Microchip USB2230 Handleiding

Microchip Niet gecategoriseerd USB2230

Lees hieronder de 📖 handleiding in het Nederlandse voor Microchip USB2230 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
SMSC AN 14.18 APPLICATION NOTE Revision 0.96 (06-01-06)
AN 14.18
Design Guidelines for
USB22XX/USB260X
High-Speed SD
1 Introduction
This application note provides information on Printed Circuit Board layout for High-Speed Secure-Digital
(SD) media sockets with USB22XX and USB260X.
2 Overview
Successful High-Speed operation of Secure-Digital media with USB22XX and USB260X requires
special consideration for Printed Circuit Board (PCB) layout. This application note describes the
important items to consider for layout of PCB.
3 PCB Layout Guidelines
The guidelines presented are applicable to all SMSC card-reader products that support High-Speed
Secure-Digital operation. Guidelines for both two-layer and four-layer PCBs are presented here.
3.1 Power and Ground Distribution to SD Socket
Ground connection between the card-reader and the media socket is important, both for supply return
current and signal return currents. The ground should be solid, have low impedance and few
constrictions between the card-reader and the socket. The card-reader supplies the power to the socket
in most applications since the power-FET is built-in to the SMSC card-reader.
îš„SD socket VDD supply trace from card-reader should be 20 mils wide, 0.5 oz or thicker for a length
up to 3000 mils.
îš„SD socket ground connection: plane, 0.5 oz or thicker, between socket and card-reader.
Note: No constrictions or cuts allowed in the ground between card-reader and socket.
3.2 Signal Traces to SD Socket
The Secure-Digital interface has a total of seven signals to the card-reader. Six of these signals are
critical for high-speed operation: SD_DAT[0:3], SD_CMD and SD_CLK and require special
considerations.
îš„Signal traces must be above a solid and continuous ground plane along the path from card-reader
to socket.
îš„SD_CLK trace requires two grounded guard-traces, one on each side spaced, at 3 times minimum
spacing.
îš„SD_CLK guard traces must have a via connecting to the ground plane at both ends and every 500
mils along the path.
Design Guidelines for USB22XX/USB260X High-Speed SD
Revision 0.96 (06-01-06) 2 SMSC AN 14.18
APPLICATION NOTE
îš„SD_CLK termination resistor must be placed close, within 400 mils to the SD_CLK pin on card-
reader for two layers PCB.
îš„SD_CLK termination resistor must be placed close, within 400 mils to socket for four layers PCB.
îš„SD_CLK must be buffered when trace length exceeds 1000 mils. A 74AHC1G125 or equivalent
buffer can be used that has less than 2.5 ns propagation delay.
3.3 Signal Trace Length
Trace length for SD signals must be less than the maximum length specified in Table 3.1 and Table 3.2.
An external buffer is required for SD_CLK when trace lengths exceed 1000 mils (800 mils excluding
the socket itself). Table 3.1 provides the trace length when the unbuffered SD_CLK is driven directly
by the SMSC card-reader. Table 3.2 provides the trace length when an external clock buffer is used.
the buffer must be connected with a trace shorter than 50 mils to the card-reader SD_CLK pin. Skew
control between data lines is not critical within the limits given in the tables.
Figure 4.1 Figure 4.2 and show the suggested placement of a series termination resistor. Figure 4.3
shows the series termination resistor when an external buffer is used with a long SD_CLK trace. The
details for guarding of the SD_CLK are shown in Figure 5.1.
Note: Trace length includes 200 mils for trace inside the socket.
Table 3.1 Trace length and tolerance for unbuffered SD_CLK
Signal
Maximum
Trace Length
(including
socket) [mils]
PCB Trace
Impedance 2-
layer PCB
[Ohm]
PCB Trace
Impedance 4-
layer PCB
[Ohm]
Trace Length
Tolerance
[mils]
Maximum
Trace Length
difference to
SD_CLK [mils]
SD_CLK 1000 100 - 130 > 55 N/A N/A
SD_DAT[0:3] 2500 80 - 150 > 50 +/- 750 -250 to +1500
SD_CMD 2500 80 - 150 > 50 N/A -250 to + 1500
Table 3.2 Trace length and tolerance for buffered SD_CLK
Signal
Maximum
Trace Length
(including
socket) [mils]
PCB Trace
Impedance 2-
layer PCB
[Ohm]
PCB Trace
Impedance 4-
layer PCB
[Ohm]
Trace Length
Tolerance
[mils]
Maximum
Trace Length
difference to
SD_CLK [mils]
SD_CLK 3000 80 - 150 > 55 N/A N/A
SD_DAT[0:3] 3500 80 - 150 > 50 +/- 750 -500 to +500
SD_CMD 3500 80 - 150 > 50 N/A -500 to +500
Design Guidelines for USB22XX/USB260X High-Speed SD
SMSC AN 14.18 3 Revision 0.96 (06-01-06)
APPLICATION NOTE
4 Placement of Series Termination Resistor and Buffer
Figure 4.1 Place series termination resistor close to card-reader pin SD_CLK for two layer PCBs.
Figure 4.2 Place series termination resistor close to media socket pin SD_CLK for four layer PCBs.
Figure 4.3 Place buffer and series termination resistor close to card reader pin SD_CLK when SD_CLK trace
is longer than 800 mils not including the socket.

Product specificaties

Merk: Microchip
Categorie: Niet gecategoriseerd
Model: USB2230

Heb je hulp nodig?

Als je hulp nodig hebt met Microchip USB2230 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Microchip

Microchip

Microchip AT32UC3A3256 Handleiding

10 April 2024
Microchip

Microchip AT32UC3A364 Handleiding

10 April 2024
Microchip

Microchip AT32UC3B0256 Handleiding

10 April 2024
Microchip

Microchip AT32UC3A0512 Handleiding

10 April 2024
Microchip

Microchip AR1010 Handleiding

10 April 2024
Microchip

Microchip AT32UC3C0256C Handleiding

10 April 2024
Microchip

Microchip AT32UC3A364S Handleiding

10 April 2024
Microchip

Microchip AT32UC3C1256C Handleiding

10 April 2024
Microchip

Microchip AT32UC3A1128 Handleiding

10 April 2024
Microchip

Microchip AR1100BRD Handleiding

10 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024