NetworX NX-148E LCD Keypad Handleiding

NetworX Beveiliging NX-148E LCD Keypad

Lees hieronder de 📖 handleiding in het Nederlandse voor NetworX NX-148E LCD Keypad (24 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24

NetworX™ Series

NX-148E LCD Keypad

Installation and Setup

Includes models NX-148E, NX-148E-CF, and NX-148E-CF-W

LCD KEYPAD

These instructions do not purport to cover all details or variations in equipment nor to provide every

possible contingency to be met during installation, operation, and maintenance. If further information is

desired or if particular problems arise that are not covered sufficiently for the purchaser’s purpose, the

matter should be referred to GE Security, USA.

This document contains proprietary information of GE Security, USA and is furnished to its customer

solely to assist that customer in the installation, testing, operations, and/or maintenance of the equipment

described. This document shall not be reproduced in whole or in part nor shall its contents be disclosed to

any third party without the written approval of GE Security.

Please refer to the current GE Security product catalog for detailed warranty information.

Main

800-727-2339 Technical Support 888-437-3287

Outside the US 903-845-6941 Sales & Literature 800-547-2556

Main Fax 903-845-6811 Web: www.ge-security.com

SAFETY SYMBOL LEGEND

Warning

Indicates a procedure, practice, condition, or statement that, if not strictly observed,

could result in personal injury.

* This symbol indicates electrical warnings and cautions.

Caution

Indicates a procedure, practice, condition, or statement that, if not strictly observed,

could result in damage to or destruction of equipment or property.

** This symbol indicates general warnings and cautions.



Note

Indicates an essential or important procedure, instruction, condition, or statement.



Tip

Indicates a user tip. Provides helpful information that is not normally defined in

regular use, but from an experienced user.



Enter Indicates a key or button should be pressed to enter data.

LCD KEYPAD 3

Table of Contents

1. ENTERING THE PROGRAM MODE.......................................................................................................4

2. SELECTING THE MODULE TO PROGRAM ........................................................................................ 4

3. PROGRAMMING A LOCATION.............................................................................................................. 4

3A. NUMERICAL DATA......................................................................................................................... 4

3B. BINARY DATA................................................................................................................................. 5

3C. CHARACTER DATA........................................................................................................................ 5

4. LOADING FACTORY DEFAULTS........................................................................................................... 7

5. ENROLLING................................................................................................................................................. 7

6. PROGRAMMING THE KEYPADS........................................................................................................... 8

6A. USING THE FUNCTION MENU ..................................................................................................... 8

6B. ADJUSTING THE VIEW & BRIGHTNESS OF THE LCD ............................................................ 9

6C. CUSTOM MESSAGES...................................................................................................................... 9

6D. CUSTOM MESSAGES IN LANGUAGE 2 .................................................................................... 10

6E. SET KEYPAD OPTIONS................................................................................................................ 10

6F. SET KEYPAD NUMBER AND PARTITION................................................................................ 11

7. KEYPAD FUNCTIONS.............................................................................................................................. 12

7A. READING THE EVENT LOG ........................................................................................................ 12

7B. SET ELAPSED TIME IN MINUTES SINCE LAST AUTOTEST................................................. 13

7C. SET SYSTEM TIME AND DATE .................................................................................................. 14

7D. ADJUST KEYPAD TONE............................................................................................................... 14

7E. VIEW ZONE STATUS.................................................................................................................... 14

7F. VIEW ALARM MEMORY.............................................................................................................. 15

7G. TEST FUNCTION............................................................................................................................ 15

7H. DISPLAY TEST FUNCTION.......................................................................................................... 15

7I. LIGHT CONTROL FOR X-10 DEVICES....................................................................................... 15

7J. HOUSE CODES FOR X-10 DEVICES........................................................................................... 16

7K. CHANGE LANGUAGES ................................................................................................................16

7L. CHANGING USER CODES............................................................................................................ 16

7M. ASSIGNING AUTHORITY LEVEL............................................................................................... 17

7N. RESET FUNCTION......................................................................................................................... 18

7O. OTHER FUNCTIONS...................................................................................................................... 18

8. PARTITIONED SYSTEMS OPERATION.............................................................................................. 19

8A. MASTER MODE ............................................................................................................................. 19

8B. “TEMPORARY” MASTER MODE ................................................................................................ 19

8C. LIGHTS IN PARTITIONING MASTER MODE............................................................................ 19

8D. DISPLAYS IN THE PARTITIONING MASTER MODE.............................................................. 20

9. SERVICE DISPLAY................................................................................................................................... 21

10. MAXIMUM WIRE RUN............................................................................................................................ 23

11. SPECIFICATIONS..................................................................................................................................... 24