NAD MDC DAC 2.0 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor NAD MDC DAC 2.0 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 86 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
®
ASYNCHRONOUS USB DAC MODULE
Mounting Instructions
MOUNTING INSTRUCTIONS FOR THE C375BEE
The DAC Module is compatible with C375BEE. Using the supplied exible at
cable (FFC), DC power connector and screws, the DAC Module can be installed
in a C375BEE by undertaking the following procedure.
Note that if the C375BEE has a PP375 Phono Preamplier Module already
installed, the DAC module and the PP375 can be linked together using the other
supplied FFC.
STEP 1
Pre-install the requisite cables to their respective connector points on the DAC
Module as shown. Connect the FFC to the DAC Modules PP375 IN only if the
C375BEE has a PP375 already installed.
STEP 2
Make the following connections:
1 DC POWER connector from DAC Module to corresponding P216B in
C375BEEs main board.
2 FFC from DAC Module’s ANALOG OUT to P213B on C375BEEs main board.
3 If the optional PP375 module is installed: FFC from DAC Modules PP375 IN
to the corresponding FPC (exible printed circuit) connector of the PP375
module.
Ensure good harnessing by exing and safely contorting the FFC and
DCPOWER connectors.
STEP 3
Remove the dummy cover at the back of the C375BEE and install in its place the
DAC Module. Use the supplied screws to x into place the DAC Module.
3
2
1
IMPORTANT!
The DAC module is only compatible with C 375BEE units that have the
0.5Wstandby logo on their rear panels.
©2015 NAD ELECTRONICS INTERNATIONAL, A DIVISION OF LENBROOK INDUSTRIES LIMITED
All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited.
No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
MDCDAC_QS_V06  04/15
1
2
MOUNTING INSTRUCTION FOR THE C356BEE
The DAC Module is compatible with C356BEE. Using the supplied exible at
cable (FFC), DC power connector and screws, the DAC Module can be installed
in a C356BEE by undertaking the following procedure.
STEP 1
Pre-install the requisite cables to their respective connector points.
Connect the following
1 DC POWER connector from DAC Module to corresponding CB48 on
C356BEE’s main board.
2 FFC from DAC Module’s ANALOG OUT to CB36 on C356BEEs main board.
Ensure good harnessing by exing and safely contorting the FFC and DC POWER
connectors.
STEP 2
Remove the dummy cover at the back of the C356BEE and install in its place the
DAC Module. Use the supplied screws to x into place the DAC Module.


Product specificaties

Merk: NAD
Categorie: Niet gecategoriseerd
Model: MDC DAC 2.0

Heb je hulp nodig?

Als je hulp nodig hebt met NAD MDC DAC 2.0 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd NAD

NAD

NAD VM 300 Handleiding

28 Maart 2023
NAD

NAD VM 130 Handleiding

25 Februari 2023
NAD

NAD VM 310 Handleiding

18 Februari 2023
NAD

NAD MDC DAC 2.0 Handleiding

17 Februari 2023
NAD

NAD DAC 2 Handleiding

4 Februari 2023
NAD

NAD ВМ 130i Handleiding

17 Januari 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd