Metra 70-6504 Handleiding
Metra
Niet gecategoriseerd
70-6504
Bekijk gratis de handleiding van Metra 70-6504 (5 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 362 mensen en kreeg gemiddeld 4.7 sterren uit 181.5 reviews. Heb je een vraag over Metra 70-6504 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/5
A. Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
B. Connect Black wire to Ground wire of new receiver.
C. Individually tape off any unused wires.
D. Make final wiring connections following instructions on page 5.
This wire provides a 12V switched power source. The wire must be run from the receiver
to the 12V power source as recommended in the Crutchfield MasterSheet, if available.
Following instructions, connect to a 12V source controlled by an accessory power fuse.
120 70-6504
Revision 05/26/20
Red - 12 Volts Switched Power
Yellow - 12 Volts Constant Power
Black - Chassis Ground
*120706504*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
Copyright 2020 Crutchfield Corporation
12 Volts Switched Power
Constant Power & Ground Harness
Receiver Wiring Adaptor &
Amplifier Bypass Harnesses
STEP 1 -- MATCH & CONNECT WIRES
Receiver Wiring Adaptor &
Amplifier Bypass Harnesses
120 70-6504
Page 2
White - Left Front Speaker Positive
Violet/Black - Right Rear Speaker Negative Violet - Right Rear Speaker Positive
Green - Left Rear Speaker Positive
Gray - Right Front Speaker Positive
Gray/Black - Right Front Speaker Negative
Green/Black - Left Rear Speaker Negative
White/Black - Left Front Speaker Negative
Green/White - Not Used (tape off)
White/Red - Not Used (tape off)
Yellow/Blue - Left Front Tweeter Positive
Yellow/Red - Right Front Tweeter Positive
Brown/White - Not Used (tape off)
Yellow/Black - Left Front Tweeter Negative
Yellow/Orange - Right Front Tweeter Negative
Dark Blue/Pink - Not Used (tape off)
Harness 1
Harness 2
A. Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
B. Individually tape off any unused wires.
C. Make final wiring connections following instructions on page 5.
Copyright 2020 Crutchfield Corporation
If keeping the factory tweeters, bass blockers should be used
to prevent damage to tweeters. See the next page for details.
Brown/Blue - Not Used (tape off) Brown/Yellow - Not Used (tape off)
STEP 1 -- MATCH & CONNECT WIRES (continued)
SPEAKERS
See page 3 for
instructions on
connecting these
wires.
See page 3 for
instructions on
connecting these
wires.
120 70-6504
Page 3
STEP 2 -- INSTALL
Route harnesses from receiver to amplifier location. Disconnect
harnesses from amplifier. Plug the bypass harnesses into the
matching output harnesses from the amplifier.
Yellow/Blue - Left Front Tweeter Positive
Yellow/Red - Right Front Tweeter Positive
Yellow/Black - Left Front Tweeter Negative
Yellow/Orange - Right Front Tweeter Negative
Harness 2
A. Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
B. Make final wiring connections following instructions on page 5.
Copyright 2020 Crutchfield Corporation
If using Bass Blockers:
Harness 2 Right Front Tweeter Negative
Left Front Tweeter Negative
Left Front Tweeter Positive
Right Front Tweeter Positive
4
4
Bass Blocker
Bass Blocker
Connect with Left Front Speaker and Right Front Speaker
wires respectively from harness 1 on the previous page.
See page 4 for a list of vehicles that use
this harness package and the amplifier
location in each of these vehicles.
STEP 1 -- MATCH & CONNECT WIRES (continued)
Receiver Wiring Adaptor &
Amplifier Bypass Harnesses
Product specificaties
| Merk: | Metra |
| Categorie: | Niet gecategoriseerd |
| Model: | 70-6504 |
Heb je hulp nodig?
Als je hulp nodig hebt met Metra 70-6504 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Metra
17 Juni 2025
17 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
3 Juni 2025
2 Mei 2025
2 Mei 2025
Handleiding Niet gecategoriseerd
- Kingston
- Projecta
- NuTone
- Corona
- ANT
- PUR
- Campomatic
- Verto
- Vantage Point
- ETiger
- Eufab
- Rode
- Benavent
- Ciarra
- Winix
Nieuwste handleidingen voor Niet gecategoriseerd
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025