Metra 95-3017B Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 95-3017B (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2015 METRA ELECTRONICS CORPORATION
REV. 9/8/2015 INST95-3017B
CAUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
Installation instructions for part 95-3017B
A) Radio trim panel • B) Radio brackets
20;*64765,5;:
>0905.(5;,55(*655,*;065: (sold separately)
Wiring Harness: • LC-GMRC-044 or AX-ADBOX2 and AX-ADGM04
Antenna Adapter: 40-EU55
Panel removal tool • Phillips screwdriver
• Socket wrench
;663:9,8<09,+
Chevrolet Trax 2015-up
95-3017B
A B
Dash Disassembly ................................................. 2
Kit Assembly
ISO DDIN radio provision ...................................... 3
Table of Contents
ISO DDIN radio provision
Painted to match factory finish
20;-,(;<9,:
95-3017B
2
Dash Disassembly
(Figure A) (Figure C)
(Figure B) (Figure D)
1. Unclip and remove the panel
surrounding the factory radio
including the a/c vents. (Figure A)
2. Remove (4) 9/32” screws securing
the radio chassis. (Figure B)
3. Remove (2) screws securing the
a/c vents to the factory radio trim
panel and keep for kit assembly.
(Figure C)
4. Unclip and remove the (9) metal
panel clips from the factory panel
and keep them for kit assembly.
5. Unclip and remove the (2) small
pockets on either side of the a/c
vents and keep for kit assembly.
(Figure D)
Note: Remember the process
when removing these pockets
as you will need to reinstall
them into the 99-3017B radio
panel the same way.
Continue to kit assembly
95-3017B
3
Kit Assembly
(Figure A)
ISO DDIN radio provision
1. Clip the (2) small pockets into the
95-3017B .radio trim panel
2. Attach the (9) metal panel clips to
the 95-3017B .radio trim panel
3. Attach the a/c vents to the
95-3017B with the radio trim panel
factory hardware.
4. Secure the radio brackets to the
radio using the screws supplied
with the radio. (Figure A)
5. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Re-connect the negative
battery terminal and test the radio
for proper operation.
6. Mount the new radio assembly into
the dash and reassemble the dash
in reverse order of disassembly
using the 95-3017B radio
trim panel.


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 95-3017B

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-3017B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd