Metra 99-9604B Handleiding

Metra Niet gecategoriseerd 99-9604B

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 99-9604B (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5

REV. 3/15/2016 INST99-9604

Installation instructions for part 99-9604

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Painted matte black

• A) Radio trim panel • B) Radio brackets

• C) Pocket

• D)

(8) #8 x 3/8”

Phillips pan-head screws

• E) (4) Phillips 5mm x 12mm flat-head screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • N/A

Antenna Adapter: • 40-EU10

• Panel removal tool • Phillips screwdriver

• Torx T-20 screwdriver • Pick tool

TOOLS REQUIRED

Porsche Cayenne 2003-2010

99-9604B

A B

Dash Disassembly ..................................................2

Kit Assembly

– ISO DIN radio provision with pocket ...................... 3

– ISO DDIN radio provision ...................................... 4

Table of Contents

99-9604

Unsnap and remove the trim panel

around the outside of the radio, switches,

and climate controls. (Figure A)

2. Remove (4) T-20 Torx screws to remove

the radio. (Figure B)

There are (2) different methods for

installing this kit. Option 1 does not require

the kit to be secured to the sub-dash

bracket whereas option 2 does. If choosing

option 1, skip to kit assembly. If choosing

option 2, proceed to the next step.

Using a pick tool, release (2) clips securing

the climate control switches

. (Figure C)

3. Remove (6) T-20 Torx screws to remove

the radio sub-dash bracket: (2) at the

top, (2) at the bottom, and (2) inside the

cavity at the bottom. (Figure D)

Note:

It is not necessary to completely

remove the bracket and connectors. Kit

assembly can be performed inside the

vehicle to avoid this if so desired

Continue to kit assembly

Dash Disassembly

(Figure B) (Figure D)

(Figure A) (Figure C)

99-9604

Kit Assembly

ISO DIN radio provision with pocket

Option 1

1. Remove the metal DIN sleeve and

trim ring from the aftermarket radio.

2. Attach the pocket to the lower

section of the using radio brackets

the (4) #8 x 3/8” Phillips pan-head

screws provided. (Figure A)

Slide the radio into the bracket/pocket

assembly, and then secure it using the

screws supplied with the radio. (Figure A)

Note: The screws must be flush in

the radio brackets in order to properly

slide into the factory sub-dash. (4)

5mm x 12mm Phillips flat-head

screws have been supplied if the radio

does not supply these type of screws

Locate the factory wiring harness and

antenna connector in the dash and

complete all necessary connections

to the radio. Metra recommends

using the proper mating adapter from

Metra and/or AXXESS. Test the radio

for proper operation

5. Slide the completed assembly into

the dash.

Note: The radio will simply

compress in.

6. Attach the radio trim panel over the

radio and then secure it using the

(4) factory screws removed in dash

disassembly.

7. Reassemble the dash in reverse

order of disassembly.

Option 2

1. Remove the metal DIN sleeve and

trim ring from the aftermarket radio.

2. Attach the pocket to the lower

section of the radio brackets using

the (4) #8 x 3/8” Phillips pan-head

screws provided. (Figure A)

3. Slide the radio into the bracket/

pocket assembly, and then secure it

using the screws supplied with the

radio. (Figure A)

Note:

The screws must be flush in

the radio brackets in order to properly

slide into the factory sub-dash. (4)

5mm x 12mm Phillips flat-head

screws have been supplied if the radio

does not supply these type of screws

Slide the completed assembly into the

factory sub-dash bracket removed in

dash disassembly, and then secure it

with the (4) #8 x 3/8” pan-head Phillips

screws provided, (2) on each side.

5. Locate the factory wiring harness

and antenna connector in the

dash and complete all necessary

connections to the radio. Metra

recommends using the proper

mating adapter from Metra and/or

AXXESS. Test the radio for proper

operation.

6. Install the radio/sub-dash assembly

back into the dash using the (4)

factory screws removed in dash

disassembly.

Note: The (2) screws inside the

cavity will not be reused.

7. Attach the radio trim panel over the

radio and then secure it using the

(4) factory screws removed in dash

disassembly.

8. Reassemble the dash in reverse

order of disassembly.

(Figure A)

Product specificaties

Merk:	Metra
Categorie:	Niet gecategoriseerd
Model:	99-9604B

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 99-9604B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Metra

Metra FD-BROPOD1 Handleiding

3 April 2024

Metra AXDIS-HK4 Handleiding

19 Maart 2024

Metra TE-AJPKT Handleiding

27 Februari 2024

Metra 99-7342 Handleiding

6 Januari 2024

Metra 70-7903 Handleiding

6 Januari 2024

Metra 99-7888 Handleiding

6 Januari 2024

Metra 99-3020 Handleiding

6 Januari 2024

Metra 99-7510 Handleiding

6 Januari 2024

Metra 70-1731 Handleiding

6 Januari 2024

Metra 99-8222BR Handleiding

6 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024

Sony PDW-U4 Handleiding

26 April 2024