Netgear ProSafe ANT32405 Handleiding

Netgear Niet gecategoriseerd ProSafe ANT32405

Lees hieronder de 📖 handleiding in het Nederlandse voor Netgear ProSafe ANT32405 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 94 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
)NSTALLATION'UIDE
• ProSafe 5dB Omni-directional Indoor 3x3 Antenna ANT32405
• Wall-mounting kit
• Installation Guide (this guide)
• Warranty/Support card
Note: For optimal results in extending wireless range with antenna installations,
consult a qualified professional installer service for a site survey and proper
installation. For a list of devices approved by the FCC for use with the antenna, see
the NETGEAR website at http://tools.netgear.com/legal/fcc_antennas.html.
To maximize coverage and performance, place the antenna within the line of sight
of your wireless devices. Minimize partitions and objects that block the line of
sight if possible. The antenna can be placed
on a flat surface,
wall mounted, or
magnet mounted.
• If wall-mounting, place the antenna on an interior wall above cubicles
(cubicles generally include a metal foil). Ideal placement is 2 meters (6.5 feet)
high.
• If the wireless access point, router, or gateway, is in an IT room, place the
antenna outside the room against a a wall and close to the ceiling.
The area close to, behind, or beside the antenna will be covered, because the
dynamic range of the WLAN transmitter/receiver and antenna is
approximately 100 dB. Even with 20 dB to 40 dB or attenuation, the signal
strength is still strong and communication is maintained.
• The antenna has magnets in the base,
which can be used to mount it on metal
cabinets, white boards, or even the
ceiling cross bars (the framework that
holds the ceiling panels up).
Omni-directional
antenna ANT32405
Approximate
coverage area
Turn off your wireless access point, and connect your ANT32405 antenna. If your
wireless access point is new, follow the access point installation instructions. If you
are upgrading an existing access point, turn it on again.
ProSafe 5dB Omni-directional Indoor 3x3 Antenna ANT32405
Specifications
Frequency range 2.4~2.5GHz
Impedance 50 ohm
Gain 5dBi@ 2.45 GHz (excluding cable loss)
Cable loss can be up to 2dBi max
Operating temperature –10 to 60° C (14 to 140° F)
Storage temperature –10 to 70° C (14 to 158° F)
Humidity 95% RH
Dimensions (l x w x h) 100 x 65 x 175 mm (4 x 2.6 x 6.9 in)
Weight 237 grams (8.35 oz)
Connector Reverse N female
Warranty 2 year
This symbol was placed in accordance with the European Union Directive 2002/96 on the
Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the
European Union, this product should be treated and recycled in accordance with the laws of
your jurisdiction implementing the WEEE Directive.
© 2009 by NETGEAR, Inc. All rights reserved. NETGEAR, the NETGEAR logo, and ProSafe are
trademarks or registered trademarks of NETGEAR, Inc. in the United States and/or other countries.
Other brand and product names are trademarks or registered trademarks of their respective holders.
Information is subject to change without notice.
May 2009
Thank you for selecting NETGEAR products.
After installing your switch, locate the serial number on the label of your product and
use it to register your product at http://www.NETGEAR.com/register. Registration is
required before you can use our telephone support service. Registration via our website
is strongly recommended.
Go to http://kbserver.netgear.com for product updates and Web support. For Warranty
and Customer Support information see the Customer Support card that came with you
product.
In the interest of improving internal design, operational function, and/or reliability, NETGEAR
reserves the right to make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the
product(s) or circuit layout(s) described herein.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
To comply with FCC regulations, the ANT32405 should only be used with devices that have been
FCC approved for use with the NETGEAR ANT32405. Check the NETGEAR website at
http://tools.netgear.com/legal/fcc_antennas.html for an updated list of FCC approved devices.
Note: This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient
or relocate the receiving ante
nna; (2) Increase the separation
between the equipment and receiver; (3) Connect the equipment to an outlet or circuit different
from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV
technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. To avoid the possibility of exceeding the FCC radio frequency exposure limits,
human proximity to the antenna must be less than 20 cm (8 inches) during normal operation.
This device should not be co-located with other transmitters.
For EU, use of any antenna requires careful planning and extra considerations to comply with EU
emissions and health standards and regulations. Antenna installation must comply with the
maximum level authorized by each country.

Product specificaties

Merk: Netgear
Categorie: Niet gecategoriseerd
Model: ProSafe ANT32405

Heb je hulp nodig?

Als je hulp nodig hebt met Netgear ProSafe ANT32405 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Netgear

Netgear

Netgear WBE750 Handleiding

25 Maart 2024
Netgear

Netgear GS108MX Handleiding

25 Maart 2024
Netgear

Netgear WBE758 Handleiding

27 Februari 2024
Netgear

Netgear WAX214PAv2 Handleiding

27 December 2023
Netgear

Netgear APS1200Wv2 Handleiding

23 November 2023
Netgear

Netgear APS350W Handleiding

23 November 2023
Netgear

Netgear APS600Wv3 Handleiding

23 November 2023
Netgear

Netgear APS2000Wv2 Handleiding

23 November 2023
Netgear

Netgear APS600Wv2 Handleiding

23 November 2023
Netgear

Netgear GS108X Handleiding

23 November 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024
Sony

Sony PDW-U4 Handleiding

26 April 2024
Sony

Sony NXL-FR318 Handleiding

26 April 2024