Metra 95-6542 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 95-6542 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
The World’s best kits.metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 7/10/17 INST95-6542
I N S TA L L A T I O N I N S T R U C T I O N S
95-6542
KIT FEATURES
ISO DDIN radio provision
Textured radio trim panel
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Radio bezel cut template • D) Sub-dash cut template • E) (1) Speed clip
TOOLS REQUIRED
• Panel removal tool • 3/8” socket wrench
• Cutting tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................2
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
Wiring Harness: • 70-1817 (sold separately)
Antenna adapter: • Not required
A B C D E
Dodge Dakota 1997-2000
Dodge Durango 1998-2000
1.800.221.0932
|
MetraOnline.com
1. Place the vehicle in park and apply the
parking brake.
2. With the key in the ignition position,
apply the foot brake and place the
shifter in low gear.
3. Tilt the steering wheel all the way down.
4. Unclip the entire dash bezel, unplugging
any wire harnesses necessary to allow
complete removal. (Figure A)
5. Remove the (2) 3/8” hex head screws
securing the radio, then unplug
and remove.
Continue to Kit Preparation
1. Clip the
radio bezel cut template
onto
the factory dash bezel, and then mark
the inside of the opening. (Figure A)
2. Remove the template, and then carefully
cut along the lines. Set aside for
Kit Assembly.
3. Place the
sub-dash cut template
into the
radio cavity in the dash, and then mark
the inside of the opening. (Figure B)
4. Remove the template, and the lower left
speed clip from the cavity, then carefully
cut the shaded areas marked out with a
suitable cutting tool.
5. Insert the
speed clip
provided with the
kit into the lower left position where the
factory clip was removed.
Continue to Kit Assembly
(Figure B)
(Figure A) (Figure A)
DASH DISASSEMBLY KIT PREPARATION
2
Remove shaded area
Remove shaded area
REV. 7/10/2017 INST95-6542
ISO DDIN radio provision
1. Attach the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
2. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra.
Test the radio for proper operation.
3. Secure the completed assembly into the
dash using the factory screws.
4. Reassemble the dash in reverse order
of disassembly.
5. Snap the
radio trim panel
onto the
factory dash bezel, over the radio.
KIT ASSEMBLY
3
(Figure A)


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 95-6542

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-6542 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd