Metra 99-8235CHG Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 99-8235CHG (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
INSTALLATION INSTRUCTIONS FOR PART 99-8235CHG
APPLICATIONS
METRA. The World’s best kits.metraonline.com1-800-221-0932 © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
REV. 9/19/2012 INST99-8235CHG
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in
beforereconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
Table of Contents
• ISO DIN head unit provision with pocket
Painted Charcoal High-Gloss
A) Radio Trim PanelB) Brackets • C) Pocket • D) Clock/Hazard Switch Bracket • E) (3) Panel Clips
• F) (6) #4 x 3/8” Phillips truss head screws G) (4) #8 x 3/8” Phillips pan head screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-1761 Non Amplified Toyota Harness • TYTO-01 Amplified Toyota Interface
Antenna Adapter: • Not Required
• Panel removal toolPhillips screwdriver • Socket Wrench
TOOLS REQUIRED
A B
Dash Disassembly
Toyota Tacoma 2012-up ....................................... 2
Kit Assembly
ISO DIN head unit provision with pocket ............... 3
C D E F G
99-8235CHG
1. Unclip and remove A/C control
panel. (Figure A)
2. Remove (4) 10 mm bolts securing
radio. (Figure B)
3. Unclip and remove entire panel
including hazard switch and clock.
(Figure C)
Dash Disassembly
SCAN
SCAN
T EXT
PWR VOL
(Figure A)
(Figure D)
(Figure B)
(Figure E)
(Figure C)
4. Remove the left and right radio
brackets from the radio chassis.
(Figure D)
5. Unclip and remove the clock/
hazard switch assembly from the
factory radio housing trim panel.
(Figure E)
Continue to kit preparation
99-8235CHG
Kit Preparation Kit Assembly
1. Attach the clock/hazard switch
bracket to the radio housing using
the (6) #4 x 3/8” Phillips pan head
screws. (Figure A)
WARNING: DO NOT OVERTIGHTEN
SCREWS.
2. Clip the clock/hazard switch
assembly into the 95-8235CHG
radio housing trim panel.
(Figure B)
3. Install the three included panel
clips to the back of the radio
housing trim panel (factory clips
can also be used if desired).
Continue to kit assembly
(Figure A)
(Figure B)
(Figure A)
(Figure B)
H
M
PASS ENGE R PAS SE NGER
H
M
PASSENGE R PASSENGE R
Insert Clock/Hazard switch assembly from
rear of 99-8235CHG radio housing trim panel
ISO DIN head unit provision
with pocket
1. Mount the pocket to the radio
brackets with the (4) #8 x 3/8”
Phillips screws supplied. (Figure A)
2. Slide the radio into the bracket/
pocket assembly and secure with
screws supplied with the radio.
(Figure B)
3. Secure the radio/pocket assembly
into the sub dash using the
factory hardware.
4. Locate the factory wiring harness
in the dash. Metra recommends
using the proper mating adapter
from Metra or AXXESS. Re-connect
the negative battery terminal and
test the unit for proper operation.
5. Reassemble dash in reverse
order of disassembly using the
99-8235CHG radio trim panel
instead of the factory panel.


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 99-8235CHG

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 99-8235CHG stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd