Mean Well RPS-120-15 Handleiding

Mean Well Niet gecategoriseerd RPS-120-15

Lees hieronder de 📖 handleiding in het Nederlandse voor Mean Well RPS-120-15 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

Installation Manual

 Type：

：

：： Medical Switching Power Supply

(1) Enclosed (Families: MSP)

(2) Modular (Families: MP, NMP)

(3) PCB (Families: MPS, MPD, MPT, MQ, RPS, RPD, RPT, RPTG, NEM, PM)

(4) Adaptor (Families: GSM, MES)

 Installation

(1) Enclosed Type

(a) Before any installation or maintenance work, please disconnect your system from the utility.

Ensure that it cannot be re-connected inadvertently!

(b) Mounting orientations other than standard orientation or operate under high ambient

temperature may increase the internal component temperature and will require a de-rating in

output current. Please refer to the specification sheets to receive the optimum mounting

position and information about the de-rating curve.

must be kept when the adjacent device is a heat source.

(d) Keep enough insulation distance between mounting screws and internal components of

Enclosed units. Please refer to case drawing on specifications to receive the maximum length of

mounting screw.

(e) Recommended wires of Enclosed units are shown as below.

AWG 18 16 14 12 10 8

Rated Current of

Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A

Cross-section of

Lead(mm2 ) 0.75 1.00 1.5 2.5 4 6

Note: The suggested maximum current above only suit for 1-4 strips, 5 or more

strips should not exceed 80% of current rating.

Make sure that all strands of each stranded wire enter the terminal connection and the screw

terminals are securely fixed to prevent poor contact.

(f) For other information about the products, please refer to www.meanwell.com for details.

(2) Modular Type

(a) Before any installation or maintenance work, please disconnect your system from the utility.

Ensure that it cannot be re-connected inadvertently!

(b) Mounting orientations other than standard orientation or operate under high ambient

temperature may increase the internal component temperature and will require a de-rating in

output current. Please refer to the specification sheets to receive the optimum mounting

position and information about the de-rating curve.

must be kept when the adjacent device is a heat source.

(d) Keep enough insulation distance between mounting screws and internal components of

Modular units. Please refer to case drawing on specifications to receive the maximum length of

mounting screw.

(e) Recommended wires of Modular units are shown as below.

AWG 18 16 14 12 10 8

Rated Current of

Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A

Cross-section of

Lead(mm2 ) 0.75 1.00 1.5 2.5 4 6

Note: The suggested maximum current above only suit for 1-4 strips, 5 or more

strips should not exceed 80% of current rating.

Make sure that all strands of each stranded wire enter the terminal connection and the screw

terminals are securely fixed to prevent poor contact.

(f) For other information about the products, please refer to www.meanwell.com for details.

Installation Manual

(3) PCB Type

(a) Before any installation or maintenance work, please disconnect your system from the utility.

Ensure that it cannot be re-connected inadvertently!

(b) Mounting orientations other than standard orientation or operate under high ambient

temperature may increase the internal component temperature and will require a de-rating in

output current. Please refer to the specification sheets to receive the optimum mounting

position and information about the de-rating curve.

must be kept when the adjacent device is a heat source.

(d) Recommended wires of PCB units are shown as below.

AWG 18 16 14 12 10 8

Rated Current of

Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A

Cross-section of

Lead(mm2 ) 0.75 1.00 1.5 2.5 4 6

Note: The suggested maximum current above only suit for 1-4 strips, 5 or more

strips should not exceed 80% of current rating.

Make sure that all strands of each stranded wire enter the terminal connection and the screw

terminals are securely fixed to prevent poor contact.

(e) At least 5mm insulation distance on the bottom of PCB units should be kept and a Mylar film

should be added between the units and the system. In addition, keep enough insulation

distance of 15mm around the PCB units.

(f) PCB units greater than 120W may require a forced air/fan for cooling. Please refer to

specifications to receive a minimum air intensity and air-flow direction.

(g) For other information about the products, please refer to www.meanwell.com for details.

(4) Adapter Type

(a) Before any installation or maintenance work, please disconnect your system from the utility.

Ensure that it cannot be re-connected inadvertently!

(b) Mounting orientations other than standard orientation or operate under high ambient

temperature may increase the internal component temperature and will require a de-rating in

output current. Please refer to the specification sheets to receive the optimum mounting

position and information about the de-rating curve.

must be kept when the adjacent device is a heat source.

(d) Before attaching the DC plug of an adaptor to equipment, please unplug the adaptor from the

AC power and verify the unit is within the voltage and current rating on the equipment.

(e) Keep the linkage between the adaptor and its power cord tightly as well as connecting the DC

plug to equipment properly.

(f) Protect the power cord of adaptors from being trodden on or being squashed.

(g) An approved power cord of an adaptor should greater or equal to SVT, 3G×18AWG or H03VV-F,

3G×0.75mm2.

(h) If the final equipment is not used for long period of time, disconnect the equipment from

adaptors to avoid being damaged by voltage peaks or lightning strike.

(i) For other information about the products, please refer to www.meanwell.com for details.

 User Manual

NMP series:

http://www.meanwell.com/webapp/product/search.aspx?prod=NMP1K2&pdf=Tk1QLUUucGRm&a=4

Installation Manual

 Warning / Caution !!

(1) Risk of electrical shock and energy hazard. All failure should be examined by a qualified technician.

Please do not remove the case of the power supply by yourself! Please do not install the units in

places with high moisture or near the water.

(2) Please do not install the units in places with high ambient temperature or near fire source. The

maximum ambient temperature, please refer to their specifications.

(3) Output current and output wattage must not exceed the rated values on specifications.

(4) To avoid risk of electric shock, for class I products, the ground (FG) must be connected to protective

earth.

(5) The Enclosed, Modular and PCB units are designed in accordance with EMC regulations and the

related test reports are available by request. Since they are belong to component power supplies

and will be installed inside system enclosure, when they are integrated into a system, the EMC

characteristics of the end system must be re-verified again.

Manufacturer：

：

：：

MEAN WELL ENTERPRISES Co., LTD.

No.28, Wuquan 3rd Rd., Wugu Dist.,

New Taipei City 24891, Taiwan

Tel: +886-2-2299-6100

Web: www.meanwell.com

Branch Office：

：

：：

China

MEAN WELL (GUANGZHOU)

ENTERPRISES Co., LTD.

2F, A Building, Yuean lndustry Park,

Huangcun,Dongpu Yown, Tianhe

District, Gungzhou, China

Post Code:510660

Tel: +86-20-2887-1200

Web: www.meanwell.com.cn

U.S.A.

MEAN WELL USA, INC.

44030 Fremont Blvd., Fremont,

CA 94538, U.S.A.

Tel: +1-510-683-8886

Web: www.meanwellusa.com

Europe

MEAN WELL EUROPE B.V.

Langs de Werf 8, 1185XT

Amstelveen, The Netherlands

Tel: +31-20-758-6000

Web: www.meanwell.eu

Product specificaties

Merk:	Mean Well
Categorie:	Niet gecategoriseerd
Model:	RPS-120-15
Gewicht:	150 g
Breedte:	50.8 mm
Diepte:	101.6 mm
Hoogte:	29 mm
Duurzaamheidscertificaten:	RoHS
Aantal per verpakking:	72 stuk(s)
Ingangsspanning:	80 - 264 V
Uitgangsvermogen:	120 W
Output current:	8 A
Spanning:	15 V