Metra 95-8730B Handleiding

Metra Niet gecategoriseerd 95-8730B

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 95-8730B (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Metra. The World’s Best Kits.® MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 1/8/19 INST95-8730B
I N S TA L L AT I O N I N S T R U C T I O N S
95-8730B
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
• ISO DDIN radio provision
• Includes panel for relocating the factory buttons
• Painted black
KIT COMPONENTS
• A) Radio housing • B) Radio brackets • C) Button panel housing • D) Button panel housing bracket • E) Button panel tabs (2)
• F) Button extension harness • G) Radio screws (4) •H) 3/8” screws (6) •I) 1/4” screws (2) TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• T-20 Torx screwdriver • 3mm Allen screwdriver
• Thin-head flat-blade screwdriver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly ..........................................................4
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: XSVI-9005-NAV (non-amped only)
Antenna Adapter: 40-EU10
A B
E F
DC
Mercedes E Class (W212) 2010-2013
* Left hand drive models only
Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com
specific applications
G H I
1.800.221.0932
|
MetraOnline.com
2
Radio/Button Removal:
1. Open the glove box, then pull down (2)
clips securing the a/c vent panel above
the glove box opening. (Figure A)
2. Locate the release clip inside each center
a/c vent. Using a thin-head flat-blade
screwdriver, pull out on the release clips
to free the a/c vent panel. Unclip, unplug
and remove the panel. (Figure B)
3. Unscrew (2) T-20 Torx screws on top of
the radio/button assembly until they no
longer turn easily, then pull them up as
much as they can go. Gently pull on the
radio to release it. If it doesn’t release,
slightly unscrew the screws again, and
periodically pull on the radio/button
assembly until the assembly releases.
Slide the assembly out just enough to
access the connector on the bottom *
right side of the assembly. Slide the
assembly out fully, then unplug and
remove the assembly. (Figures C & D)
Note *: This connector will connect to
the button extension harness discussed
in .Kit Preparation
Display Removal:
1. Unclip and remove the
display bezel trim. There are
(4) clips securing the trim
to the display. Shown in the
figure is the bottom left clip.
(Figure E)
Continue to Kit Preparation
(Figure E)
(Figure A)
(Figure B)
(Figure C)
(Figure D)
DASH DISASSEMBLY
REV. 1/8/2019 INST95-8730B 3
Button Relocation
1. Connect the button extension harness
to the harness removed in step 3 from
Dash Disassembly. Route this harness to
the display area up top.
2. Remove the button panel from the
factory radio:
a. Unclip the trim from the bottom of
the radio.
b.
Remove (4) screws securing the panel,
then remove the panel. (Figure A)
3. Attach the button panel to the button
panel housing:
a. Slide the button panel under the
top lip of the housing, then click the
bottom in place.
b. button panel housing Secure the
brackets to the housing using (4) of
the 3/8” screws provided. (Figure B)
c. button panel tabs Secure the to
the housing using (2) 1/4” screws
provided. Take note that the tab
closest to the driver side of the
vehicle has (2) dots. (Figures B & C)
d. Fully secure the button panel to
the assembly using the factory
hardware. (Figure D)
4. Connect the button panel to the button
extension harness in the vehicle, then
clip the assembly to the vehicle.
Housing Assembly
5. radio brackets Secure the to the radio
housing using (4) 3/8” screws provided.
(Figure E)
Continue to Kit Assembly
(Figure A)
(Figure B)
(Figure C)
KIT PREPARATION
(Figure E)
(Figure D)

Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 95-8730B

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-8730B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Metra

Metra

Metra FD-BROPOD1 Handleiding

3 April 2024
Metra

Metra AXDIS-HK4 Handleiding

19 Maart 2024
Metra

Metra TE-AJPKT Handleiding

27 Februari 2024
Metra

Metra 99-7342 Handleiding

6 Januari 2024
Metra

Metra 70-7903 Handleiding

6 Januari 2024
Metra

Metra 99-7888 Handleiding

6 Januari 2024
Metra

Metra 99-3020 Handleiding

6 Januari 2024
Metra

Metra 99-7510 Handleiding

6 Januari 2024
Metra

Metra 70-1731 Handleiding

6 Januari 2024
Metra

Metra 99-8222BR Handleiding

6 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024
Sony

Sony PDW-U4 Handleiding

26 April 2024
Sony

Sony NXL-FR318 Handleiding

26 April 2024