Mikrotik LHG Lite60 Handleiding

Bekijk gratis de handleiding van Mikrotik LHG Lite60 (3 pagina’s), behorend tot de categorie Router. Deze gids werd als nuttig beoordeeld door 9 mensen en kreeg gemiddeld 4.0 sterren uit 8 reviews. Heb je een vraag over Mikrotik LHG Lite60 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1.

2.

3.

4.

5.

LHG Lite60

The LHG Lite 60 is an outdoor wireless router with a built-in directional antenna that works in the 60GHz spectrum. It can be used as a CPE to connect to

MikroTik devices that work in 60GHz access point mode.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate

measures.

Assembly

Attach the two legs to the LHG case, then snap the assembled LHG unit to the grid in the appropriate locations. Fix the legs in place with two self thread

screws (Included, use Phillips screwdriver PH2). The package also contains a grounding cable connector and a precision alignment mount. Alignment

instructions available on the product page on .https://mikrotik.com/products/

Connecting

Open the ethernet door to connect an ethernet cable to the ethernet port, connect the other end of the ethernet cable to the included PoE injector

(LHG Lite60), or an 802.3af/at the power source (supported only by the LHG 60G model).

Plug the PoE injector into your network switch or ISP internet outlet.

Plug the included power supply into the PoE injector to start up the device.

For configuration purposes, set your computer IP configuration to static in the range of 192.168.88.0-254 (/24 or 255.255.255.0)

The default IP address of the unit is 192.168.88.1/24, open this address in your web browser to start the configuration. The username is admin

and there is no password .(or, for some models, check user and wireless passwords on the sticker)

The device is preconfigured as a w60g station, and all you need to do is select the AP to connect to and set a device password. You can do this in the

quickSET tab that is loaded by default. In case the IP connection is not available, Winbox can be used to connect to the MAC address of the device. We

recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and stability.

More information about using RouterOS and connecting to this device in our documentation: +https://mt.lv/help+

Powering

The LHG Lite60 only accepts 12-30 V power from Passive PoE injectors (one power supply and PoE injector are included). The LHG 60G accepts 12-57 V

802.3af/at powering and also Passive PoE. Both models can consume up to 5 W at maximum load.

Extension Slots and Ports

One ethernet (10/100 Mbit or Gigabit, depends on model), supporting automatic cross/straight cable correction (Auto MDI/X), so you can use

either straight or cross-over cables for connecting to other network devices.

One Integrated w60g interface with a built-in antenna.

Product specificaties