Miele W1 WCE330 Handleiding

Miele Wasmachine W1 WCE330

Lees hieronder de 📖 handleiding in het Nederlandse voor Miele W1 WCE330 (4 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
WCE 330 en - AU, NZ M.-Nr. 10 874 790/00
Before the first use Operating the washing machine Preparing the laundry Selecting a programme Adding detergent Starting the programme Extras
OPERATING THE WASHING MACHINE
PREPARING THE LAUNDRY/SELECTING A PROGRAMME
ADDING DETERGENT/STARTING THE PROGRAMME
3
1 2
4
ɉBefore using the machine for the first
time, ensure that it is correctly installed
and connected.
Please read the separate operating
instructions supplied with the appliance.
ɉFailure to remove the transit bars can
result in damage to the washing machine
and to adjacent cabinetry or appliances.
Remove the transit bars as described in
"Installation and connection".
Switching on the washing machine
ĺTurn the programme selector to the
Cottons programme.
The welcome tone will sound and the
welcome screen will light up.
The display will guide you through the initial
commissioning process, which is divided
into 3steps.
For further information, please refer to the
separate operating instructions.
Operating the sensor controls
The sensor controls react to fingertip
contact. Selection is possible as long as the
respective sensor is illuminated.
If a sensor is brightly lit, this means:
currently selected
If a sensor is dimly lit, this means: selection
possible
Washing environmentally and economically
–To get the most out of your machine,
load the maximum dry load for the
programme you are using.
–When smaller amounts of laundry are
washed, the automatic load recognition
system will reduce the amount of water
and energy used.
–Use the programme for Express 20
small, lightly soiled loads.
–Modern detergents enable washing at
reduced temperatures (e.g. 20°C). Use
appropriate temperature settings for
saving energy.
–Reduce the amount of detergent with
smaller loads (approx. ⅓ less than the
amount recommended can be used
when washing a half load).
–Selecting the highest possible spin
speed for the wash programme will
save energy when drying in a tumble
dryer afterwards.
1. Preparing the laundry
ĺEmpty all pockets.
ɉForeign objects (e.g. nails,
coins, paper clips, etc.) can
cause damage to garments and
components in the machine.
ĺSort the laundry by colour and by care label. Most
garments have a textile care label in the collar or side
seam.
ĺPre-treat stains and badly soiled areas (see the booklet
"Miele's guide to laundry care").
1 Detergent dispenser drawer
2 Control panel
3 Access to drain filter, drain pump
and emergency release
4 Door
3. Loading the washing machine
Opening the door
ĺReach under the door grip and
pull the door open.
ĺUnfold the laundry and load
loosely in the drum.
Closing the door
ĺMake sure that no items are
caught between the door and
the seal.
ĺShut the door with a gentle
swing.
CapDosing
Three different types of capsule are
available:
Fabric care (e.g. fabric softener)
Additives (e.g. detergent enhancers)
Detergent
Each capsule contains the correct amount
for one wash cycle.
Capsules are available to order from Miele
or from the Miele online shop (see the end
of this booklet for contact details).
Keep capsules out of the reach of
children.
Activating CapDosing
ĺTouch the sensor.
The following appears in the display:
No cap 
ĺTouch the sensors until the capsule 
you want appears in the display.
ĺConfirm the capsule with the sensor.OK
See "Detergent" in the operating
instructions for more information.
5. Adding detergent
Any detergent suitable for automatic front
loading washing machines can be used
with this appliance. Please observe the
instructions for use and dosage on the
detergent packaging.
There are several options for adding
detergent.
Filling with detergent
ĺPull out the
detergent drawer
and add
detergent to the
compartments.
Detergent for the pre-wash
Detergent for the main wash,
including Soak if selected
 / Fabric softener, liquid starch or
capsules
Adding fabric softener
ĺAdd fabric
softener or liquid
starch to the
compartment.
Do not exceed
the maximum
level mark.
It will be automatically dispensed in the
final rinse. At the end of the programme a
small amount of water remains in the fabric
softener compartment.
Using detergent tablets or pods
Always put detergent tablets or pods
directly in the drum with the laundry.
They cannot be added via the detergent
dispenser drawer.
PowerWash display with the Quick and
Eco sensor controls
PowerWash display
Normal programme sequence.
ĺDo not activate the or Quick Eco
sensors.
Quick sensor
Short programme sequence. The
mechanical action and energy will increase
with this option.
ĺTouch the sensor.Quick
Eco sensor
Energy-saving programme sequence.
The wash temperature is reduced and the
programme duration increased.
ĺTouch the sensor.Eco
Delay start
Delay start
With Delay start you can delay the start of
the programme. The start of the programme
can be delayed from 15minutes up to a
maximum of 24hours.
4. Selecting programme settings
Selecting a temperature/spin speed
ĺTouch the sensors above or below the temperature 
or spin speed value in the display until the temperature/
spin speed you want appears in the display.
Selecting Extras
There are two ways of selecting Extras.
1. Directly above the sensor controls
ĺTouch the sensor for the Extra you want. It then lights up
brightly.
2. Via the Extras sensor control and the display
ĺTouch the sensor control.Extras
The following appears in the display: No Extras
ĺTouch the sensor controls until the Extra you want 
appears in the display and confirm this with the OK
sensor.
2. Selecting a programme
ĺTurn the programme selector to a programme.
Programme selection
There are two possible ways to select a programme:
1. Selecting standard programmes via the
programme selector
ĺTurn the programme selector to the required
programme.
The selected programme will appear in the display. This
will then be replaced by the standard display.
2. Selecting further programmes via the "Further
programmes/ position and the display"
ĺTurn the programme selector to the Further
programmes/ position.
The following appears in the display: Express 20
ĺTouch the sensors until the programme you want 
appears in the display.
ĺConfirm the programme with the sensor.OK
1 Control panel
The control panel consists of a display
and various sensor controls.
2 Display
The following values are shown and/or
selected in the display:
3 Sensor controls  
The values in the display can be
changed with the . sensors
4 OK sensor
The OK sensor is used to confirm
selected values.
5 PowerWash display with the Quick
and Eco sensors
If the PowerWash indicator lights up
when you select a wash programme,
you can choose between three
programme sequences.
6 Optical interface
for service technicians.
7 Sensor controls for Extras
You can supplement wash programmes
with Extras.
8   sensor 
Activates detergent dispensing with a
capsule.
9  sensor
The sensor button starts the Delay  
start function.
10 Start/Stop sensor
Touching the Start/Stop sensor starts
the selected programme or cancels a
programme that has already started.
11 Programme selector
For selecting programmes and switching
the washing machine off.
6. Starting the programme - end
of the programme
Starting the programme
ĺTouch the flashing sensor.Start/Stop
The door will lock ( appears in the display)
and the programme will start.
At the end of the programme
The door is still locked during the Anti-
crease phase and the following will appear
alternately in the display:
  Finish/Anti-crease and
 Press Start/Stop
ĺTouch the sensor. The door Start/Stop
will be unlocked.
ĺPull open the door.
ĺRemove the laundry.
Check that all items have been removed
from the drum.
ĺCheck the folds
in the door seal
for any small
articles, e.g.
buttons, which
might be lodged
there.
ĺTurn the programme selector to the
position. This switches the washing
machine off.
ĺIf applicable, remove the used capsule
from the detergent dispenser drawer.
Close the door. Otherwise there is
a danger of objects being placed
inadvertently in the drum. If these remain
unnoticed and were washed in the next
load, they could damage the laundry. An
open door is also a danger to pets and
children.
Extras
You can use the Extras sensor to augment
the wash programmes.
SingleWash
For efficiently washing a very small load
(<1kg) in a normal wash programme. The
wash duration is reduced.
Please note the following advice:
–Use liquid detergent
–Reduce the dosage to a maximum of
50% of the amount quoted for a ½ load
Pre-ironing
In order to reduce creasing, the laundry
undergoes a smoothing process at the
end of the programme. Reducing the
maximum load by 50% will give a better
result. Follow the instructions in the
display. Small loads give a better result.
The garments must be suitable for drying
in a tumble dryer and suitable for  
ironing  .
Water +
The water level in the wash and rinse
stages is increased and a second rinse is
carried out in the "Separate rinse/Starch"
programme.
You can select other functions for the
Water + sensor control. These are
described in "Settings".
Pre-wash
For laundry with large amounts of dirt, e.g.
dust and sand.
Soak
For heavily soiled and stained items with
protein stains.
A duration of between 30minutes
and 6hours can be chosen for the
soak process. See "Settings" for more
information.
The factory default setting is 30minutes.
Intensive
For hard-wearing laundry that is very
heavily soiled. Cleaning efficiency
is increased through more intense
mechanical action and the application of
more heat energy.
Extra quiet
This option reduces noise levels during
the wash programme. Use this if you
want to wash during quiet periods (for
instance, when children are sleeping). The
final spin is automatically reduced to
(Rinse hold). The programme duration is
increased.
Extra gentle
Drum rotation and wash duration are
reduced. Lightly soiled fabrics are washed
more gently.
AllergoWash
This option should be used where high
standards of hygiene are required. More
energy is used to lengthen temperature
holding times and more water is used to
increase rinsing efficiency. The items must
be suitable for drying in a tumble dryer
 . and suitable for ironing
en - AU, NZ M.-Nr. 10 874 790
Cleaning and careProgramme chart Detergent Problem solving guide
PROGRAMME CHART
CLEANING AND CARE
PROBLEM SOLVING GUIDE
Quick Start Guide
Washing machine
These short instructions are not a substitute for the operating instructions supplied with
the appliance. Please read the operating instructions supplied with your washing machine
before using it for the first time and take note of the Warning and Safety instructions, as
well as the full descriptions on how to use your appliance.
Programme
Load
(inkg) Temperature Items Extras
Cottons 8.0 Cold to 90°C Cottons, linens or cotton mix fabrics, e.g. table linen, towelling, underwear,
T-shirts etc.
, , , ,
, , , ,
Minimum iron 4.0 Cold to 60°C Synthetic, mixed fibre and easy care cotton. , , , ,
, , , ,
Delicates 3.0 Cold to 60°C Delicate garments made from synthetic fibre, mixed fibre, rayon and
viscose.
, , , ,
, , , 
Woollens 2.0 Cold to 40°C Machine-washable or hand-washable wool or wool blend fabric. If the care
label does not specify a temperature, wash using the cold setting.
, 
Silks 1.0 Cold to 30°C Silks and other hand-washable fabrics with no wool content, e.g. satin,
lace and silk.
, 
Shirts 1.0⁄2.0 Cold to 60°C Shirts and blouses made of cotton and mixed fibre.
If the preset Pre-ironingoption is switched off, the maximum load capacity
is increased to 2.0kg.
, , , ,
, , , 
QuickPowerWash 5.0 40°C – 60°C Moderately soiled garments which are also suitable for washing in the
Cottons programme.
, 
Dark garments/
Denim
3.0 Cold to 60°C Black and dark garments made from cotton, mixed fibres and denim. , , , ,
, , , 
Outerwear 2.5 Cold to 40°C Performance outerwear (e.g. jackets and trousers) made from membrane
fabric such as Gore-Tex®, SYMPATEX®, WINDSTOPPER® etc.
, , , ,
Proofing 2.5 40°C Treating microfibre fabric, skiwear and table linen made from mainly
synthetic fibres to provide a water and dirt resistant finish.
–
Drain/Spin 8.0 – Drain only: Select for the spin speed.0 rpm –
Express 20 3.5 Cold to 40°C Cotton garments that have hardly been worn or are only very lightly soiled.
Sportswear 3.0 Cold to 60°C Sportswear such as jersey shirts and leggings, and microfibre and fleece
garments.
, , , ,
, , 
Automatic plus 6.0 Cold to 40°C Mixed loads of garments sorted according to colour which are suitable for
the and programmes.Cottons Minimum iron
, , , ,
, , , 
Separate rinse/
Starch
8.0 – For rinsing items washed by hand.
Starching table cloths, serviettes and workwear.
, 
Clean machine No
load
85°C With frequent washing at low temperatures there is a danger of a build-up
of bacteria in the washing machine.
Cleaning the washing machine will significantly reduce bacteria, mould,
and biofilm, and prevent the build-up of unpleasant odours.
–
  = SingleWash; = Pre-ironing; = Water+, = Pre-wash; = Soak; = Intensive; = Extra quiet; = Extra gentle; = AllergoWash
Miele recommended detergents
Programmes
Miele
UltraWhite
Miele
UltraColor
Miele
Cap
Miele
Cap
Miele
Cap
Cottons   –
Minimum iron ––
Delicates –  –
Woollens – – – –
Silks – – – –
Shirts   –
QuickPowerWash   –––
Dark garments/
Denim
–– –
Outerwear – – –––
Proofing – – – –
Express 20 –– –
Sportswear – – – –
Automatic plus ––
Separate rinse/
Starch
–/– –/– –/– –/–/–
= Recommended; – = Not recommended
  = Sportswear; = Down Items; = WoolCare, = Fabric Softener; = Booster 
Cleaning the drum (Hygiene info)
Washing at low temperatures and/or using
liquid detergents can cause bacteria and
odours to build up in the washing machine.
Use the Clean machine programme to
clean the machine. Note the message in the
display:.
 Hygiene info:
Run a programme at min.
75°C or "Clean machine"
Cleaning the detergent dispenser
drawer
Washing at low temperatures and the use
of liquid detergent can lead to a build-up
of mould and bacteria in the detergent
dispenser drawer.
ĺFor hygiene reasons, clean the entire
drawer at regular intervals.
ĺPull out the
detergent
dispenser drawer
until a resistance
is felt.
ĺPress down the release button and, at
the same time, pull the drawer right out of
the machine.
ĺClean the detergent drawer with warm
water.
Cleaning the siphon tube and the fabric
softener channel
ĺPull the siphon
out of the
compartment
and clean it
under warm
running water.
ĺClean the siphon tube in the same way.
ĺRefit the siphon.
ĺClean the fabric
softener channel
using a brush
and warm water.
ɉLiquid starch can cause the siphon
to become clogged. Make sure that
you clean the siphon and siphon tube
particularly thoroughly after using liquid
starch a few times.
Cleaning the detergent dispenser
drawer housing
ĺUse a bottle brush to remove detergent
residues and limescale from the jets
inside the detergent dispenser drawer
housing.
Some of the messages in the display are more than one line long. Touch the or sensor  
to read them in full.
Message Possible cause and remedy
The control panel
remains dark.
There is no power to the machine.
ĺCheck whether the mains plug is plugged in and switched on.
ĺCheck whether the circuit breaker has tripped.
The washing machine has switched off automatically to save
energy.
ĺSwitch the washing machine on again by turning the programme
selector.
 Door lock. 
Service
The door is not closed properly. The door lock could not engage.
ĺClose the door again.
ĺStart the programme again. If the fault message appears again,
contact Miele.
 Check drainage.
See
The water outlet is blocked or restricted. The drain hose has been
fixed too high.
ĺClean the drain filter and the pump.
ĺCheck whether the maximum delivery head of 1m has been
exceeded.
 Water intake. See
The water inlet is blocked or restricted.
ĺCheck whether the tap is turned on properly.
ĺCheck whether the inlet hose is kinked.
ĺCheck whether there is sufficient water pressure.
The filter in the water inlet is blocked.
ĺClean the filter (see the operating instructions).
  Service.
Waterproof syst. Turn
off 
The water protection system has reacted.
ĺTurn off the tap.
ĺCall Miele.
  Service. Fault F There is a fault.
ĺDisconnect the washing machine from the mains electricity
supply, either by switching it off at the wall socket and
withdrawing the plug, or by disconnecting it at the circuit
breaker.
ĺWait before reconnecting the washing at least 2 minutes
machine to the mains electricity supply.
ĺThen switch the washing machine on again.
ĺRestart the programme.
If the fault message appears again, contact Miele.
 Door jammed.
Service.
The door lock has jammed.
ĺCall Miele.
Message Possible cause and remedy
 Check detergent Excessive foam has built up during washing.
ĺCheck the amount of detergent dispensed.
ĺObserve the instructions on the detergent packaging and the
degree of soiling of the laundry.
ĺIf necessary, reduce the dosage amount by increments of 10%.
 Hygiene info:
Run a programme at
min.
75°C or "Clean
machine" programme
A programme using a temperature above 60°C has not been run
for a long time.
ĺTurn the programme selector to Further programmes/
and select the programme in the Clean machine Maintenance
submenu.
ĺRun the programme using the Miele IntenseClean Clean Machine
machine cleaner or a universal powder detergent.
This will clean the washing machine and prevent a build-up of
bacteria and odours.
 Align the washing
machine
The Extra which runs at the end of the programme Pre-ironing
could not be carried out properly.
ĺCheck whether the washing machine is aligned correctly
as described in "Installation and connection – Levelling the
machine".
ĺCheck whether the maximum delivery head of 1m has been
exceeded.
If the fault message appears again, contact Miele. The washing
machine can still be used, however without the Extra.Pre-ironing
 Check filter + jet The pumps are dirty.
ĺClean the pumps as described in "Problem solving guide -
Opening the door in the event of a blocked drain outlet and/or
power cut".
ĺStart the programme again after cleaning.
The jet in the top of the door ring is blocked with fluff.
ĺRemove the fluff with your finger. Do not use any sharp or
pointed tools to do this.
ĺStart the programme again after cleaning.
If the fault message appears again, contact Miele. The washing
machine can still be used but with reduced functionality.
The messages will appear at the end of the programme and when the washing machine is
switched on and need to be confirmed with the sensor.OK

Product specificaties

Merk: Miele
Categorie: Wasmachine
Model: W1 WCE330

Heb je hulp nodig?

Als je hulp nodig hebt met Miele W1 WCE330 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Wasmachine Miele

Miele

Miele WXD 160 WCS W1 Handleiding

9 April 2024
Miele

Miele WXI 860 WCS W1 Handleiding

9 April 2024
Miele

Miele WXR 860 WCS W1 Handleiding

9 April 2024
Miele

Miele W 2819 i WPM L Handleiding

8 April 2024
Miele

Miele WEK375 WPS PWash&10kg Handleiding

4 Maart 2024
Miele

Miele WWB380 WCS 125 Edition Handleiding

4 Maart 2024
Miele

Miele WEB695 WPS 125 Edition Handleiding

4 Maart 2024
Miele

Miele WSK363 WCS Handleiding

4 Maart 2024
Miele

Miele WSB383 WCS 125 Edition Handleiding

4 Maart 2024
Miele

Miele WCI890 WCS 125 Gala Edition Handleiding

4 Maart 2024

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Winia

Winia WVD-A08T1WK14B Handleiding

28 April 2024
Continental Edison

Continental Edison CELL7140IB Handleiding

28 April 2024
Bauknecht

Bauknecht WAT Smart Eco 12C Handleiding

27 April 2024
Bauknecht

Bauknecht B7 89 SILENCE EE Handleiding

27 April 2024
BEKO

BEKO WTE 7512 BSS Handleiding

26 April 2024
MPM

MPM -4610-PH-04 Handleiding

25 April 2024
Samsung

Samsung WW11DB8B95GH Handleiding

25 April 2024
Sôlt

Sôlt GGSFLW800W Handleiding

22 April 2024
Whirlpool

Whirlpool ZEN FSCR70421 Handleiding

21 April 2024
Samsung

Samsung WW90T4540TE Handleiding

18 April 2024