Metra AX-BM9112 Handleiding

Metra Niet gecategoriseerd AX-BM9112

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra AX-BM9112 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-BM9112

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections to be made .......................................2

Installing the AX-BM9112 .......................................3

Programming the ASWC-1 interface .....................3

Audio level adjustment .........................................4

BMW Mini (R53) (with Harmon Kardon ampliﬁer) 2001-2006

• Provides accessory power

• Retains R.A.P. (retained accessory power)

• Retains audio controls on the steering wheel

• Retains phone buttons (radio dependent)

• Retains factory features: date, time, temperature display

• Selectable audio options

• Micro “B” USB updatable

• AX-BM9112 interface

• ASWC-1 interface

• AX-BM9112 harness

• ASWC-1 harness

• Female 3.5mm connector with stripped leads

CONNECTIONS TO BE MADE

From the aftermarket radio to the AX-BM9112 harness:

• Connect the Black wire to the ground wire.

Note:

There will also be a Black ground wire on the 12-pin pre-wired ASWC-1

harness to connect as well.

• Connect the Yellow wire to the battery wire.

• Connect the Red wire to the accessory wire.

Note:

There will also be a Red accessory wire on the 12-pin pre-wired ASWC-1

harness to connect as well.

• If the aftermarket radio has an illumination wire, connect the Orange wire to it.

• Connect the Blue wire to the antenna turn on wire.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

• The momentary switch will only be used in models that are not equipped with

steering wheel controls.

From the aftermarket radio to the ASWC-1 harness:

This harness is only to be used if the vehicle is equipped with steering wheel controls.

• Connect the Black wire to the ground wire.

• Connect the Red wire to the accessory wire.

• For the radios listed below, connect the

female 3.5mm connector with stripped leads

, to the male

3.5mm SWC jack from the ASWC-1 harness. Any remaining wires tape off and disregard:

• Eclipse: Connect the steering wheel control wire, normally Brown Brown/White, to the wire

of the connector. Then connect the remaining steering wheel control wire, normally Brown/

White, to the Brown wire of the connector.

• Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the wire.Brown

• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow wire to

the Brown wire.

• XITE: Connect the steering wheel control SWC-2 wire from the radio to the Brown wire.

• Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio.

Note:

The radio must be updated to rev. 2.1.4 or higher software.

• Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as Key-A or

SWC-1, to the Brown wire of the connector. Then connect the remaining steering wheel control

wire, referred to as Key-B or SWC-2, to the Brown/White wire of the connector. If the radio

comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual provided with

the radio for assigning the SWC buttons. Contact the radio manufacturer for more information

• For all other radios: Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the

aftermarket radio designated for an external steering wheel control interface. Please refer to the

aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

REV. 2/27/2018 INSTAX-BM9112

With the key in the off position:

• Connect the AX-BM9112 harness to the AX-BM9112 interface, and then to the wiring harness in

the vehicle.

• Connect the ASWC-1 harness to the ASWC-1 interface, and then to the AX-BM9112 interface.

• Turn the ignition on, the L.E.D. in the ASWC-1 interface will start ﬂashing rapidly, which

means the ASWC-1 is looking for the vehicle and the radio.

Note:

If the L.E.D. did not start ﬂashing rapidly, press the reset button for 3 seconds.

• After a few seconds the L.E.D. should stop ﬂashing rapidly, and then go out for

approximately 2 seconds.

• After approximately 2 seconds there will be a series of 7 Green ﬂashes, some short, and

some long. The long ﬂashes represent the wires that are connected to the ASWC-1. The 3rd,

4th, 5th, and 6th ﬂashes should be longer.

Tip:

Knowing this will help to troubleshoot, if need be.

• The L.E.D. will pause for another 2 seconds, and then ﬂash Red up to 18 times depending on

which radio is connected to the ASWC-1. Refer to the L.E.D. feedback section for information.

• This is the end of the auto detection stage. If the ASWC-1 detected the vehicle and the radio

successfully, the L.E.D. will light up solid.

•

Test the steering wheel controls for proper operation. Refer to the ASWC-1 instructions online at

axxessinterfaces.com for customizing the buttons, if so desired

INSTALLING THE AX-BM9112

PROGRAMMING THE ASWC-1 INTERFACE

PROGRAMMING THE

ASWC-1 INTERFACE

(CONT.)

Steering wheel control extra settings

L.E.D. feedback

The (18) Red L.E.D. ﬂashes represent which brand radio the ASWC-1 is connected to. Each

ﬂash represents a different radio manufacturer. For example, if you are installing a JVC radio,

the ASWC-1 will ﬂash Red (5) times, and then stop. Following is a legend that dictates which

radio manufacturer corresponds to which ﬂash.

L.E.D. feedback legend

* Note:

If the ASWC-1 ﬂashes Red (7) times, and you do not have an Alpine radio connected to

it, that means the ASWC-1 does not detect a radio connected it. Verify that the 3.5mm jack is

connected to the correct steering wheel jack/wire in the radio.

** Note:

The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be updated

to rev. 2.1.4 or higher through www.parrot.com.

† Note:

If you have a Clarion radio and the steering wheel controls do not work, change the radio type to

the other Clarion radio type; same for Eclipse. Refer to the “Programming Information” document online

‡ Note:

If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC radio,

change the radio type to a Kenwood. Refer to the “Programming Information” document online.

1 ﬂash - Eclipse (Type 1) †

2 ﬂashes - Kenwood ‡

3 ﬂashes - Clarion (Type 1) †

4 ﬂashes - Sony / Dual

5 ﬂashes - JVC

ﬂashes -

Pioneer / Jensen

7 ﬂashes - Alpine *

8 ﬂashes - Visteon

9 ﬂashes - Valor

10 ﬂashes - Clarion (Type 2) †

11 ﬂashes - Metra OE

12 ﬂashes - Eclipse (Type 2) †

13 ﬂashes - LG

14 ﬂashes - Parrot **

15 ﬂashes - XITE

16 ﬂashes - Philips

17 ﬂashes - TBD

18 ﬂashes - JBL

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	AX-BM9112

Heb je hulp nodig?

Als je hulp nodig hebt met Metra AX-BM9112 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra FD-BROPOD1 Handleiding

3 April 2024

Metra AXDIS-HK4 Handleiding

19 Maart 2024

Metra TE-AJPKT Handleiding

27 Februari 2024

Metra 99-7342 Handleiding

6 Januari 2024

Metra 70-7903 Handleiding

6 Januari 2024

Metra 99-7888 Handleiding

6 Januari 2024

Metra 99-3020 Handleiding

6 Januari 2024

Metra 99-7510 Handleiding

6 Januari 2024

Metra 70-1731 Handleiding

6 Januari 2024

Metra 99-8222BR Handleiding

6 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024

Sony PDW-U4 Handleiding

26 April 2024

Sony NXL-FR318 Handleiding

26 April 2024