Megasat DVB-T 30 Handleiding

Megasat Antenne DVB-T 30

Lees hieronder de 📖 handleiding in het Nederlandse voor Megasat DVB-T 30 (2 pagina's) in de categorie Antenne. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
DVB-T 30
Bedienungsanleitung
Einleitung:
Dies ist eine speziell entwickelte Antenne fĂźr analogen und digitalen terrestrischen Fernsehempfang.
Empfang aller TV-Signale in Ihrer Region im VHF-und UHF-Band, sowie das UKW-Radio Signal. Es ist die
beste LĂśsung fĂźr Home- und digitaler portabler TV-Empfang. Es ist sehr einfach sie zu installieren und
zu bedienen.
Einstellungen und Anschluss
• Stecken Sie den AC 230V Netzstecker (1) in die 230V Steckdose.
• Verbinden Sie das „zum TV“ Kabel (2) mit dem Antenneneingang am TV oder dem DVB-T Receiver.
Nach Überprüfung, ob alles ordnungsgemäß angeschlossen wurde, drehen Sie den im Uhrzeigersinn
den on/off Drehknopf (4), um die Antenne einzuschalten. Die LED (3) leuchtet auf und zeigt, dass der
Verstärker funktioniert. Nun schalten Sie Ihr TV-Gerät ein und wählen ein TV-Programm. Anschließend
richten Sie die Stabantennen (6), die Dipolantenne (5) und die Verstärkung des Verstärkers (4) gemäß so
ein, wie es im nächsten Abschnitt beschrieben wird.
Signal Empfang
VHF SIGNALE - I-III BAND (Kanäle 1-12)
Diese Antenne empfängt VHF Signale (analog und digital) durch die Stabantennen (6).
FĂźr den besten Empfang stellen Sie die Stabantennen wie folgt ein:
• Für BAND I: Ziehen Sie die Stabantennen komplett aus.
• Für BAND III: verkürzen die Stabantennen auf ca. 40 cm (die Verlängerung ist abhängig von dem
gewĂźnschten Kanal den Sie empfangen wollen)
• Dann bewegen Sie die Stabantennen bis Sie den besten Empfang erhalten.
UHF SIGNALE - IV-5 BAND (Kanäle 21-69)
Diese Antenne empfängt UHF Signale durch die Dipolantenne (5).
FĂźr den besten Empfang stellen Sie die Dipolantenne wie folgt ein:
• Neigen Sie den Dipol nach oben und unten
• Drehen Sie die diplo seitwärts bis Sie den besten Empfang erhalten
Verstärkungseinstellung
Um die Verstärkung einzustellen, drehen Sie den on/off Drehknopf (4), bis Sie den besten
Signalempfang bekommen:
• um die Verstärkung zu erhöhen, drehen Sie den Regler im Uhrzeigersinn,
• um die Verstärkung zu verringern, drehen Sie den Knopf gegen den Uhrzeigersinn
Hinweis: Die Antenne kann direkt am TV oder an einem DVB-T Receiver betrieben werden. Folgende
Beispiele zeigen Ihnen die AnschlĂźssmĂśglichkeit.
(Abb. 1) Direkte Verbindung zum TV
(Abb. 2) Direkte Verbindung zu einem DVB-T Receiver
Technische Daten:
• Frequenzbereich: VHF 87.5 - 230 MHz
UHF 470 - 862 MHz
• Empfangsbereich: UHF / VHF / FM
• Max. Verstärkung. VHF 30 dB / UHF 30 dB
• Ausgangssignal: max. 100 dBµV
• Widerstand: 75 Ohm
• Rauschmaß: < 3 dB
• Stromversorgung: AC 110V / 230V
Produktmerkmale::
• Variabler Verstärkungsregler
• on/off LED Betriebsleuchte
• SMD-Schaltungstechnik Design
• Integrierter High-Gain- und rauscharmer Verstärker
• Einstellbare Ringantenne für den besten UHF-Empfang
• Verstellbare Teleskop-Antennen für optimalen VHF-und FM-Radioempfang
• Speziell kompatibel mit HDTV von verschiedenen digitalen terrestrischen Signalen
(DVB-T, ISDB-T, DMB-T / H, ATSC) und DAB / FM-Radios.
Installation:
Hinweis: FĂźr den besten Empfang, ĂźberprĂźfen Sie bitte die folgenden Schritte.
1. Halten Sie die Antenne entfernt von den StÜrquellen. Halten Sie die Antenne weg von Geräten mit
großem Stromverbrauch wie z.B. Klimaanlage, Aufzug, Fön, Mikrowelle, usw.
2. Positionieren Sie die Antenne in der Nähe von einem Fenster, wenn die Antenne in Innenräumen
verwendet wird.
3. Installieren Sie die Antenne so hoch wie mĂśglich, um StĂśrungen und Unterbrechungen zwischen
Sendemast und Empfangsantenne zu vermeiden.
(1) Netzstecker (2) Signal Ausgang
(5) UHF fĂźr den
Empfang der
Kanäle 21-69
kan sich um 360°
drehen
(3) Betriebsleuchte (4) Drehknopf
(Ein/Aus und Verstärkerregler)
(6) VHF Teleskoopantenna
fĂźr den Empfang der
Kanäle 1-12
Kann hoch und runter gedreht werden
(innerhalb 180°) oder seitlich (innerhalb 180°)
Abb. 2
Abb. 1
DVB-T 30
user manual
Introduction:
This is a special designed antenna for both analog and digital terrestrial TV broadcasting reception. It
Can receive all the TV signals of your area in VHF and UHF band, as well as the FM radio signal. It is the
best solution for home reception and digital portable TV reception. It is very practical to install and very
easy to use.
Setting and connection
• Connect the AC 230V cable (1) to the 230V AC wall socket.
• Connect the TO TV cable (2) to the antenna-input socket of your TV or terrestrial digital set-top-box.
After checking that all the connections have been done properly, turn clockwise the on/off knop (4) to
switch the antenna on. LED (3) lights up showing that the amplier of indoor antenna is working. Now,
turn on your television set on and select a TV programme. then adjust the rod antennas (6), the dipole
antenna (5) and the amplier gain (4) according to what is described in next paragraphs.
Signal reception
VHF SIGNALS - I-III BAND (channels 1-12)
This antenna receives VHF signals (both analog and digital) through the rod antennas (6).
For best reception, adjust rod antennas as follow:
• For BAND I: extend completely the rod antennas
• For BAND III: shorten the rod antennas to about 16 inches (the extension de pends on the channel
you want to receiver)
• then, move the rod antennas until you get the best signal reception.
UHF SIGNALS - IV-5 BAND (channels 21-69)
This antenna receives UHF signals through dipole antenna (5).
For best reception, adjust rod antennas as follow:
• tilt the dipole up and down
• turn the diplo sideways until you get the best signal reception
Gain adjusting
In order to adjust the amplifier gain turn on/off knob (4) until to get the best signal reception:
• to increase gain, turn the knob clockwise
• to reduce gain, turn the knob anticlockwise
Note: This antenna can be used directly connected to TV or terrestrial set-top-box, please take
reference of following 2 different connecting ways to install your antenna.
(Fig. 1) Directly connected to TV
(Fig. 2) Directly connected to terrestrial set-top-box
Technical Data:
• Frequency range: VHF 87.5 - 230 MHz
UHF 470 - 862 MHz
• Receiving range: UHF / VHF / FM
• Max. gain: VHF 30 dB / UHF 30 dB
• Output level: max. 100 dBµV
• Out Impedance: 75 Ohm
• Noise figure: < 3 dB
• Power supply: AC 110V / 230V
Product Features:
• Variable gain control
• Power on/off LED indicator
• SMD circuit technology design
• Built-In high gain and low noise amplifier
• Adjustable loop aerial for the best UHF reception
• Adjustable telescopic antennas for optimum VHF and FM radio reception
• Specially compatible with HDTV of various digital terrestrial signal
(DVB-T, ISDB-T, DMB-T/H, ATSC) and DAB/FM radios.
Installation:
Note: For the best reception, please check the following conditions.
1. Keep the antenna away from the sources of interference: Keep the antenna away from those big
power consumption devices, such as air conditioner, elevator, hair dryer and microwave oven etc.
2. Place the antenna near windows when use the antenna in indoor environment.
3. Install the antenna as high as possible: In digitalterrestrial reception, if there are some interceptions
between antenna and transmission tower, it will cause the signal loss temporarily. So if the antenna
is installed as possible, those interceptions will be reduced.
(1) Power plug (2) Signal output
(5) Tilt UHF loog
for receiving
channels 21-69
can be turned 360°
(3) Power indicator light (4) Control knob
(on/off and gain adjustment
(6) VHF telescopic antenna
for receiving channels 1-12
Can be turned up and down (within 180°)
or sideways (within 180°)
Fig. 2
Fig. 1


Product specificaties

Merk: Megasat
Categorie: Antenne
Model: DVB-T 30

Heb je hulp nodig?

Als je hulp nodig hebt met Megasat DVB-T 30 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden