Metra Axxess AX-ADFD02 Handleiding
Metra
Niet gecategoriseerd
Axxess AX-ADFD02
Bekijk gratis de handleiding van Metra Axxess AX-ADFD02 (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 67 mensen en kreeg gemiddeld 4.9 sterren uit 34 reviews. Heb je een vraag over Metra Axxess AX-ADFD02 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
AX-ADFD02
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 6/27/18 INSTAX-ADFD02
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
INTERFACE FEATURES
INTRODUCTION
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors or solder gun,
solder, and heat shrink • Wire cutter • Zip ties
TABLE OF CONTENTS
Connections to be made ....................................... 3
Installing & programming the AX-ADFD02
AX-ADBOX1 ...........................................................4
AX-ADBOX2 ..........................................................5
Extra features .........................................................6
Ford Data Interface 2011-up*
APPLICATIONS
See inside front cover
• Provides accessory power (12-volt 10-amp)
• Maintains the retained accessory power (R.A.P.) feature
• Provides NAV outputs (parking brake, reverse, speed sense)
• Retains SYNC
• Retains the factory AUX-IN jack
• Pre-wired ASWC-1 harness (ASWC-1 sold separately)
• Designed for non-amplified models
• Retains balance and fade
• Micro “B” USB updatable
The AX-ADFD02 harness is designed for, and must be used with, the
AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the
AX-ADBOX1 or AX-ADBOX2 for the 16-pin connector with stripped leads.
• AX-ADFD02 harness
*Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
2
APPLICATIONS
FORD
Escape † 2013-up
F-250/350/450/550 XL (without CD player) †
2017-up
Fiesta † 2014-up
Fiesta (with SYNC) 2011-2013
Focus 2012-2014
Transit † 2015-up
Transit Connect † 2014-up
† With AM/FM/CD radio
3
REV. 6/27/2018 INSTAX-ADFD02
CONNECTIONS TO BE MADE
From the 16-pin harness with stripped leads to the aftermarket radio (harness included with interface):
• Connect the wire to the accessory wire.Red
If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) Note: Red
wires on the AX-ADFD02 harness as well.
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
•
If the aftermarket radio has a mute wire and the vehicle is equipped with SYNC, connect the
Brown wire to it. If the mute wire is not connected, the radio will turn off when SYNC is activated
.
• Connect the wire to the right front positive speaker output.Gray
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the wire to the VSS/speed sense wire.Blue/Pink
• Connect the wire to the reverse wire.Green/Purple
• Connect the Light Green wire to the parking brake wire
• Tape off and disregard the following (5) wires, they will not be used in this application:
Blue/White Green Green/Black Purple Purple/Black, , , ,
From the AX-ADFD02 harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the battery wire.
• If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) wires to Red
accessory power.
• Connect the wire to the power antenna wire.Blue
• Connect the wire to the left rear positive speaker output.Green
• Connect the wire to the left rear negative speaker output.Green/Black
• Connect the wire to the right rear positive speaker output.Purple
• Connect the wire to the right rear negative output.Purple/Black
• If the vehicle is equipped with SYNC, and desired to be retained, connect the and Red White
RCA jacks labeled “RSE/SYNC/SAT” to the audio AUX-IN jacks.
• If the vehicle is equipped without SYNC, and the AUX-IN jack is desired to be retained,
connect the and RCA jacks labeled “FROM 3.5” to the audio AUX-IN jacks.Red White
12-pin pre-wired ASWC-1 harness:
This harness is to be used along with the optional ASWC-1 (sold separately) to retain steering
wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If the ASWC-1 will be
used, please refer to the ASWC-1 instructions for radio connections and programming. Disregard
the harness that comes with the ASWC-1.
DIN jack:
The DIN jack is to be used with the optional AX-LCD (sold separately) to retain SYNC information.
Continue to Installing & Programming the AX-ADFD02
Product specificaties
| Merk: | Metra |
| Categorie: | Niet gecategoriseerd |
| Model: | Axxess AX-ADFD02 |
Heb je hulp nodig?
Als je hulp nodig hebt met Metra Axxess AX-ADFD02 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Metra
17 Juni 2025
17 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
3 Juni 2025
2 Mei 2025
2 Mei 2025
Handleiding Niet gecategoriseerd
- Estella
- ABB
- Leaptel
- Zedar
- Nikkei
- ORCA
- Analog Way
- TESLA Electronics
- TacTic
- Luminex
- Speaker Snap
- Uvex
- DPA
- Home Easy
- Universal Audio
Nieuwste handleidingen voor Niet gecategoriseerd
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025