Metra 107-HY1 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 107-HY1 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Metra. The World’s Best Kits.® MetraOnline.com © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 9/16/21 INST107-HY1
I N S TA L L AT I O N I N S T R U C T I O N S
107-HY1
Patent Pending
Attention! With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
KIT FEATURES
Designed specifically for Pioneer modular 6.8” radios like the
DMH-C2550NEX and DMH-C2500NEX.
†† Refer to the radio manufacturer for current models
Painted to match factory with a gloss black face, bright silver trim,
and matte black back plate.
Note – Pioneer extension cable required for installation. Sold separately.
KIT COMPONENTS
A) Front panel • B) Back panel • C) Brackets • D) Silver trimE) #8 x 3/8” Phillips screws (7) • F) Panel clips (4)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly ..........................................................3
A CB D E
F
Hyundai Sonata 2020-Up
Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com
specific applications
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness:
Visit metraonline.com for audio/
video and steering wheel control interface options.
Antenna Adapter: 40-KI10
1.800.221.0932
|
MetraOnline.com
2
1. Unclip the trim behind the radio and
remove (2) Phillips screws exposed.
(Figures A,B)
2. Open the passenger door, then remove
the trim panel from the side of the
dashboard. Remove (1) Phillips screw
exposed. (Figure C)
3. Unclip and remove the trim directly
below the radio. (Figure D))
DASH DISASSEMBLY
4. Remove (2) Phillips screws securing the
a/c vent panel, then unclip, unplug, and
remove. (Figure E)
5. Remove (3) screws securing the radio.
Unclip and slide the radio out, then
unplug and remove. (Figure F)
Continue to Kit Preparation
(Figure A) (Figure D)
(Figure B) (Figure E)
(Figure C) (Figure F)
REV. 9/16/2021 INST107-HY1 3
KIT ASSEMBLY
Pioneer Modular DDIN radio provision
Note: For steps 1 and 2, reference the
installation manual provided with the radio
for which hardware to use. The display
screen and radio chassis use two different
types of screws.
1. Secure the brackets to the radio chassis
using (4) screws supplied with the radio.
(Figure A)
2. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra and/
or Axxess.
3. Slide the radio assembly into to the
dash, then secure using the factory
screws. (NOTE – route screen cable to be
connected later)
4. Connect Pioneer extension cable to the
radio display screen.
5. Attach the (4) panel clips to the back
panel (Figure B)
6. Secure the radio screen display to the
back panel using (4) of the screws
supplied with the radio. (Figure C)
7. Place the silver trim back betwixt the
panel front panel and the . Assemble
together using (7) of the included
#8 x 3/8” screws. (Figure D)
8. Connect the radio display to the radio
chassis, clip the assembly into the dash,
and secure with the factory hardware.
9. Reassemble the dash in reverse
order of disassembly to complete the
installation.
(Figure A) (Figure C)
(Figure B) (Figure D)


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 107-HY1

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 107-HY1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd