Fietslampen Trelock
- Fietslampen Crivit
- Fietslampen Kayoba
- Fietslampen Lezyne
- Fietslampen Topeak
- Fietslampen BBB
- Fietslampen Busch And MĂźller
- Fietslampen Cateye
- Fietslampen Monkeylectric
- Fietslampen Spanninga
Nieuwste handleidingen voor Fietslampen
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022