Nec PlasmaSync 50VP2 Handleiding

Nec Monitor PlasmaSync 50VP2

Lees hieronder de 📖 handleiding in het Nederlandse voor Nec PlasmaSync 50VP2 (66 pagina's) in de categorie Monitor. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/66
User’s Manual
Bedienungshandbuch
Manuel de l'utilisateur
E-2
PLASMA MONITOR
Important Information
Warnings and Safety Precaution
The NEC plasma monitor is designed and manufactured to pro-
vide long, trouble-free service. No maintenance other than clean-
ing is required. Use a soft dry cloth to clean the panel. Never use
solvents such as alcohol or thinner to clean the panel surface.
The plasma display panel consists of ne picture elements (cells).
Although NEC produces the plasma display panels with more than
99.99 percent active cells, there may be some cells that do not
produce light or remain lit.
For operating safety and to avoid damage to the unit, read care-
fully and observe the following instructions.
To avoid shock and re hazards:
1. Provide adequate space for ventilation to avoid internal heat
build-up. Do not cover rear vents or install in a closed cabinet
or shelves.
The unit is equipped with cooling fans. If you install the unit in
an enclosure, be sure there is adequate space at the top of the
unit to allow hot air to rise and escape.
If the monitor becomes too hot, the overheat protector will be
activated and the monitor will be turned o. If this happens,
turn o the power to the monitor and unplug the power cord. If
the room where the monitor is installed is particularly hot, move
the monitor to a cooler location, and wait for the monitor to
cool for 60 minutes. If the problem persists, contact your NEC
dealer for service.
2. Do not use the power cord polarized plug with extension cords
or outlets unless the prongs can be completely inserted.
3. Do not expose unit to water or moisture.
4. Avoid damage to the power cord, and do not attempt to modify
the power cord.
5. Unplug unit during electrical storms or if unit will not be used
over a long period.
6. Do not open the cabinet which has potentially dangerous high
voltage components inside. If the unit is damaged in this way
the warranty will be void. Moreover, there is a serious risk of
electric shock.
7. Do not attempt to service or repair the unit. NEC is not liable
for any bodily harm or damage caused if unqualied persons
attempt service or open the back cover. Refer all service to
authorized NEC Service Centers.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALI-
FIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated volt-
age within the unit may have sucient magnitude
to cause electric shock. Therefore, it is dangerous
to make any kind of contact with any part inside of
this unit.
This symbol alerts the user that important litera-
ture concerning the operation and maintenance
of this unit has been included. Therefore, it should
be read carefully in order to avoid any problems.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EX-
POSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT
USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION
CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE
PRONGS CAN BE FULLY INSERTED. REFRAIN FROM
OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE
COMPONENTS INSIDE. REFER SERVICING TO QUALI-
FIED SERVICE PERSONNEL.
WARNING
This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be re-
quired to take adequate measures.
Precautions
Please read this manual carefully before using your NEC plasma
monitor and keep the manual handy for future reference.
CAUTION
PLASMA MONITOR
E-3
NOTE:
When you connect a computer to this monitor, attach the sup-
plied ferrite cores. If you do not do this, this monitor will not
conform to mandatory FCC standards.
Attaching the ferrite cores.
Set the ferrite cores on both ends of the DVI cable (not sup-
plied), and at one end of the power cable (supplied).
Close the lid tightly until the clamps click.
Set side
(Plasma Monitor side)
DVI cable (not supplied)
core (small) core (small)
Connector
Power cable (supplied) core (large)
band band
band
Recommendations to avoid or minimize phosphor
burn-in
Like all phosphor-based display devices and all other gas plasma
displays, Plasma monitors can be susceptible to phosphor burn
under certain circumstances. Certain operating conditions, such
as the continuous display of a static image over a prolonged pe-
riod of time, can result in phosphor burn if proper precautions are
not taken. To protect your investment in this NEC plasma moni-
tor, please adhere to the following guidelines and recommenda-
tions for minimizing the occurrence of image burn:
* Always enable and use your computer's screen saver function
during use with a computer input source.
* Display a moving image whenever possible.
* Always power down the monitor when you are nished using it.
NEC has built-in several operating modes in your PlasmaSync PD
Series monitor to help you reduce the likelihood of phosphor burn.
These are called the AccuShield Phosphor Protection System. If
the Plasmasync monitor is in long-term use or continuous opera-
tion, use the functions available in AccuShield to reduce the likeli-
hood of perceptible phosphor burn or to diminish its perceptible
eects if it occurs. See pages E-34, 42 and 43 for instructions on
how to use the Orbiter, Low Brightness and Inverse RGB modes
of AccuShield.
* Lower the Brightness and Contrast levels as much as possible
without impairing image readability.
* Display an image with many colors and color gradations (ie.
photographic or photo-realistic images).
* Create image content with minimal contrast between light and
dark areas. For example white characters on black backgrounds.
Use complementary or pastel colors whenever possible.
* Avoid displaying images with few colors and distinct, sharply
dened borders between colors.
Contact NEC Technologies at 1-800-836-0655 for other recom-
mended procedures that will best suit your particular application
needs.
To avoid damage and prolong operating life:
1. Use only with 120V 50/60Hz AC power supply. Continued op-
eration at line voltages greater than 120 Volts AC will shorten
the life of the unit, and might even cause a re hazard.
2. Handle the unit carefully when installing it and do not drop.
3. Set the unit away from heat, excessive dust, and direct sun-
light.
4. Protect the inside of the unit from liquids and small metal ob-
jects. In case of accident, unplug the unit and have it serviced
by an authorized NEC Service Center.
5. Do not hit or scratch the panel surface as this causes aws on
the surface of the screen.
6. For correct installation and mounting it is strongly recom-
mended to use a trained, authorized NEC dealer.
7. As is the case with any phosphor-based display (like a CRT
monitor, for example) light output will gradually decrease over
the life of a Plasma Display Panel.
Important Information


Product specificaties

Merk: Nec
Categorie: Monitor
Model: PlasmaSync 50VP2

Heb je hulp nodig?

Als je hulp nodig hebt met Nec PlasmaSync 50VP2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Monitor Nec

Handleiding Monitor

Nieuwste handleidingen voor Monitor