McIntosh MCD550 Handleiding

McIntosh CD-spelers/recorder MCD550

Lees hieronder de 📖 handleiding in het Nederlandse voor McIntosh MCD550 (4 pagina's) in de categorie CD-spelers/recorder. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

McIntosh Laboratory, Inc.

2 Chambers Street

Binghamton, NY 13903

www.mcintoshlabs.com

McIntosh Part No. 04170900 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com

Important Additional Operation Information Guide

ATTENTION:

RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

Safety

Instructions

Disposal

Instructions

Lithium

Batteries

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install

in accordance with the manufacturer’s instruc-

tions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other appa-

ratus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polar-

ized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong. The wide blade or the third

prong are provided for your safety. If the pro-

vided plug does not t into your outlet, consult

an electrician for replacement of the obsolete

outlet.

10. Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

11. Only use attachments/accessories specied by

the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or

table specied by the manufacturer,

or sold with the apparatus. When a

cart is used, use caution when mov-

ing the cart/apparatus combination

to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms

or when unused for long periods of time.

14. Refer all servicing to qualied service person-

nel. Servicing is required when the apparatus

has been damaged in any way, such as pow-

er-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or

has been dropped.

15. Do not expose this apparatus to dripping or

splashing and that no objects lled with liq-

uids, such as vases, should not be placed on the

equipment.

Ne pas exposer cet appareil à des éclaboussures

ou gouttelettes d’un liquide. Aucun objet rem-

plie de liquide comme par exemple un vase ne

doit être placé sur l’appareil.

16. If this equipment is supplied with a power

supply cord only, the mains plug of the power

supply cord shall remain readily operable. To

completely disconnect this apparatus from the

a.c. mains disconnect the plug from the a.c.

receptacle.

Si l’équipement est uniquement alimenté par

un cordon d’alimentation, la che du cordon

d’alimentation doit demeurer aisément acces-

sible. Pour déconnecter complètement l’équi-

pement du réseau d’alimentation, déconnecter

la che du cordon d’alimentation de la prise

murale.

17. If this equipment is supplied with AC /DC

Adapter with separate power supply cord or the

AC/DC Adapter plugging directly into an a.c.

receptacle, they shall remain readily operable.

To completely disconnect this equipment from

the a.c. mains remove the AC /DC Adapter

mains power supply cord from the a.c. recep-

tacle or remove the AC /DC Adapter when it is

directly plugged into the a.c. receptacle.

Si l’équipement est alimenté par un adaptateur

AC/DC munis d’un cordon d’alimentation ou

un adaptateur AC/DC qui est alimenté directe-

ment à la prise murale, ils doivent demeurer

aisément accessibles. Pour déconnecter com-

plètement l’équipement du réseau d’alimen-

tation, déconnecter l’adaptateur AC/DC de la

prise murale ou déconnecter le cordon d’ali-

mentation de l’adaptateur AC/DC de la prise

murale.

18. WARNING: Do not expose batteries or battery

pack to excessive heat such as sunshine, re or

the like.

AVERTISSEMENT: Les batteries ou bloc de

batteries ne doivent pas etre exposees a une

chaleur excessive telle que celle du soleil, feu

ou autre source de chaleur similaire.

19. CAUTION: danger of explosion if battery is in-

correctly replaced. Replace only with the same

or equivalent type.

ATTENTION: danger d’explosion si la pile

n’est pas remplacée correctement. Ne remplac-

er que par le même type ou un type équivalent.

20. Connect mains power supply cord only to a

mains socket outlet with a protective earthing

connection.

21. Warning: The Ethernet connector of this

equipment must not be directly connected to

a public network. Connection is to be made

only by way of a modem or router approved

for this purpose.

The lightning ash with arrowhead, within an equilateral trian-

gle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be

of sufcient magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is intend-

ed to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompa-

nying the appliance.

ATTENTION:

RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

WARNING: TO REDUCE RISK OF

FIRE OR ELECTRICAL SHOCK, DO

NOT EXPOSE THIS EQUIPMENT TO

RAIN OR MOISTURE.

NO USER-SERVICEABLE PARTS INSIDE. RE-

FER SERVICING TO QUALIFIED PERSONNEL.

TO PREVENT THE RISK OF ELEC-

TRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SER-

VICEABLE PARTS INSIDE.

IMPORTANT SAFETY

INSTRUCTIONS!

PLEASE READ THEM BEFORE

OPERATING THIS EQUIPMENT.

a) User Information acc. to FCC15.21 as following:

Changes or modications not expressly approved by

the party responsible for compliance could void the

user’s authority to operate the equipment.

b) Statement for Class B digital device acc. to FCC

15.105 as following:

NOTE: is equipment has been tested and found

to comply with the limits for a Class A/B

digital device, pursuant to part 15 of the

FCC Rules. ese limits are designed to

provide reasonable protection against harm-

ful interference in a residential installation.

is equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interfer-

ence to radio communications. However,

there is no guarantee that interference will

not occur in a particular installation. If this

equipment does cause harmful interference

to radio or television reception, which can

be determined by turning the equipment

o and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

—Reorient or relocate the receiving

antenna.

—Increase the separation between the

equipment and receiver.

—Connect the equipment into an outlet

on a circuit dierent from that to which

the receiver is connected.

—Consult the dealer or an experienced

radio/ TV technician for help.

—is device complies with Industry

Canada licence-exempt RSS stan-

dard(s). Operation is subject to the fol-

lowing two conditions: (1) this device

may not cause interference, and (2) this

device must accept any interference,

including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux

CNR d’Industrie Canada applicables

aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux

conditions suivantes : (1) l’appareil ne

doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi,

même si le brouillage est susceptible

d’en compromettre le fonctionnement.

c) e device must be kept more than 20 cm from all

persons.

FCC INFORMATION (For US and Canada Customers

Additional Safety Information specic to this product may be

contained in the Owner’s Manual supplied with this product

Outdoor Antenna Grounding

If an outside antenna or cable system is connected

to the product, be sure the antenna or cable system

is grounded so as to provide some protection against

voltage surges and built-up static charge. Article 810 of

the National Electrical Code, ANSI/NFPA 70, provides

information with reguards to proper grounding of the

mast and supporting structure, grounding of the lead-in

wire to an antenna discharge unit, and size of ground

conductors, location of antenna-discharge unit, con-

nection to ground electrodes and requirements for the

grounding electrode.

Example of antenna grounding as

per National Electrical Code,

ANSI/NFPA 70

Disposal Instructions

Waste and Disposal Instructions

It is advisable to remove the Lithium Battery from this

product and/or remote control when it is not used for an

extended period of time. This will help to extend battery

life and avoid possible damage to the product and/or

remote control.

BATTERY REMOVAL:

Perform the following steps to remove the battery from

the product and/or remote control:

1. Before removing the Lithium Battery, rst discon-

nect the AC Power Cord and/or AC/DC Adapter

from this product.

Note: Step 1 is not required when removing the Lithium

Battery from a remote control.

2. Press the tab and lift up on the Backup Battery Cov-

er and temporarily place it aside. Refer to gures 1

and 2.

3. When removing the battery from a remote control

proceed to step 4. To remove the battery from a

product proceed to step 5.

4. Refering to figure 3, press on the bottom edge of

the battery to release the battery from the molded

battery socket. Then remove the battery from inside

of the Remote Control. Proceed to step 6.

5. Refering to gure 4, use a small pocket size screw

driver (or other suitable tool) and carefully insert the

tip of the tool between the metal tab of the battery

socket and the left side of the battery. Then rotate the

tool to release the battery from the socket. Remove

the battery from inside of the product.

6. Reinstall the Battery Cover.

7. Store the battery in a cool dry place for future use or

dispose of the battery in accordance with the local

regulations for lithium battery disposal. Batteries

should never be thrown away or incinerated.

BATTERY INSTALLATION:

Perform the following steps to install the battery into the

product and/or remote control:

8. Before installing the Lithium Battery, rst discon-

nect the AC Power Cord and/or AC/DC Adapter

from this product.

Note: Step 8 is not required when installing the Lithium

Battery into a remote control.

CAUTION:

Danger of explosion if the battery is

incorrectly installed. Only install one of

the approved Lithium Batteries listed

below.

Long Life Lithium Coin Cell type battery is used in this

product and/or supplied remote control. is product

and/or supplied remote control may be supplied with a

battery depending on the country where this product

is purchased. When purchasing a battery for use in this

product and/or remote control, refer to the following list:

This product and/or the remote control supplied with

this product may contain a coin/button cell battery.

If the coin/button cell battery is swallowed, it can

cause severe internal burns in just 2 hours and can

lead to death. Keep new and used batteries away from

children. If the battery compartment does not close

securely, stop using the product and/or remote control

and keep it away from children. If you think batteries

might have been swallowed or placed inside of the

body, seek immediate medical attention.

WARNING:

DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD

AVERTISSEMENT:

NE PAS INGÉRER L’ACCUMULATEUR,

RISQUE DE BRỦLURE CHIMIQUE

[La telecommande fournie avec] Ce product con-

tient un accumulateur bouton. En cas d’ ingestion,

l’ accumulateur bouton, peut causer des brulures

internes severes en a peine 2 heures qui peuvent etre

mortelles. Conserver les accumulateurs neufs usages

hors de portee des enfants. Sile compartiment de l’

accumulateur ne se ferme pas de maniere sure, ne

plus utiliser le produit et et le tenir hors de portee des

enfants. Encas de soupcon d’ingestion d’un accumu-

later ou d’introduction dans une partie quelconque du

corps, demander immediatement un avis medical.

Lithium Battery Type

Battery Removal or Installation

Lithium Battery

Figure 1

TAB

Figure 2

LIFT

Figure 8

Contact

Points

Figure 7

CR2032

Battery

Figure 3

Figure 4

CR2032

Figure 6

CR2032

Tabs

Figure 5

Battery

Socket

9. Press the tab and lift up on the Backup Battery Cov-

er and temporarily place it aside. Refer to gures 1

and 2.

10. When installing the battery into the remote control

proceed to step 11. To install the battery into a

product proceed to step 12.

11. Orient the battery so the + symbol (engraved into

one side of the battery) is facing up. Refer to figure

7. Then insert the battery into the socket. Make

sure the battery is touching both contact points and

is seated in the socket. Refer to figure 8.

12. Orient the battery so the + symbol (engraved into

one side of the battery) is facing up. Refer to fig-

ures 5 and 6. Then insert the battery into the sock-

et. Make sure the battery is touching both contact

points and is seated in the socket.

13. Reinstall the Battery Cover.

When discarding the unit, comply with local rules or

regulations. Batteries should never be thrown

away or incinerated but disposed of in accor-

dance with the local regulations concerning

battery disposal.

North American Waste of Electrical and Electronic

Equipment Directive

Lithium Battery, Types, Removal and Installation

Approved Lithium Batteries

Brand IEC No. ANSI/NEDA No.

Energizer CR2032 5004LC1

Panasonic CR2032(PA/1B)15004LC1

1CR Lithium Coin Cells contain Perchlorate - special handling may

apply. For additional information go to https://www.dtsc.ca.gov/

hazardouswaste/perchlorate/

ATTENTION:

Danger d’explosion si la pile n’set

pas remplacée correctement. Installer

uniquement l’une des piles au lithium

approuvées énumérées ci dessous.

Product specificaties

Merk:	McIntosh
Categorie:	CD-spelers/recorder
Model:	MCD550
Kleur van het product:	Zwart, zilver
Gewicht:	12700 g
Breedte:	445 mm
Diepte:	483 mm
Hoogte:	153 mm
Gewicht verpakking:	19200 g
Ondersteund audioformaat:	MP3,WMA
Volumeregeling:	Draaiknop
Soort apparaat:	Persoonlijke cd-speler
Frequentiebereik:	4 - 40000 Hz
Signaal/ruis-verhouding:	110 dB
MP3 afspelen:	Ja
D/A-converter:	32-bit/192kHz
Playback disc types:	CD
Aantal kanalen:	2 kanalen
Totale harmonische vervorming (THD):	0.0015 procent
Ingebouwde audio D/A-converter (DAC):	Ja
Dynamisch bereik:	100 dB
SACD playback:	Ja