Native Instruments Traktor Pro Handleiding
Native Instruments
Softwarelicentie & -uitbreiding
Traktor Pro
Bekijk gratis de handleiding van Native Instruments Traktor Pro (7 pagina’s), behorend tot de categorie Softwarelicentie & -uitbreiding. Deze gids werd als nuttig beoordeeld door 53 mensen en kreeg gemiddeld 4.9 sterren uit 27 reviews. Heb je een vraag over Native Instruments Traktor Pro of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/7
Cable Tester NS-468
Safety instructions
· Do not use the cable tester NS-468 if it is damaged.
· This device is only for use inside dry and clean rooms.
· This device must be protected from moisture, splash water and impact of heat .
Intended use
The cable tester is used for fast testing of ISDN-, and network cable (RJ11, RJ45).
Configuration and shielding will be tested. Installed cable could be also tested.
Another employment than indicated is not permissible!
Changes can lead to the damage of this product, beyond that is this connected with dangers, like e.g.
short-circuit, fire, electrical impact etc.
For all special and personal injuries, which occur of not intended use, not the manufacturer, but the
operator is responsible.
Please note that serving and/or connection errors lie outside of our sphere of influence.
Understandably we cannot take over any adhesion for damage, which occur from it.
The entire product may not be changed and/or converted!
1
Preparation / Measurement
No energized lines measure!
Insertion of battery:
To insert the battery (9 V-Block) remove battery cover from MASTER-Device. Connect the battery
clip to the battery.
For operations of the REMOTE-device there is no battery needed.
Plugs / Cable:
1- 2-
RJ45 RJ12 / RJ11
Measurement:
· Connect the plugs of the cable which can be measured with the suitable sockets of the
MASTER and the Remote device.
· By pushing the switch to „ON“ -Position you turn the device to „FAST Test Modus“. Here each
individual contact of the cable is successively examined. The electrical connection is indicated
at the MASTER and at the REMOTE device over an LED.
· By pushing the switch to „S“-Position you turn the device to „SLOW Test Modus.
· By pushing the switch to „OFF“-Position you turn the device off.
· The result of measurement is indicated over the status LEDs (see table of the most usual
connections) at both devices. At cable with shielding shines additionally the “G “- LED
Kabel Stecker Anzeige MASTER Anzeige REMOTE
Cable Display
Master
Display
Remote
RJ45-Network cable (1:1,
completely connected, with
shielding)
1-2-3-4-5-6-7-8-G 1-2-3-4-5-6-7-8-G
RJ45-Network cable (crossover,
completely connected, without
shielding)
1-2-3-4-5-6-7-8 1-4-3-2-5-6-7-8
ISDN-Cable, 4-pin 3-4-5-6 3-4-5-6
RJ12-Cable, 6-pin 1-2-3-4-5-6 1-2-3-4-5-6
RJ11-Cable, 4-pin 2-3-4-5 2-3-4-5
2
Product specificaties
| Merk: | Native Instruments |
| Categorie: | Softwarelicentie & -uitbreiding |
| Model: | Traktor Pro |
Heb je hulp nodig?
Als je hulp nodig hebt met Native Instruments Traktor Pro stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Softwarelicentie & -uitbreiding Native Instruments
26 Augustus 2023
26 Augustus 2023
24 April 2023
15 April 2023
18 Februari 2023
15 Februari 2023
5 Februari 2023
22 Januari 2023
20 Januari 2023
Handleiding Softwarelicentie & -uitbreiding
- Mobotix
- Kaspersky Lab
- Avaya
- Acronis
- Eizo
- Steinberg
- Quark
- CyberLink
- AMX
- Microsoft
- Zebra
- LevelOne
- Neets
- Lancom
- Canon
Nieuwste handleidingen voor Softwarelicentie & -uitbreiding
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
16 April 2025
25 Februari 2025
14 December 2024
18 November 2024
14 November 2024