Microchip MIC22705YML Handleiding

Microchip Niet gecategoriseerd MIC22705YML

Lees hieronder de 📖 handleiding in het Nederlandse voor Microchip MIC22705YML (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/9
MIC22705YML EV
Evaluation Board
1MHz, 7A Integrated Switch High-
Efficiency Synchronous Buck Regulator
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (
408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
February 2011 M9999-020411-A
General Description
The Micrel MIC22705 is a high-efficiency, 7A, integrated
switch, synchronous buck (step-down) regulator. The
MIC22705 achieves more than 95% efficiency and
switches at 1MHz. The ultra-high speed control loop keeps
the output voltage within regulation even under the
extreme transient load swings commonly found in FPGAs
and low-voltage ASICs. The output voltage is pre-bias safe
and is adjustable down to 0.7V.
The MIC22705 offers a full range of sequencing and
tracking options. The Enable/Delay (EN/DLY) and Power
Good (PG) inputs allow versatile turn-on and turn-off
sequencing across multiple devices. The Ramp Controlâ„¢
(RC) input allows start-up voltage tracking, either directly
or ratio-metrically.
The MIC22705 is available in a 24-pin 4mm x 4mm MLF®
with a junction operating range from –40° °C to +125 C.
Data sheets and support documentation are found on the
Micrel web site: www.micrel.com.
Requirements
The MIC22705YML EV requires a power supply of 2.9V to
5.5V, and a test load. Ensure that the power supply can
provide the wattage required for the chosen test load. The
load can be active (electronic load) or passive (resistor).
Additionally, monitor the Power Good output (PG) with a
multimeter or an oscilloscope if desired.
Precautions
There is no reverse input protection on this board. When
connecting supplies and signals ensure that correct
polarities are observed.
Getting Started
1. VIN Supplies
Connect the VIN supply (2.9V to 5.5V) across the PVIN and
PGND terminals. Monitor VIN at the PVIN and PGND
terminals with a voltmeter.
2. Enable/SHDN Inputs
The enable input EN is internally pulled up with a 1µA
current source. When external on/off control is desired,
install Q1 and R5, and connect a logic level control signal
to the SHDN input. When SHDN is high, the output is off,
and when SHDN is low, the output is on.
3. Monitor Outputs
Monitor the output VOUT with a scope or DVM connected
across the VOUT and PGND terminals.
4. Output Load
Connect a load across the VOUT and PGND terminals.
Use an active or passive load.
5. Turn On the Power
Turn on the power supply and verify that VOUT = 1.8V.
Ordering Information
Part Number Description
MIC22705YML EV Evaluation Board for the MIC22705YML
Micrel, Inc. MIC22705 Evaluation Board
February 2011 2 M9999-020411-A
EV Board Features
See the MIC22705YML datasheet for detailed
explanations of these functions.
Enable/Delay (EN/DLY)
Enable/Delay allows delayed turn on of the MIC22705.
Install a capacitor in location C6 to increase the start-up
delay of the MIC22705.
Shutdown Input (SHDN)
SHDN allows enable/disable of the MIC22705 with an
external logic signal. To activate the shutdown feature,
install components into the locations labeled Q1 and R5
(component recommendations are listed in the Bill of
Materials later in this document). With the components
installed, force SHDN high to disable the MIC22705, and
low to allow the MIC22705 to operate normally.
Delay (DELAY)
DELAY allows a delayed Power Good output (PG)
indication. Install a capacitor in location C8 to increase the
Power Good delay timing of the MIC22705.
Ramp Control (RC)
Ramp control allows slowing the slew rate of the
MIC22705 output. Increase the value of capacitor C7 to
reduce the slew rate.
Power Good Output (PG)
Open drain output PG pulls low when the output voltage of
the MIC22705 is out of specification. PG is pulled up to VIN
by a 47.5kΩ resistor.
Switch Voltage (VSW)
Test point VSW is provided to monitor the internal switching
node. VSW is isolated from the switch node by 49.9Ω
resistor R6.
Micrel, Inc. MIC22705 Evaluation Board
February 2011 3 M9999-020411-A
Typical Characteristics
Efficiency (V
IN
= 3.3V)
vs. Output Current
70
75
80
85
90
95
100
0123456789
OUTPUT CURRENT (A)
EFFICIENCY (%)
2.5V
1.8V
1.5V
1.2V
1.0V
0.9V
0.8V
V
IN
= 3.3V
IC Power Dissipation vs. Output
Current (VIN = 3.3V)
0
0.5
1
1.5
2
0246
OUTPUT CURRENT (A)
POWER DISSIPATION (W)
VIN = 3.3V
VOUT = 0.8V, 1.0V, 1.2V, 1.5V, 1.8V, 2.5V

Product specificaties

Merk: Microchip
Categorie: Niet gecategoriseerd
Model: MIC22705YML

Heb je hulp nodig?

Als je hulp nodig hebt met Microchip MIC22705YML stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Microchip

Microchip

Microchip AT32UC3A3256 Handleiding

10 April 2024
Microchip

Microchip AT32UC3A364 Handleiding

10 April 2024
Microchip

Microchip AT32UC3B0256 Handleiding

10 April 2024
Microchip

Microchip AT32UC3A0512 Handleiding

10 April 2024
Microchip

Microchip AR1010 Handleiding

10 April 2024
Microchip

Microchip AT32UC3C0256C Handleiding

10 April 2024
Microchip

Microchip AT32UC3A364S Handleiding

10 April 2024
Microchip

Microchip AT32UC3C1256C Handleiding

10 April 2024
Microchip

Microchip AT32UC3A1128 Handleiding

10 April 2024
Microchip

Microchip AR1100BRD Handleiding

10 April 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024