Mitsubishi PZ-70CSW-E Handleiding
Mitsubishi
Niet gecategoriseerd
PZ-70CSW-E
Bekijk gratis de handleiding van Mitsubishi PZ-70CSW-E (7 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 81 mensen en kreeg gemiddeld 4.7 sterren uit 41 reviews. Heb je een vraag over Mitsubishi PZ-70CSW-E of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/7
1
This CO
2 sensor changes the color of its LED light in accordance with the CO2 concentration within the room, optimizes the amount of airow, and thus
reduces the fresh air load.
■ This manual must be read both fully and carefully before commencing installation procedures; furthermore, the subsequent installation must be
performed correctly and safely in accordance with the instructions given.
■ After installation, ensure that this manual is given to the customer.
1. Safety Precautions
WARNING
Incorrect handling could cause serious injury or death.
- Never modify or repair by yourself.
If the product is modied or inappropriately repaired, electric shock, re, etc. could result. Contact your dealer for repair.
- Do not move or reinstall the product by yourself.
If it is installed improperly, electric shock, re, etc. could result. Contact your dealer or technical representative.
-Usethespeciedcablesforwiringandconnectthemsecurely.Holdthecablessoasnottoapplyexternalforceofthecablestothe
connector.
Improper connection could result in heat generation or re.
-Allelectricalworkmustbeperformedbyalicensedtechnician,accordingtolocalregulationsandtheinstructionsgiveninthisInstallation
manual.
-Installtheproductinarmandstableplacetowithstandtheproductweight.
If the strength is inadequate, the product could drop and cause an injury.
- EnsurethatinstallationworkisdonecorrectlyfollowingthisInstallationmanual.
If it is installed improperly, electric shock, re, etc. could result.
- Close the control cover after installation.
-Donotinstalltheproductinaplacewhereammablegasesmayleak.
If gas should leak or accumulate around the product, re or explosion could result.
- Do not use the product in special environments.
The product could be damaged if it is used in locations subject to large quantities of oil (including machine oil), steam, or sulde gas.
-Donotinstalltheunitinaplacewherethetemperaturerisesabove40˚C(104°F),wherelargeamountsofoil,steam,organicsolvents,or
corrosivegases,suchassulfuricgas,arepresent,orwhereacidic/alkalinesolutionsorspraysareusedfrequently.
These substances can compromise the performance of the unit or cause certain components of the unit to corrode, which can result in electric shock,
malfunctions, smoke, or re.
- Donotinstalltheproductinaplacewherehighlyhumid,likeabathroom,orotherwetplace.
It could cause electric shock or injury.
CAUTION
Incorrect handling could cause injury or damage to property or household eects.
- Wire so that it does not receive any tension.
Tension could cause wire breakage, heating or re.
-Sealthecablefromthesensorcasewithputtyetc.
Any dew, moisture, cockroaches, insects entering the unit could cause electric shock or malfunctions.
-Putonglovesduringinstallation.
Failure to do so could cause injury.
-Toavoiddiscoloration,donotusebenzene,thinner,ethanol,hypochlorousacidorchemicalragtocleanthecase.Tocleanthecase,wipe
withasoftclothsoakedinwaterwithmilddetergent,wipeothedetergentwithawetcloth,andwipeowaterwithadrycloth.
Lossnay CO2 Sensor Wall-Mounted Type
PZ-70CSW-E
Installation and Instruction Manual
2107876H65401
2
2.Outlinedrawings,IncludedAccessories,and
Specications
■ Includedaccessories
Please conrm that the following accessory parts are included in the box.
1. Sensor case (top case, bottom case): x 1
2. Cross-slot pan-head screws M4x30: x 2
3. Wood screws 4.1x16: x 2
4. CO2 sensor cable (10 m (11 yards)): x 1
*
1
5. LED cable (10 m (11 yards)): x 1
*
2
6. LED display explanation nameplate: x 1
7. Safety caution for installation: x 1
■ Specications
Rated power supply voltage: 12 VDC (Supplied from the Lossnay)
Power consumption: 2 W or less.
Accessary wire length : 10 m (11 yards) [Maximum length is 20 m (22 yards) with eld supply extension]
Usage environment: 0 to 40 ˚C (32 to 104 ˚F), 80 % RH or less. (No Cigarette Smoke or Sulfur and with no dew condensation)
Detection range: 300 to 2000 ppm
Measurement accuracy: ± (70 + 5% of measurement value) ppm
Weight: 1.1 kg
LOW (Green LED) : CO2 concentration is below the threshold (1500 ppm at factory setting)
MID (Orange LED) : CO2 concentration exceeds the threshold
HIGH (Red LED) : CO2 concentration exceeds the threshold for a long time (20 minutes at factory setting).
* 1: In the range of 0 ˚C (32 ˚F) or less, CO2 Sensor may not detect the correct CO2 Concentration.
* 2: Measures the CO2 concentration around the location where the CO2 sensor is installed. In addition, the measurement accuracy may vary depending
on the usage environment, installation conditions, etc. but this is not a malfunction.
3. Installation Method
3.1 Determine the installation location for the sensor case
Ensure that you adhere to the following points.
(1) Ensure clear space around the case as shown in the gure on the right, regardless of whether it is
installed using a switch box or on a wall.
(2) Source the following items locally.
- Putty
<Extraitemsrequiredifinstallingusingaswitchbox>
- Single-gang switch box
- Thin steel conduit
- Lock nut and bushing
Note:
- Direct sunlight sometimes cause the sensor case to discolor. Please be careful when
deciding the install position.
- Determine the sensor installation location only after checking with local laws and
regulations.
- Ensure that no objects are placed in the clear space around the sensor case to detect the
correct CO2 concentrations.
- Ensure a at surface is selected for the installation surface.
Cable access hole
■ Outlinedrawings
70(2 3/4) 26(1 1/32)
120(4 23/32)
83.5(3 9/32)
Unit: mm (inch)
*
1
*
2
30 (1 3/16)
30 (1 3/16)
120 (4 23/32)
30 (1 3/16)
Minimum required space
around the CO
2
sensor
Unit: mm (inch)
8
(5/16)
16
(
5/8
)
16
(
5/8
)
ø6
(
1/4OD
)
20
(
13/16
)
20
(
13/16
)
83.5±0.4
(
3
9/32±1/32
)
25
(
1
)
25
(
1
)
102
(
4
)
54
(
2 1/8
)
ø6
(
1/4OD
)
6
(
1/4
)
20
(
13/16
)
10
(
3/8
)
44
(
1 3/4
)
1.5(1/16)
or less
Unit: mm (inch)
Product specificaties
| Merk: | Mitsubishi |
| Categorie: | Niet gecategoriseerd |
| Model: | PZ-70CSW-E |
Heb je hulp nodig?
Als je hulp nodig hebt met Mitsubishi PZ-70CSW-E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Mitsubishi
24 Mei 2025
24 Mei 2025
24 Mei 2025
23 Mei 2025
15 Mei 2025
15 Mei 2025
21 Oktober 2024
17 Augustus 2024
17 Augustus 2024
17 Augustus 2024
Handleiding Niet gecategoriseerd
- Pentatech
- SALEX
- Texas Instruments
- TP Link
- MOZA
- Alpina
- Violectric
- 3 Legged Thing
- Ondis24
- Milestone Systems
- Shimbol
- Gutfels
- Gymrex
- Gossen Metrawatt
- AURALiC
Nieuwste handleidingen voor Niet gecategoriseerd
18 September 2025
18 September 2025
18 September 2025
18 September 2025
18 September 2025
18 September 2025
18 September 2025
17 September 2025
17 September 2025
17 September 2025