Microchip MIC5018 Handleiding

Bekijk gratis de handleiding van Microchip MIC5018 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 129 mensen en kreeg gemiddeld 4.7 sterren uit 5 reviews. Heb je een vraag over Microchip MIC5018 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

January 19961MIC5018 Evaluation Board

MIC5018 Evaluation Board

IttyBitty™ High-Side MOSFET Driver

Description

The MIC5018 evaluation board is an assembled, high-side

switch for 2.7V to 9V power-switching applications.

Requirements

The MIC5018 evaluation board requires a power supply,

load, and logic output.

Operation

Connect the evaluation board as shown. A function genera-

tor with a TTL output, or a logic-level, square wave output, can

be used as a control signal. On/o power switch operation

can be simulated by setting the output frequency to about 1Hz

or 2Hz.

Applying logic high to the control input will energize the load;

logic low will de-energize the load.

The MIC5018 makes it possible to switch a supply as low as

2.7V using a logic-level MOSFET such as the IRL3103.

Because the IRL3103 also has a 20V maximum gate±

voltage rating, the MIC5018 evaluation board can switch a 5V

logic supply or higher voltage circuit without an additional

gate-to-source clamping zener. (Logic-level MOSFET gates

are usually rated at 10V maximum. See “MOSFET Selec-±

tion” in the MIC5018 data sheet for more information.)

Supply Precautions

The MIC5018 evaluation board includes a tantalum bypass

capacitor on the supply input. Always apply power using the

power supply’s on/o switch. Avoid applying power by

connecting the supply input to an operating power supply.

Applying power instantaneously to any tantalum capacitor

may cause capacitor failure.

Wiring

+–

Load

2.7V to 9V Supply

TTL

Control Logic

Your load here

or try a

100 1/4WΩ

resistor

MIC5018 Evaluation Board Wiring

MICREL INC.1849 FORTUNE DRIVESAN JOSE, CA 95131USATEL + 1 (408) 944-0800FAX + 1 (408) 944-0970

Bill of Materials

Item Qty.Description

—1Micrel, MIC5018BM4

IttyBitty™ high-side MOSFET driver

C11AVX, TAJB475M020 Note 1

4.7µF 20V tantalum

Q11International Rectifier, IRL3103 Note 2

14mΩ N-channel power MOSFET

Note 1:See “Operation: Supply Precautions” for information on safely

using tantalum capacitors.

Note 2:Manufacturer’s preliminary data sheet ratings:

14mΩ at VGS = 10V, ID = 34A, TJ = 25°C;

19m at VΩGS = 4.5V, ID = 28A, TJ

= 25C.°

The gate features logic-level performance with 20V maximum±

rating. Heat sinking is required at higher currents.

Load Precautions

A 100, 1/4W resistor can be used as a low-current demon-Ω

stration load. When switching other loads, always stay within

the current rating of the MOSFET and power supply. See

Note 2, above.

The evaluation board MOSFET is located near the edge of

the board so that it can be fastened to a at heat sink.

Inductive loads require a Schottky diode to control the induc-

tive kick that occurs upon turno. Refer to the MIC5018 data

sheet for a connection example. At high current, leads to a

resistive load may also exhibit enough inductance to cause

signicant inductive kick.

Product specificaties